arXiv subjects

Youting Liang

Publications and source records attributed to Youting Liang.

13 recordsLinked to original sources

arXiv2025

2.7-octave supercontinuum generation spanning from ultraviolet to near-infrared in thin-film lithium niobate waveguides

Supercontinuum generation (SCG) with spectral coverage across the full visible and ultraviolet (UV) ranges is crucial for optical clocks, quantum computing and sensing. However, achieving such SCG in nanophotonic platforms is challenging due to the difficulties in spectrum broadening. Here, Such ultrabroad-bandwidth SCG was demonstrated in thin-film lithium niobate (TFLN) nanophotonic waveguides by dispersion management, without periodic poling for spectral broadening. Anomalous-dispersion waveguides were designed in the telecom band, simultaneously enabling dispersive wave emergence, modal-matched second harmonic generation, and third harmonic generation for spectrum broadening. Moreover, MgO was intentionally doped to mitigate the photorefractive effect of lithium niobate, which frequently results in un-sustained spectrum broadening and in turn limits the accessible SCG coverage. By leveraging photolithography assisted chemo-mechanical etching, low-loss MgO doped TFLN nanophotonic waveguides were fabricated. As a result, thanks to the utilization of the strong second-order and third-order nonlinear processes, gap-free 2.7-octave SCG spanning from 330 nm to 2250 nm was observed by pumping the waveguide with a 1550-nm femtosecond pulsed laser with 0.687 nJ, agreeing well with numerical simulation. This spectral coverage represents the state of the art in TFLN platforms without fine microdomains, and even close to the record in sophisticated chirped periodically poled TFLN waveguides.

physics.optics↗

arXiv2024

Compact low-half-wave-voltage thin film lithium niobate electro-optic phase modulator fabricated by photolithography assisted chemo-mechanical etching

This paper presents a compact dual-arm thin film lithium niobate (TFLN) electro-optic phase modulator fabricated using the photolithography-assisted chemo-mechanical etching (PLACE) technique. The design of the device allows for complete utilization of the microwave electric field, doubling the modulation efficiency compared to single-arm modulators in theory. With a half-wave voltage of approximately 3 V and a modulation length of 1 cm, the device outperforms conventional phase modulators. Furthermore, the phase modulator exhibits low sensitivity to optical wavelengths in the range of 1510-1600 nm and offers a low insertion loss of 2.8 dB. The capability to generate multiple sideband signals for optical frequency comb applications is also demonstrated, producing 29 sideband signals at an input microwave power of 2 W.

physics.optics↗

arXiv2023

Thin Film Lithium Niobate Electro-optic Isolator Fabricated by photolithography assisted chemo-mechanical etching (PLACE)

We report a thin-film lithium niobate electro-optic isolator fabricated by photolithography-assisted chemo-mechanical etching in this work. The device demonstrates 39.50 dB isolation when subjected to a 24 GHz microwave of 25.5 dBm on its electrodes. The measured isolation remains consistently above 30 dB within the 1510 nm to 1600 nm wavelength range. The overall device insertion loss, specifically the fiber-to-fiber insert loss, has been measured to be 2.6 dB, which is attributed to our highly efficient spot size converter and the low propagation loss observed in the fabricated waveguides.

physics.optics↗

arXiv2023

Gigahertz-rate-switchable wavefront shaping through integration of metasurfaces with photonic integrated circuit

Achieving spatiotemporal control of light at high-speeds presents immense possibilities for various applications in communication, computation, metrology, and sensing. The integration of subwavelength metasurfaces and optical waveguides offers a promising approach to manipulate light across multiple degrees of freedom at high-speed in compact photonic integrated circuit (PICs) devices. Here, we demonstrate a gigahertz-rate-switchable wavefront shaping by integrating metasurface, lithium niobite on insulator (LNOI) photonic waveguide and electrodes within a PIC device. As proofs of concept, we showcase the generation of a focus beam with reconfigurable arbitrary polarizations, switchable focusing with lateral focal positions and focal length, orbital angular momentum light beams (OAMs) as well as Bessel beams. Our measurements indicate modulation speeds of up to gigahertz rate. This integrated platform offers a versatile and efficient means of controlling light field at high-speed within a compact system, paving the way for potential applications in optical communication, computation, sensing, and imaging.

physics.optics↗

arXiv2023

On-chip arrayed waveguide grating fabricated on thin film lithium niobate

We design an on-chip 8-channel TFLN AWG and fabricate the device using photolithography assisted chemo-mechanical etching (PLACE) technique. We experimentally measure the transmission of the fabricated TFLN AWG near the central wavelength of 1550 nm. We obtain an on-chip loss as low as 3.32 dB, a single-channel bandwidth of 1.6 nm and a total-channel bandwidth of 12.8 nm. The crosstalk between adjacent channels was measured to be below -7.01 dB within the wavelength range from 1543 nm to 1558 nm, and the crosstalk between non-adjacent channels was below -15 dB.

physics.optics↗

arXiv2023

Electro-optically programmable photonic circuits enabled by wafer-scale integration on thin-film lithium niobate

Programmable photonic circuits performing universal linear-optical transformations underpin vital functions in photonic quantum information processing, quantum-enhanced sensor networks, machine learning and many other intriguing applications. Recent advances in photonic integrated circuits facilitate monolithic integration of externally controlled Mach-Zehnder interferometers which can implement arbitrary unitary transformation on a large number of input/output modes. In this work, we demonstrate a 4x4 programmable linear photonic circuit on lithium niobate on insulator platform employing fast, power-efficient and low-loss electro-optical phase shifters, showing enormous advantages in terms of configuration rate and power consumption. Our device is capable of fast switching with 500 ps rise time and 1.7 ns fall time, and possesses a total on-chip power dissipation of only 0.015 mW when operated at 1 MHz modulation, and an insertion loss of 0.15 dB for each modulator and an on-chip extinction ratio of -34 dB for both cross and bar routes.

physics.optics↗

arXiv2022

On-chip integrated Yb3+-doped waveguide amplifiers on thin film lithium niobate

We report the fabrication and optical characterization of Yb3+-doped waveguide amplifiers (YDWA) on the thin film lithium niobate fabricated by photolithography assisted chemo-mechanical etching. The fabricated Yb3+-doped lithium niobate waveguides demonstrates low propagation loss of 0.13 dB/cm at 1030 nm and 0.1 dB/cm at 1060 nm. The internal net gain of 5 dB at 1030 nm and 8 dB at 1060 nm are measured on a 4.0 cm long waveguide pumped by 976nm laser diodes, indicating the gain per unit length of 1.25 dB/cm at 1030 nm and 2 dB/cm at 1060 nm, respectively. The integrated Yb3+-doped lithium niobate waveguide amplifiers will benefit the development of a powerful gain platform and are expected to contribute to the high-density integration of thin film lithium niobate based photonic chip.

physics.optics↗

arXiv2022

Monolithically integrated waveguide-coupled single-frequency microlaser on erbium-doped thin film lithium niobate

We overcome the difficulty in realizing a monolithic waveguide-coupled microring laser integrated on erbium-doped thin film lithium niobate (Er: TFLN) using photolithography assisted chemo-mechanical etching (PLACE) technique. We demonstrate an integrated single-frequency microring laser operating around 1531 nm wavelength. The PLACE technique, enabling integrated Er: TFLN photonics with low propagation loss, can thus be used to realize low cost mass production of monolithic on-chip microlasers with applications ranging from optical communication and photonic integrated circuit (PIC) to precision metrology and large-scale sensing.

physics.optics↗

arXiv2022

High-production-rate fabrication of low-loss lithium niobate electro-optic modulators using photolithography assisted chemo-mechanical etching (PLACE)

Integrated thin-film lithium niobate (LN) electro-optic (EO) modulators of broad bandwidth, low insertion loss, low cost and high production rate are essential elements in contemporary inter-connection industries and disruptive applications. Here, we demonstrated the design and fabri-cation of a high performance thin-film LN EO modulator using photolithography assisted chemo-mechanical etching (PLACE) technology. Our device shows a 3-dB bandwidth over 50 GHz, along with a comparable low half wave voltage-length product of 2.16 Vcm. We obtain a fiber-to-fiber insertion loss of 2.6 dB.

physics.app-ph↗

arXiv2021

A high-gain cladded waveguide amplifier on erbium doped thin-film lithium niobate fabricated using photolithography assisted chemo-mechanical etching

Erbium doped integrated waveguide amplifier and laser prevail in power consumption, footprint, stability and scalability over the counterparts in bulk materials, underpinning the lightwave communication and large-scale sensing. Subject to the highly confined mode and moderate propagation loss, gain and power scaling in such integrated micro-to-nanoscale devices prove to be more challenging compared to their bulk counterparts. In this work, stimulated by the prevalent success of double-cladding optical fiber in high-gain/power operation, a Ta2O5 cladding is employed in the erbium doped lithium niobate (LN) waveguide amplifier fabricated on the thin film lithium niobate on insulator (LNOI) wafer by the photolithography assisted chemomechanical etching (PLACE) technique. Above 20 dB small signal internal net gain is achieved at the signal wavelength around 1532 nm in the 10 cm long LNOI amplifier pumped by the diode laser at ~980 nm. Experimental characterizations reveal the advantage of Ta2O5 cladding in higher optical gain compared with the air-clad amplifier, which is further explained by the theoretical modeling of the LNOI amplifier including the guided mode structures and the steady-state response of erbium ions.

physics.optics↗

arXiv2021

On-chip multi-color microdisk laser on Yb3+-doped thin-film lithium niobate

We demonstrate an on-chip Yb3+-doped lithium niobate (LN) microdisk laser. The intrinsic quality factors of the fabricated Yb3+-doped LN microdisk resonator are measured up to 3.79x10^5 at 976 nm wavelength and 1.1x10^6 at 1514 nm wavelength. The multi-mode laser emissions are obtained in a band from 1020 nm to 1070 nm pumped by 984 nm laser and with the low threshold of 103 {\mu}W, resulting in a slope efficiency of 0.53% at room temperature. Furthermore, the second-harmonic frequency of pump light and the sum-frequency of the pump light and laser emissions are both generated in the on-chip Yb3+-doped LN microdisk benefited from the strong \c{hi}(2) nonlinearity of LN. These microdisk lasers are expected to contribute to the high-density integration of LNOI-based photonic chip.

physics.optics↗

arXiv2021

On-chip ultra-narrow-linewidth single-mode microlaser on lithium niobate on insulator

We report an on-chip single mode microlaser with low-threshold fabricated on Erbium doped lithium niobate on insulator (LNOI). The single mode laser emission at 1550.5 nm wavelength is generated in a coupled photonic molecule, which is facilitated by Vernier effect when pumping the photonic molecule at 970 nm. A threshold pump power as low as 200 uW is demonstrated thanks to the high quality factor above 10^6. Moreover, the linewidth of the microlaser reaches 4 kHz, which is the best result in LNOI microlasers. Such single mode micro-laser lithographically fabricated on chip is highly in demand by photonic community.

physics.optics↗

arXiv2021

On-chip integrated waveguide amplifiers on Erbium-doped thin film lithium niobate on insulator

We demonstrate on-chip light amplification with integrated optical waveguide fabricated on erbium-doped thin film lithium niobate on insulator (TFLNOI) using the photolithography assisted chemo-mechanical etching (PLACE) technique. A maximum internal net gain of 18 dB in the small-signal-gain regime is measured at the peak emission wavelength of 1530 nm for a waveguide length of 3.6 cm, indicating a differential gain per unit length of 5 dB/cm. This work paves the way to the monolithic integration of diverse active and passive photonic components on the TFLNOI platform.

physics.optics↗