arXiv subjects

Xiaolin Wang

Publications and source records attributed to Xiaolin Wang.

124 records · Page 7Linked to original sources

arXiv2015

Influence of core NA on Thermal-Induced Mode Instabilities in High Power Fiber Amplifiers

We report on the influence of core NA on thermal-induced mode instabilities (MI) in high power fiber amplifiers. Influence of core NA and V-parameter on MI has been investigated numerically. It shows that core NA has larger influence on MI for fibers with smaller core-cladding-ratio, and the influence of core NA on threshold is more obvious when the amplifiers are pumped at 915nm. The dependence of threshold on V-parameter revealed that the threshold increases linearly as V-parameter decreases when V-parameter is larger than 3.5, and the threshold shows exponentially increase as V-parameter decreases when V-parameter is less than 3.5. We also discussed the effect of linewidth on MI, which indicates that the influence of linewidth can be neglected for linewidth smaller than 1nm when the fiber core NA is smaller than 0.07 and fiber length is shorter than 20m. Fiber amplifiers with different core NA were experimentally analyzed, which agreed with the theoretical predictions.

physics.optics↗

arXiv2015

Polarization Effects on Thermal-Induced Mode Instabilities in High Power Fiber Lasers

We present detailed studies of the effect of polarization on thermal-induced mode instability (MI) in ytterbium-doped fiber amplifiers. Based on a steady-state theoretical model, which takes both electric fields along the two principal axes into consideration, the effect of polarization effects on the gain of Stokes wave was analyzed, which shows that the polarization characteristics of the fiber laser have no impact on the threshold of MI. Experimental validation of the theoretical analysis is presented with experimental results agreeing well with the theoretical results, in which polarization-maintained and non-polarization-maintained fiber lasers with core/inner cladding diameter of 30/250um and core NA of 0.07 were employed. The MI threshold power is measured to be about 367~386W.

physics.optics↗

arXiv2015

Investigation of Electron-Phonon Coupling in Epitaxial Silicene by In-situ Raman Spectroscopy

In this letter, we report that the special coupling between Dirac fermion and lattice vibrations, in other words, electron-phonon coupling (EPC), in silicene layers on Ag(111) surface was probed by an in-situ Raman spectroscopy. We find the EPC is significantly modulated due to tensile strain, which results from the lattice mismatch between silicene and the substrate, and the charge doping from the substrate. The special phonon modes corresponding to two-dimensional electron gas scattering at edge sites in the silicene were identified. Detecting relationship between EPC and Dirac fermion through the Raman scattering will provide a direct route to investigate the exotic property in buckled two-dimensional honeycomb materials.

cond-mat.mtrl-sci↗

arXiv2014

Hydrostatic pressure induced transition from δTc to δl pinning mechanism in MgB2

The impact of hydrostatic pressure up to 1.2 GPa on the critical current density (Jc) and the nature of the pinning mechanism in MgB2 have been investigated within the framework of the collective theory. We found that the hydrostatic pressure can induce a transition from the regime where pinning is controlled by spatial variation in the critical transition temperature (δT_c) to the regime controlled by spatial variation in the mean free path (δl). Furthermore, Tc and low field Jc are slightly reduced, although the Jc drops more quickly at high fields than at ambient pressure. We found that the pressure raises the anisotropy and reduces the coherence length, resulting in weak interaction of the vortex cores with the pinning centres. Moreover, the hydrostatic pressure can reduce the density of states [Ns(E)], which, in turn, leads to a reduction in the critical temperature from 39.7 K at P = 0 GPa to 37.7 K at P = 1.2 GPa.

cond-mat.supr-con↗

arXiv2014

Effects of Oxygen Adsorption on the Surface State of Epitaxial Silicene on Ag(111)

Epitaxial silicene, which is one single layer of silicon atoms packed in a honeycomb structure, demonstrates a strong interaction with the substrate that dramatically affects its electronic structure. The role of electronic coupling in the chemical reactivity between the silicene and the substrate is still unclear so far, which is of great importance for functionalization of silicene layers. Here, we report the reconstructions and hybridized electronic structures of epitaxial 4x4 silicene on Ag(111), which are revealed by scanning tunneling microscopy and angle-resolved photoemission spectroscopy. The hybridization between Si and Ag results in a metallic surface state, which can gradually decay due to oxygen adsorption. X-ray photoemission spectroscopy confirms the decoupling of Si-Ag bonds after oxygen treatment as well as the relatively oxygen resistance of Ag(111) surface, in contrast to 4x4 silicene [with respect to Ag(111)]. First-principles calculations have confirmed the evolution of the electronic structure of silicene during oxidation. It has been verified experimentally and theoretically that the high chemical activity of 4x4 silicene is attributable to the Si pz state, while the Ag(111) substrate exhibits relatively inert chemical behavior.

cond-mat.mes-hall↗

arXiv2014

Tuning the Band Gap in Silicene by Oxidation

Silicene monolayers grown on Ag(111) surfaces demonstrate a band gap that is tunable by oxygen adatoms from semimetallic to semiconducting type. By using low-temperature scanning tunneling microscopy, it is found that the adsorption configurations and amounts of oxygen adatoms on the silicene surface are critical for band-gap engineering, which is dominated by different buckled structures in R13xR13, 4x4, and 2R3x2R3 silicene layers. The Si-O-Si bonds are the most energy-favored species formed on R13xR13, 4x4, and 2R3x2R3 structures under oxidation, which is verified by in-situ Raman spectroscopy as well as first-principles calculations. The silicene monolayers retain their structures when fully covered by oxygen adatoms. Our work demonstrates the feasibility of tuning the band gap of silicene with oxygen adatoms, which, in turn, expands the base of available two-dimensional electronic materials for devices with properties that is hardly achieved with graphene oxide.

cond-mat.mtrl-sci↗

arXiv2014

Tuning the conductance of H$_{2}$O@C$_{60}$ by position of the encapsulated H$_{2}$O

The change of conductance of single molecule junctions in response to various external stimuli is the fundamental mechanism for single-molecule electronic devices with multiple functionalities. We propose a concept that the conductance of molecule systems can be tuned from its inside. The conductance is varied in C$_{60}$ with encapsulated H$_{2}$O, H$_{2}$O@C$_{60}$. The transport properties of the H$_{2}$O@C$_{60}$-based nanostructure sandwiched between electrodes are studied using first-principles calculations based on the non-equilibrium Green's function formalism. Our results show that the conductance of the H$_{2}$O@C$_{60}$ is sensitive to the position of the H$_{2}$O and its dipole direction inside the cage with changes in conductance up to 20%. Our study paves a way for the H$_{2}$O@C$_{60}$ molecule to be a new platform for novel molecule based electronics and sensors.

cond-mat.mes-hall↗

arXiv2014

Unabridged phase diagram for single-phased FeSexTe1-x thin films

A complete phase diagram and its corresponding physical properties are essential prerequisites to understand the underlying mechanism of iron based superconductivity. For the structurally simplest 11 (FeSeTe) system, earlier attempts using bulk samples have not been able to do so due to the fabrication difficulties. Here, thin FeSexTe1-x films with the Se content covering the full range were fabricated by using pulsed laser deposition method. Crystal structure analysis shows that all films retain the tetragonal structure in room temperature. Significantly, the highest superconducting transition temperature (TC = 20 K) occurs in the newly discovered domain, 0.6 - 0.8. The single-phased superconducting dome for the full Se doping range is the first of its kind in iron chalcogenide superconductors. Our results present a new avenue to explore novel physics as well as to optimize superconductors.

cond-mat.supr-con↗

arXiv2014

Mitigating of Modal Instabilities in Linearly-Polarized Fiber Amplifiers by Shifting Pump Wavelength

We investigated the effct of pump wavelength on the modal instabilities (MI) in high power linearly-polarized Yb-doped fiber amplifiers. We built a novel semi-analytical model to determine the frequency coupling characteristics and power threshold of MI, which indicates promising MI suppression through pumping at an appropriate wavelength. By pumping at 915nm, the threshold can be enhanced by a factor of 2.36 as compared to that pumped at 976nm. Based on a high power linearly-polarized fiber amplifier platform, we studied the influence of pump wavelength experimentally. The threshold has been increased by a factor of 2 at 915nm, which agrees with the theoretical calculation and verified our theoretical model. Furthermore, we show that MI suppression by detuning the pump wavelength is weakened for fiber with large core-to-cladding ratio.

physics.optics↗

arXiv2014

1.3kW monolithic linearly-polarized single-mode MOPA and strategies for mitigating mode instabilities

We report on the high power amplification of 1064nm linearly-polarized laser in all-fiber polarization-maintained MOPA, which can operate at output power level of 1.3kW. The main amplifier was pumped with six 915nm laser diodes, and the slope efficiency is 65.3%. The beam quality (M2) was measured to be <1.2 at full power operation. The polarization extinction rate of the fiber amplifier was measured to be above 94% before mode instabilities (MI) sets in, which reduced to about 90% after the onset of MI. Power scaling capability of strategies for suppressing MI is analyzed based on a novel semi-analytical model, the theoretical results of which agree with the experimental results. It shows that mitigating MI by coiling the gain fiber is an effective and practical way in standard double-cladding large mode area fiber, and, by tight coiling of the gain fiber to the radius of 5.5cm, the MI threshold can be increased to 3 times higher than that without coiling or loose coiling. Experimental study has been carried out to verify the idea, which has proved that MI was suppressed successfully in the amplifier by tight coiling.

physics.optics↗

arXiv2014

Hydrostatic pressure: A very effective approach to significantly enhance critical current density in granular Sr4V2O6Fe2As2 superconductor

Pressure is well known to significantly raise the superconducting transition temperature, Tc, in both iron pnictides and cuprate based superconductors. Little work has been done, however, on how pressure can affect the flux pinning and critical current density in the Fe-based superconductors. Here, we propose to use hydrostatic pressure to significantly enhance flux pinning and Tc in polycrystalline pnictide bulks. We have chosen Sr4V2O6Fe2As2 polycrystalline samples as a case study. We demonstrate that the hydrostatic pressure up to 1.2 GPa can not only significantly increase Tc from 15 K (underdoped) to 22 K, but also significantly enhance the irreversibility field, Hirr, by a factor of 4 at 7 K, as well as the critical current density, Jc, by up to 30 times at both low and high fields. It was found that pressure can induce more point defects, which are mainly responsible for the Jc enhancement. In addition, we found that the transformation from surface pinning to point pinning induced by pressure was accompanied by a reduction of anisotropy at high temperatures. Our findings provide an effective method to significantly enhance Tc, Jc, Hirr, and the upper critical field, Hc2, for other families of Fe-based superconductors in the forms of wires/tapes, films, and single crystal and polycrystalline bulks.

cond-mat.supr-con↗

arXiv2013

Optimizing snake locomotion on an inclined plane

We develop a model to study the locomotion of snakes on an inclined plane. We determine numerically which snake motions are optimal for two retrograde traveling-wave body shapes---triangular and sinusoidal waves---across a wide range of frictional parameters and incline angles. In the regime of large transverse friction coefficient, we find power-law scalings for the optimal wave amplitudes and corresponding costs of locomotion. We give an asymptotic analysis to show that the optimal snake motions are traveling-wave motions with amplitudes given by the same scaling laws found in the numerics.

physics.bio-ph↗

arXiv2013

Application of particle swarm optimization for enhanced cyclic steam stimulation in a offshore heavy oil reservoir

Three different variations of PSO algorithms, i.e. Canonical, Gaussian Bare-bone and Lévy Bare-bone PSO, are tested to optimize the ultimate oil recovery of a large heavy oil reservoir. The performance of these algorithms was compared in terms of convergence behaviour and the final optimization results. It is found that, in general, all three types of PSO methods are able to improve the objective function. The best objective function is found by using the Canonical PSO, while the other two methods give similar results. The Gaussian Bare-bone PSO may picks positions that are far away from the optimal solution. The Lévy Bare-bone PSO has similar convergence behaviour as the Canonical PSO. For the specific optimization problem investigated in this study, it is found that the temperature of the injection steam, CO2 composition in the injection gas, and the gas injection rates have bigger impact on the objective function, while steam injection rate and the liquid production rate have less impact on the objective function.

cs.CE↗

arXiv2012

Intermittent Josephson effect with feedback voltage and temperature oscillations in graphite-coated nanocapsules with superconducting TaC core

An intermittent Josephson effect in the form of voltage and temperature oscillations in the voltage - current curves near 2 K is observed in pellets consisting of superconducting TaC nanocapsules coated with graphite. This phenomenon is attributed to non-equilibrium conditions, when Cooper pairs across a junction, which stimulate the emission of photons and the feedback temperature change of the junction. It occurs in a three-dimensional granular framework composed of TaC/carbon/TaC tunneling junctions with a Mott metal-insulator transition, below the critical temperature Tc of non-ideal type-II superconductor TaC.

cond-mat.supr-con↗

arXiv2011

s-d Electronic interactions induced H2 dissociation on the γ-U(100) surface and influences of niobium doping

The dissociation of hydrogen molecules on the γ-U(100) surface is systematically studied with the density functional theory method. Through potential energy surface calculations, we find that hydrogen molecules can dissociate without any barriers on the clean γ-U(100) surface. After careful electronic analysis, it is found that charge transfer between the hydrogen s and uranium d electronic states causes the dissociation, which is quite different from the dissociation of hydrogen molecules on other actinide metal surfaces. Considering that doping of 3d transition metal atoms can stabilize the αphase of U, we also study the influences of Nb-doping on the hydrogen dissociation process. We find that the 3d electronic states of Nb also take part in the hybridization with hydrogen s electronic states, which leads to the result that hydrogen molecules also dissociate without any energy barriers on the doped U surface. In addition, the free electronic energy lowers down more quickly for a hydrogen molecule approaching the doped U surface.

cond-mat.mtrl-sci↗

arXiv2009

A bubble-powered micro-rotor: conception, manufacturing, assembly, and characterization

A steady fluid flow, called microstreaming, can be generated in the vicinity of a micro-bubble excited by ultrasound. In this article, we use this phenomenon to assemble and power a microfabricated rotor at rotation speeds as high as 625 rpm. The extractible power is estimated to be on the order of a few femtowatts. A first series of experiments with uncontrolled rotor shapes is presented, demonstrating the possibility of this novel actuation scheme. A second series of experiments with 65 micron rotors micromanufactured in SU-8 resin are presented. Variables controlling the rotation speed and rotor stability are investigated, such as the bubble diameter, the acoustic excitation frequency and amplitude, and the rotor geometry. Finally, an outlook is provided on developing this micro-rotor into a MEMS-based motor capable of delivering tunable, infinitesimal rotary power at the microscale.

physics.flu-dyn↗