arXiv subjects

Victor Coco

Publications and source records attributed to Victor Coco.

12 recordsLinked to original sources

arXiv2026

OPTIMA, a board dedicated to Optimized Precision Timing for Multichannel Acquisition

In the new era of HL-LHC experiments, fast-timing detectors are emerging as critical tools for background rejection. Typical requirements include a temporal hit resolution of about 50 ps, a spatial resolution of around 12 $\mu$m, and radiation hardness up to $10^{17}$n$_\text{eq}$/cm$^2$. To address these challenges, the development of non-standard sensor designs and advanced fast readout electronics is required. The OPTIMA multichannel board addresses the need for testing small sensor demonstrators when they cannot yet be bonded to dedicated readout ASICs. It provides fast readout of up to 16 channels and can be integrated into various test setups, including test beam environments. This contribution presents the design of the OPTIMA board, its integration in test beams, and the first experimental results.

physics.ins-det↗

arXiv2025

The Timepix4 Beam Telescope

The spatial and temporal performance of a telescope system comprising planar silicon sensors bump-bonded to Timepix4-v2 ASICs are assessed at the CERN SPS using a $180$~GeV/$c$ mixed hadron beam. The pointing resolution at the centre of the telescope is $2.3 \pm 0.1\;\mathrm{\mu m}$ and $2.4 \pm 0.1\mathrm{\mu m}$ in x and y directions, respectively. The temporal resolution for the combined timestamps on a track using only the information from the Timepix4 planes is found to be $92 \pm 5$~ps. The telescope is extensively described including its data acquisition system and dedicated software as well as the corrections applied to the raw measurements.

hep-ex↗

arXiv2024

Timing resolution performance of Timepix4 bump-bonded assemblies

The timing performance of the Timepix4 application-specific integrated circuit (ASIC) bump-bonded to a $100\;\mu\textrm{m}$ thick n-on-p silicon sensor is presented. A picosecond pulsed infrared laser was used to generate electron-hole pairs in the silicon bulk in a repeatable fashion, controlling the amount, position and time of the stimulated charge signal. The timing resolution for a single pixel has been measured to $107\;\textrm{ps}$ r.m.s. for laser-stimulated signals in the silicon sensor bulk. Considering multi-pixel clusters, the measured timing resolution reached $33\;\textrm{ps}$ r.m.s. exploiting oversampling of the timing information over several pixels.

physics.ins-det↗

arXiv2023

Fabrication of a Silicon Electron Multiplier sensor using Metal Assisted Chemical Etching and its characterisation

The Silicon Electron Multiplier (SiEM) sensor is a novel sensor concept that enables charge multiplication by high electric fields generated by embedded metal electrodes within the sensor bulk. Metal assisted chemical etching (MacEtch) in gas phase with platinum as a catalyst has been used to fabricate test structures consisting of vertically aligned silicon pillars and strips on top of a silicon bulk. The pillars exceed 10 $\mu m$ in height with a diameter of 1.0 $\mu m$ and are arranged as a hexagonal lattice with a pitch of 1.5 $\mu m$. Electrical characterisations through current $-$ voltage measurements inside a scanning electron microscope and a climate chamber have demonstrated that the MacEtch process is compatible with active media and p-n junctions.

physics.ins-det↗

arXiv2022

Reconstruction of charged tracks with Timepix4 ASICs

The design of a detector system comprised of four silicon sensors bump-bonded to Timepix4 ASICs is described together with its data acquisition system, operational infrastructure, and dedicated software. The spatial and temporal performance of the system are assessed with a 180 GeV/c mixed hadron beam at the CERN SPS and reported in detail. Particle tracks are reconstructed using time-space measurements from the four detector planes. The spatial hit resolution is assessed to be $(15.5\pm 0.5)$ $\mu$m and $(4.5\pm0.3)$ $\mu$m for 100 and 300 $\mu$m thick sensors, respectively. The timestamps from the detectors are also measured with fine precision, yielding time resolutions of $(452\pm10)$ ps, $(420\pm10)$ ps, $(639\pm10)$ ps, $(631\pm10)$ ps for the two 100 and two 300 $\mu$m thick sensors respectively. These measurements are combined to a track time resolution of $(340\pm 5)$ ps.

physics.ins-det↗

arXiv2022

The Road Ahead for CODEX-b

In this Snowmass contribution we present a comprehensive status update on the progress and plans for the proposed CODEX-b detector, intended to search for long-lived particles beyond the Standard Model. We review the physics case for the proposal and present recent progress on optimization strategies for the detector and shielding design, as well as the development of new fast and full simulation frameworks. A summary of the technical design for a smaller demonstrator detector (CODEX-$\beta$) for the upcoming Run~3 of the LHC is also discussed, alongside the road towards realization of the full experiment at the High-Luminosity LHC.

hep-ex↗

arXiv2022

The Silicon Electron Multiplier Sensor

The Silicon Electron Multiplier (SiEM) is a novel sensor concept for minimum ionizing particle (MIP) detection which uses internal gain and fine pitch to achieve excellent temporal and spatial resolution. In contrast to sensors where the gain region is induced by doping (LGADs, APDs), amplification in the SiEM is achieved by applying an electric potential difference in a composite electrode structure embedded within the silicon bulk using MEMS fabrication techniques. Since no gain-layer deactivation is expected with radiation damage, such a structure is expected to withstand fluences of up to $10^{16} n_{eq}$. Various geometries and biasing configurations are studied, within the boundaries imposed by the fabrication process being considered. The effective gain, the field in the sensor, the leakage current and breakdown conditions are studied for cell sizes in the range of $6 - 15 \mu m$. Simulations show that gains in excess of 10 can be achieved, and studies of the time structure of the induced signals from a charge cloud deposited in the middle of the sensor show that time resolutions similar to other sensors with internal gain can be expected. Plans for the manufacture of a proof-of-concept sensor and for its subsequent characterisation are discussed.

physics.ins-det↗

arXiv2021

Microchannel cooling for the LHCb VELO Upgrade I

The LHCb VELO Upgrade I, currently being installed for the 2022 start of LHC Run 3, uses silicon microchannel coolers with internally circulating bi-phase \cotwo for thermal control of hybrid pixel modules operating in vacuum. This is the largest scale application of this technology to date. Production of the microchannel coolers was completed in July 2019 and the assembly into cooling structures was completed in September 2021. This paper describes the R\&D path supporting the microchannel production and assembly and the motivation for the design choices. The microchannel coolers have excellent thermal peformance, low and uniform mass, no thermal expansion mismatch with the ASICs and are radiation hard. The fluidic and thermal performance is presented.

physics.ins-det↗

arXiv2019

Background studies for the CODEX-b experiment: measurements and simulation

This report presents results from a background measurement campaign for the CODEX-b proposal undertaken in August, 2018. The data were recorded in the DELPHI side of the LHCb cavern behind a 3.2~m concrete shield wall, during Run~2 proton-proton collisions with the goal of calibrating the simulation for the full CODEX-b detector. The maximum flux rate in the DELPHI side of the cavern was found to be around 0.6~mHz/cm$^2$ across a vertical plane just behind the shield wall, parallel to the beam line. A detailed simulation under development within the LHCb {\tt Gauss} framework is described. This includes shielding elements pertinent for CODEX-b's acceptance -- the LHCb detector, the shield wall and cavern infrastructure. Additional flux from tracks not in the line of sight from the interaction point, but bent by the magnetic fields, are incorporated. Overall, the simulation overestimates the background flux compared to the measurement. Several cross-checks and avenues for further investigations are described.

physics.ins-det↗

arXiv2019

Expression of Interest for the CODEX-b Detector

This document presents the physics case and ancillary studies for the proposed CODEX-b long-lived particle (LLP) detector, as well as for a smaller proof-of-concept demonstrator detector, CODEX-$\beta$, to be operated during Run 3 of the LHC. Our development of the CODEX-b physics case synthesizes `top-down' and `bottom-up' theoretical approaches, providing a detailed survey of both minimal and complete models featuring LLPs. Several of these models have not been studied previously, and for some others we amend studies from previous literature: In particular, for gluon and fermion-coupled axion-like particles. We moreover present updated simulations of expected backgrounds in CODEX-b's actively shielded environment, including the effects of shielding propagation uncertainties, high-energy tails and variation in the shielding design. Initial results are also included from a background measurement and calibration campaign. A design overview is presented for the CODEX-$\beta$ demonstrator detector, which will enable background calibration and detector design studies. Finally, we lay out brief studies of various design drivers of the CODEX-b experiment and potential extensions of the baseline design, including the physics case for a calorimeter element, precision timing, event tagging within LHCb, and precision low-momentum tracking.

hep-ex↗

arXiv2019

Calibration and operation of SiPM-based cameras for gamma-ray astronomy in presence of high night-sky light

The next generation of Cherenkov telescope cameras feature Silicon Photo Multipliers (SiPM), which can guarantee excellent performance and allow for observation also under moonlight, increasing duty-cycle and therefore the physics reach. A 4 m-diameter Davies-Cotton prototype telescope with a 9-degree optical FoV and a 1296-pixel SiPM camera, has been designed to meet the requirements of the next generation of ground-based gamma-ray observatories at the highest energies. The large-scale production of the telescopes for array deployment has required the development of a fully automated calibration strategy which relies on a dedicated hardware, the Camera Test Setup (CTS). For each camera pixel, the CTS is equipped with two LEDs, one operated in pulsed mode to reproduce signal and one in continuous mode to reproduce night-sky background. In this contribution we will present the camera calibration strategy, from the laboratory measurement to the on-site monitoring with emphasis on the results obtained with the first camera prototype. In addition, key performances such as charge resolution, time resolution and trigger efficiencies and their degradation with increasing night-sky background level will be presented.

astro-ph.IM↗

arXiv2019

Monte Carlo study of a single SST-1M prototype for the Cherenkov Telescope Array

The SST-1M telescope was developed as a prototype of a Small-Size-Telescope for the Cherenkov Telescope Array observatory and it has been extensively tested in Krakow since 2017. In this contribution we present validation of the Monte Carlo model of the prototype and expected performance in Krakow conditions. We focus on gamma/hadron separation and mono reconstruction of energy and gamma photon arrival direction using Machine learning methods.

astro-ph.HE↗