arXiv subjects

Tanuj Kumar

Publications and source records attributed to Tanuj Kumar.

10 recordsLinked to original sources

arXiv2026

Material selection for mid-infrared thin-film coatings and windows

We summarized the room-temperature optical properties for infrared-transparent materials, defining transparency windows for two different applications: thin-film coatings (absorption coefficient $\alpha < 10 cm^{-1}$) and windows ($\alpha < 1 cm^{-1}$). The transparency requirements for thin films are substantially less stringent, enabling the use of many more optical materials for a given wavelength range. To make an easy-to-use reference, we categorized materials by chemical group, crystallinity, and typical deposition technique, and discussed practical pros and cons such as chemical and thermal stability, mechanical hardness, and cost. The datasets and plotting scripts are provided so that users can regenerate transparency-window maps for different applications. If you do optical design at infrared wavelengths, we recommend that you print out the figures and stick them on your wall.

physics.optics↗

arXiv2026

Cool windows: simultaneously engineering high visible transparency and strong solar rejection

For window applications in hot climates, it is desirable to have windows with high visible transparency, while maintaining strong reflectance in both the ultraviolet and near infrared, to minimize unwanted heat gain. Given that more than 70% of incident solar energy is at wavelengths shorter than 1000 nm, achieving spectrally abrupt transitions from transparent to reflecting at the boundaries of the visible is essential. Such abrupt transitions at multiple wavelengths typically would require tens of dielectric layers, which is impractical for most window applications. Here, we propose and realize a structure comprising only eight planar layers that achieves sharp reflectance changes at ~390 and ~680 nm, resulting in high visible transmittance (>70%), and high near-infrared (>80%) and UV (>60%) reflectance, as well as high mid-infrared emissivity (>90%) for additional radiative cooling. We demonstrate that our engineered window reduces air temperature by up to 3.8 {\deg}C inside an enclosed box simulating a vehicle, compared to a box with a reference window.

physics.optics↗

arXiv2024

Preventing overfitting in infrared ellipsometry using temperature dependence: fused silica as a case study

Fitting oscillator models to variable-angle spectroscopic ellipsometry (VASE) data can lead to non-unique, unphysical results. We demonstrate using temperature-dependent trends to prevent overfitting and ensure model physicality. As a case study, we performed mid-infrared VASE measurements on fused silica (SiO2) of various grades, from room temperature to 600 {\deg}C. We fitted oscillator models independently at each temperature, and confirmed the model's physical validity by observing the expected monotonic trends in vibrational oscillator parameters. Using this technique, we generated a highly accurate dataset for the temperature-dependent complex refractive index of fused silica for modeling mid-infrared optical components such as thermal emitters.

physics.optics↗

arXiv2024

Self-referencing photothermal common-path interferometry to measure absorption of Si3N4 membranes for laser-light sails

Laser-light sails are a spacecraft concept wherein lightweight "sails" are propelled by high-intensity lasers. We investigated the near-infrared absorption of free-standing membranes of stoichiometric silicon nitride (Si$_3$N$_4$), a candidate sail material. To resolve the small but non-zero optical loss, we used photothermal common-path interferometry (PCI), for which we developed a self-referencing modality where a PCI measurement is performed twice: once on a bare membrane, and a second time with monolayer graphene deposited on the membrane. The graphene increases the absorption of the sample by orders of magnitude, such that it can be measured by ellipsometry, without significantly affecting the thermal properties. We measured the absorption coefficient of Si$_3$N$_4$ to be (1.5-3) $\times$ 10$^{-2}$ cm$^{-1}$ at 1064 nm, making it a suitable sail material for laser intensities as high as ~10 GW/m$^2$. By comparison, silicon-rich "low stress" SiN$_x$ (x~1), with a measured absorption coefficient of approximately 8 cm$^{-1}$, is unlikely to survive such high laser intensities. Our self-referencing technique enables testing of low-loss membranes of various materials for laser sails and other applications.

physics.optics↗

arXiv2023

ChatGPT-4 with Code Interpreter can be used to solve introductory college-level vector calculus and electromagnetism problems

We evaluated ChatGPT 3.5, 4, and 4 with Code Interpreter on a set of college-level engineering-math and electromagnetism problems, such as those often given to sophomore electrical engineering majors. We selected a set of 13 problems, and had ChatGPT solve them multiple times, using a fresh instance (chat) each time. We found that ChatGPT-4 with Code Interpreter was able to satisfactorily solve most problems we tested most of the time -- a major improvement over the performance of ChatGPT-4 (or 3.5) without Code Interpreter. The performance of ChatGPT was observed to be somewhat stochastic, and we found that solving the same problem N times in new ChatGPT instances and taking the most-common answer was an effective strategy. Based on our findings and observations, we provide some recommendations for instructors and students of classes at this level.

cs.AI↗

arXiv2022

NFDLM: A Lightweight Network Flow based Deep Learning Model for DDoS Attack Detection in IoT Domains

In the recent years, Distributed Denial of Service (DDoS) attacks on Internet of Things (IoT) devices have become one of the prime concerns to Internet users around the world. One of the sources of the attacks on IoT ecosystems are botnets. Intruders force IoT devices to become unavailable for its legitimate users by sending large number of messages within a short interval. This study proposes NFDLM, a lightweight and optimised Artificial Neural Network (ANN) based Distributed Denial of Services (DDoS) attack detection framework with mutual correlation as feature selection method which produces a superior result when compared with Long Short Term Memory (LSTM) and simple ANN. Overall, the detection performance achieves approximately 99\% accuracy for the detection of attacks from botnets. In this work, we have designed and compared four different models where two are based on ANN and the other two are based on LSTM to detect the attack types of DDoS.

cs.CR↗

arXiv2019

Development of On Board Computer for a Nanosatellite

This paper describes the process of conceptualization, design, and testing of the Onboard Computer (OBC) Software for a 3U nanosatellite. The on-board computer of the satellite is responsible for initiating dataflow between onboard hardware, performing image compression, and run control algorithms like fine pointing, sun pointing, ground pointing for payload operation and idle state detumbling. The actuation is carried out by interfacing magnetorquers and reaction wheels with the OBC. The software of the onboard computer is implemented on a Linux based operating system run on the ARM Cortex A9 processor which is part of the Zynq-7000 SoC. A Field Programmable Gate Array (FPGA) is used specifically for image compression. The compressed image is stored in a serial flash memory shared between the camera and the FPGA. The architecture comprises of a system-wide I2C bus to which the sensors interfaced. The collected data is used for logging followed by downlink and as input to algorithms used for pointing and detumbling. An SPI interface is used between the Power Subsystem microcontroller and the On-Board Computer since a large amount of housekeeping data will have to be exchanged at high rates. Reaction wheels and magnetorquers are actuated by current driver circuits which get the control signals from the OBC. The satellite is modelled as a Finite State Machine for software development. The states broadly fall under two categories, Normal and Emergency. Each state has a predetermined set of logical tasks to be run, which are abstracted as separate processes in the memory. State transitions take place by polling the health metrics of the satellite. However, hardware interrupts are implemented on selected peripherals which ensure an asynchronous switching to the Emergency States for safety. A review of some common fault detection, isolation and removal methods used shall conclude the paper.

eess.SY↗

arXiv2014

Hydro-dynamics of surface patterning by ion beam irradiation: an interface phenomenon

We show that the ion beam induced incompressible amorphous solid flow in terms of advection transport mechanism leads to the erosion and deposition of atoms at the amorphous/crystalline (a/c) interface resulting in the formation of pattern at the a/c interface as well as at the free surface. The ion beam impact generated erosion and mass redistribution at the free surface are found to have insignificant effect in patterning of surface. By varying the thicknesses of amorphous layer, it has been established that a/c interface plays the dominant role in surface patterning. The morphological variation of Si surface after 50 keV Ar+ ion bombardment has been investigated by atomic force microscopy (AFM) and cross-sectional transmission electron microscopy (X-TEM) as a function of ion fluence. Navier-Stokes flow inside the amorphous layer coupled with the Exner equation successfully explains the growth mechanism of surface patterning.

cond-mat.mtrl-sci↗

arXiv2012

Ion beam generated surface ripples: new insight in the underlying mechanism

A new hydrodynamic mechanism is proposed for the ion beam induced surface patterning on solid surfaces. Unlike the standard mechanisms based on the ion beam impact generated erosion and mass redistribution at the free surface (proposed by Bradley-Harper (BH) and its extended theories), the new mechanism proposes that the ion beam induced saltation and creep processes, coupled with incompressible solid flow in amorphous layer, leads to the formation of ripple patterns at the amorphous/crystalline (a/c) interface and hence at the free surface. Ion beam stimulated solid flow inside the amorphous layer controls the wavelength, where as the amount of material transported and re-deposited at a/c interface control the amplitude of ripples. The new approach is verified by designed experiments and supported by the discrete simulation method.

cond-mat.mtrl-sci↗

arXiv2009

Anomalous structure and dynamics of the Gaussian-core fluid

It is known that there are thermodynamic states for which the Gaussian-core (GC) fluid displays anomalous properties such as expansion upon isobaric cooling (density anomaly) and increased single-particle mobility upon isothermal compression (self-diffusivity anomaly). We investigate how temperature and density affect its short-range translational structural order, as characterized by the two-body excess entropy. We find that there is a wide range of conditions for which the short-range translational order of the GC fluid decreases upon isothermal compression (structural order anomaly). The origin of the structural anomaly is qualitatively similar to that of other anomalous fluids and is connected to how compression affects static correlations at different length scales. We find that the self-diffusivity of the GC fluid obeys a scaling relationship with the two-body excess entropy that is very similar to the one observed for a variety of simple liquids. One consequence of this relationship is that the state points for which structural, self-diffusivity, and density anomalies of the Gaussian-core fluid occur appear as cascading regions on the temperature-density plane, a phenomenon observed earlier for models of waterlike fluids. There are, however, key differences between the anomalies of GC and waterlike fluids, and we discuss how those can be qualitatively understood by considering the respective interparticle potentials of these models. Finally, we note that the self-diffusivity of the Gaussian-core fluid obeys different scaling laws depending on whether the two-body or total excess entropy is considered. This finding, which deserves more comprehensive future study, appears to underscore the significance of higher-body correlations for the behavior of fluids with bounded interactions.

cond-mat.soft↗