arXiv ScienceSearch

arXiv subjects

M. Grayson

Publications and source records attributed to M. Grayson.

At least 19 recordsLinked to original sources

Generalized Fit for Asymptotic Predictions of Heavy-Tail Experimental Transients

Transient responses in disordered systems typically show a heavy-tail relaxation behavior: the decay time constant increases as time increases, revealing a spectral distribution of time constants. The asymptotic value of such transients is notoriously difficult to experimentally measure due to the increasing decay time-scale. However, if the heavy-tail transient is plotted versus log-time, a reduced set of data around the inflection point of such a plot is sufficient for an accurate fit. From a derivative plot in log-time, the peak height, position, line width, and, most importantly, skewness are all that is needed to accurately predict the asymptotic value of various heavy-tail decay models to within less than a percent. This curve fitting strategy reduces by orders of magnitude the amount of experimental data required, and clearly identifies a threshold below which the amount of data is insufficient to distinguish various models. The skew normal spectral fit and dispersive diffusion transient fit are proposed as four-parameter fits, with the latter including the stretched exponential as a limiting case. The line fit and asymptotic prediction are demonstrated using experimental transient responses in previously published amorphous silicon and amorphous InGaZnO data.

cond-mat.dis-nn

Driving Perpendicular Heat Flow: Ambipolar Transverse Thermoelectrics for Microscale and Cryogenic Peltier Cooling

Whereas thermoelectric performance is normally limited by the figure of merit ZT, transverse thermoelectrics can achieve arbitrarily large temperature differences in a single leg even with inferior ZT by being geometrically tapered. We introduce a band-engineered transverse thermoelectric with p-type Seebeck in one direction and n-type orthogonal, resulting in off-diagonal terms that drive heat flow transverse to electrical current. Such materials are advantageous for microscale devices and cryogenic temperatures -- exactly the regimes where standard longitudinal thermoelectrics fail. InAs/GaSb type II superlattices are shown to have the appropriate band structure for use as a transverse thermoelectric.

cond-mat.mtrl-sci

Thermal conductivity of InAs/GaSb superlattice

The cross-plane thermal conductivity of a type II InAs/GaSb superlattice (T2SL) is measured from 13 K to 300 K using the 3{\omega} method. Thermal conductivity is reduced by up to 2 orders of magnitude relative to the GaSb bulk substrate. The low thermal conductivity of around 1-8 W/m\cdotK may serve as an advantage for thermoelectric applications at low temperatures, while presenting a challenge for T2SL quantum cascade lasers and high power light emitting diodes. We introduce a power-law approximation to model non-linearities in the thermal conductivity, resulting in increased or decreased peak temperature for negative or positive exponents, respectively.

cond-mat.mtrl-sci

Generalized four-point characterization method for resistive and capacitive contacts

In this paper, a four-point characterization method is developed for resistive samples connected to either resistive or capacitive contacts. Provided the circuit equivalent of the complete measurement system is known including coaxial cable and connector capacitances as well as source output and amplifier input impedances, a frequency range and capacitive scaling factor can be determined, whereby four-point characterization can be performed. The technique is demonstrated with a discrete element test sample over a wide frequency range using lock-in measurement techniques from 1 Hz - 100 kHz. The data fit well with a circuit simulation of the entire measurement system. A high impedance preamplifier input stage gives best results, since lock-in input impedances may differ from manufacturer specifications. The analysis presented here establishes the utility of capacitive contacts for four-point characterizations at low frequency.

cond-mat.other

Separating parallel conduction from two-dimensional magnetotransport in high mobility InP/InGaAs MOCVD-grown heterostructures

In this Letter, four-point magnetotransport of high mobility InGaAs/InP heterointerfaces is measured from 1.6 K to 300 K and from 0 to 15 T, and an analysis is shown whereby the mobility and density of the two-dimensional (2D) accumulation layer can be separately characterized from that of the parallel conducting dopant layer over all but a small intermediate temperature range. Standard magnetotransport regimes are defined as the temperature increases from 1.6 K to 300 K, namely quantum Hall (QH), Shubnikov de Haas (SdH), and Drude regimes (D), and in the QH and D regimes different analyses are applied to deduce densities and mobilities of both layers separately. Quantitative conditions for the intermediate SdH regime are defined, within which both QH and D analyses fail. The density and activation energy of unintentional donors at the InP epilayer/substrate interface is deduced. At base temperature, QH minima are resolved down to B = 0.4 T at nu = 20, revealing a mobility of mu = 160,000 cm^2/Vs. The 2D system maintains this high mobility up to at least 40 K in this high quality structure.

cond-mat.mes-hall

Valley degeneracy in biaxially strained aluminum arsenide quantum wells

This paper details a complete formalism for calculating electron subband energy and degeneracy in strained multi-valley quantum wells grown along any orientation with explicit results for the AlAs quantum well case. A standardized rotation matrix is defined to transform from the conventional- cubic-cell basis to the quantum-well-transport basis whereby effective mass tensors, valley vectors, strain matrices, anisotropic strain ratios, and scattering vectors are all defined in their respective bases. The specific cases of (001)-, (110)-, and (111)-oriented aluminum arsenide (AlAs) quantum wells are examined, as is the unconventional (411) facet, which is of particular importance in AlAs literature. Calculations of electron confinement and strain in the (001), (110), and (411) facets determine the critical well width for crossover from double- to single-valley degeneracy in each system. The notation is generalized to include miscut angles, and can be adapted to other multi-valley systems. To help classify anisotropic inter-valley scattering events, a new primitive unit cell is defined in momentum space which allows one to distinguish purely in-plane inter-valley scattering events from those that requires an out-of-plane momentum scattering component.

cond-mat.mes-hall

The visibility of IQHE at sharp edges: Experimental proposals based on interactions and edge electrostatics

The influence of the incompressible strips on the integer quantized Hall effect (IQHE) is investigated, considering a cleaved-edge overgrown (CEO) sample as an experimentally realizable sharp edge system. We propose a set of experiments to clarify the distinction between the large-sample limit when bulk disorder defines the IQHE plateau width and the small-sample limit smaller than the disorder correlation length, when self-consistent edge electrostatics define the IQHE plateau width. The large-sample or bulk QH regime is described by the usual localization picture, whereas the small-sample or edge regime is discussed within the compressible/incompressible strips picture, known as the screening theory of QH edges. Utilizing the unusually sharp edge profiles of the CEO samples, a Hall bar design is proposed to manipulate the edge potential profile from smooth to extremely sharp. By making use of a side-gate perpendicular to the two dimensional electron system, it is shown that the plateau widths can be changed or even eliminated altogether. Hence, the visibility of IQHE is strongly influenced when adjusting the edge potential profile and/or changing the dc current direction under high currents in the non-linear transport regime. As a second investigation, we consider two different types of ohmic contacts, namely highly transmitting (ideal) and highly reflecting (non-ideal) contacts. We show that if the injection contacts are non-ideal, however still ohmic, it is possible to measure directly the non-quantized transport taking place at the bulk of the CEO samples. The results of the experiments we propose will clarify the influence of the edge potential profile and the quality of the contacts, under quantized Hall conditions.

cond-mat.mes-hall

Single-valley high-mobility (110) AlAs quantum wells with anisotropic mass

We studied a doping series of (110)-oriented AlAs quantum wells (QWs) and observed transport evidence of single anisotropic-mass valley occupancy for the electrons in a 150 Åwide QW. Our calculations of strain and quantum confinement for these samples predict single anisotropic-mass valley occupancy for well widths $W$ greater than 53 Å. Below this, double-valley occupation is predicted such that the longitudinal mass axes are collinear. We observed mobility anisotropy in the electronic transport along the crystallographic directions in the ratio of 2.8, attributed to the mass anisotropy as well as anisotropic scattering of the electrons in the X-valley of AlAs.

cond-mat.mes-hall

Nanometer-scale sharpness in corner-overgrown heterostructures

A corner-overgrown GaAs/AlGaAs heterostructure is investigated with transmission and scanning transmission electron microscopy, demonstrating self-limiting growth of an extremely sharp corner profile of 3.5 nm width. In the AlGaAs layers we observe self-ordered diagonal stripes, precipitating exactly at the corner, which are regions of increased Al content measured by an XEDS analysis. A quantitative model for self-limited growth is adapted to the present case of faceted MBE growth, and the corner sharpness is discussed in relation to quantum confined structures. We note that MBE corner overgrowth maintains nm-sharpness even after microns of growth, allowing the realization of corner-shaped nanostructures.

cond-mat.mtrl-sci

Hopping conduction in strongly insulating states of a diffusive bent quantum Hall junction

Transport studies of a bent quantum Hall junction at integer filling factors show strongly insulating states at higher fields. In this paper we analyze the strongly insulating behavior as a function of temperature T and dc bias V, in order to classify the localization mechanisms responsible for the insulating state. The temperature dependence suggests a crossover from activated nearest-neighbor hopping at higher T to variable-range hopping conduction at lower T. The base temperature electric field dependence is consistent with 1D variable-range hopping conduction. We observe almost identical behavior at filling factors 1 and 2, and discuss how the bent quantum Hall junction conductance appears to be independent of the bulk spin state. Various models of 1D variable-range hopping which either include or ignore interactions are compared, all of which are consistent with the basic model of disorder coupled counter-propagating quantum Hall edges.

cond-mat.mes-hall

Donor binding energy and thermally activated persistent photoconductivity in high mobility (001) AlAs quantum wells

A doping series of AlAs (001) quantum wells with Si delta-modulation doping on both sides reveals different dark and post-illumination saturation densities, as well as temperature dependent photoconductivity. The lower dark two-dimensional electron density saturation is explained assuming deep binding energy of Delta_DK = 65.2 meV for Si-donors in the dark. Persistent photoconductivity (PPC) is observed upon illumination, with higher saturation density indicating shallow post-illumination donor binding energy. The photoconductivity is thermally activated, with 4 K illumination requiring post-illumination annealing to T = 30 K to saturate the PPC. Dark and post-illumination doping efficiencies are reported.

cond-mat.mes-hall

Novel metallic and insulating states at a bent quantum Hall junction

A non-planar geometry for the quantum Hall (QH) effect is studied, whereby two quantum Hall (QH) systems are joined at a sharp right angle. When both facets are at equal filling factor nu the junction hosts a channel with non-quantized conductance, dependent on nu. The state is metallic at nu = 1/3, with conductance along the junction increasing as the temperature T drops. At nu = 1, 2 it is strongly insulating, and at nu = 3, 4 shows only weak T dependence. Upon applying a dc voltage bias along the junction, the differential conductance again shows three different behaviors. Hartree calculations of the dispersion at the junction illustrate possible explanations, and differences from planar QH structures are highlighted.

cond-mat.mes-hall

Vertical quantum wire realized with double cleaved-edge overgrowth

A quantum wire is fabricated on (001)-GaAs at the intersection of two overgrown cleaves. The wire is contacted at each end to n+ GaAs layers via two-dimensional (2D) leads. A sidegate controls the density of the wire revealing conductance quantization. The step height is strongly reduced from 2e^2/h due to the 2D-lead series resistance. We characterize the 2D density and mobility for both cleave facets with four-point measurements. The density on the first facet is modulated by the substrate potential, depleting a 2um wide strip that defines the wire length. Micro-photoluminescence shows an extra peak consistent with 1D electron states at the corner.

cond-mat.mes-hall

Classical-to-stochastic Coulomb blockade cross-over in aluminum arsenide wires

We report low-temperature differential conductance measurements in aluminum arsenide cleaved-edge overgrown quantum wires in the pinch-off regime. At zero source-drain bias we observe Coulomb blockade conductance resonances that become vanishingly small as the temperature is lowered below $250 {\rm mK}$. We show that this behavior can be interpreted as a classical-to-stochastic Coulomb blockade cross-over in a series of asymmetric quantum dots, and offer a quantitative analysis of the temperature-dependence of the resonances lineshape. The conductance behavior at large source-drain bias is suggestive of the charge density wave conduction expected for a chain of quantum dots.

cond-mat.mes-hall

Four-point measurements of n- and p-type two-dimensional systems fabricated with cleaved-edge overgrowth

We demonstrate a contact design that allows four-terminal magnetotransport measurements of cleaved-edge overgrown two-dimensional electron and hole systems. By lithographically patterning and etching a bulk-doped surface layer, finger-shaped leads are fabricated, which contact the two-dimensional systems on the cleave facet. Both n- and p-type two-dimensional systems are demonstrated at the cleaved edge, using Si as either donor or acceptor, dependent on the growth conditions. Four-point measurements of both gated and modulation-doped samples yield fractional quantum Hall features for both n- and p-type, with several higher-order fractions evident in n-type modulation-doped samples.

cond-mat.mes-hall

Anomalous magnetoresistance peak in (110) GaAs two-dimensional holes: Evidence for Landau-level spin-index anticrossings

We measure an anomalous magnetoresistance peak within the lowest Landau level (nu = 1) minimum of a two-dimensional hole system on (110) GaAs. Self-consistent calculations of the valence band mixing show that the two lowest spin-index Landau levels anticross in a perpendicular magnetic field B consistent with where the experimental peak is measured, Bp. The temperature dependence of the anomalous peak height is interpreted as an activated behavior across this anticrossing gap. Calculations of the spin polarization in the lowest Landau levels predict a rapid switch from about -3/2 to +3/2 spin at the anticrossing. The peak position Bp is shown to be affected by the confinement electrostatics, and the utility of a tunable anticrossing position for spintronics applications is discussed.

cond-mat.mes-hall

Aluminum arsenide cleaved-edge overgrown quantum wires

We report conductance measurements in quantum wires made of aluminum arsenide, a heavy-mass, multi-valley one-dimensional (1D) system. Zero-bias conductance steps are observed as the electron density in the wire is lowered, with additional steps observable upon applying a finite dc bias. We attribute these steps to depopulation of successive 1D subbands. The quantum conductance is substantially reduced with respect to the anticipated value for a spin- and valley-degenerate 1D system. This reduction is consistent with disorder-induced, intra-wire backscattering which suppresses the transmission of 1D modes. Calculations are presented to demonstrate the role of strain in the 1D states of this cleaved-edge structure.

cond-mat.mes-hall

Influence of voltmeter input impedance on quantum Hall effect measurements

We report on the influence of voltmeters on measurements of the longitudinal resistance in the quantum Hall effect regime. We show that for typical input resistances for standard digital lock-in amplifiers the longitudinal resistance can show a non-zero minimum which might be mistaken for parallel conduction in the doping layer. In contrast to a real parallel conduction the effect disappears when either the current source and ground contact are swapped or the polarity of the B-field is changed. We discuss the influence of input capacitances and stray capacitances on the measurement. The data demonstrates the influence of the voltmeter input impedance on the longitudinal resistance measurement.

cond-mat.mes-hall