arXiv subjects

Fredrik Lundell

Publications and source records attributed to Fredrik Lundell.

25 records · Page 2Linked to original sources

arXiv2018

Buoyant finite-size particles in turbulent duct flow

Particle Image Velocimetry (PIV) and Particle Tracking Velocimetry (PTV) have been employed to investigate the dynamics of finite-size spherical particles, slightly heavier than the carrier fluid, in a horizontal turbulent square duct flow. Interface resolved Direct Numerical Simulations (DNS) have also been performed with the Immersed Boundary Method (IBM) at the same experimental conditions, bulk Reynolds number $Re_{2H}$ = 5600, duct height to particle size ratio $2H/d_p$ = 14.5, particle volume fraction $Φ$ = 1% and particle to fluid density ratio $ρ_p/ρ_f$ = 1.0035. A good agreement has been observed between experiments and simulations in terms of the overall pressure drop, concentration distribution and turbulent statistics of the two phases. Additional experimental results considering two particle sizes, $2H/d_p$ = 14.5 and 9 and multiple $Φ$ = 1, 2, 3, 4 and 5% are reported at the same $Re_{2H}$. The pressure drop monotonically increases with the volume fraction, almost linearly and nearly independently of the particle size for the above parameters. However, despite the similar pressure drop, the microscopic picture, the fluid velocity statistics, differs significantly with the particle size. This one-to-one comparison between simulations and experiments extends the validity of interface resolved DNS in complex turbulent multiphase flows and highlights the ability of experiments to investigate such flows in considerable details, even in regions where the local volume fraction is relatively high.

physics.flu-dyn↗

arXiv2018

Turbulent duct flow with polymers

We have performed direct numerical simulation of the turbulent flow of a polymer solution in a square duct, with the FENE-P model used to simulate the presence of polymers. First, a simulation at a fixed moderate Reynolds number is performed and its results compared with those of a Newtonian fluid to understand the mechanism of drag reduction and how the secondary motion, typical of the turbulent flow in non-axisymmetric ducts, is affected by polymer additives. Our study shows that the Prandtl's secondary flow is modified by the polymers: the circulation of the streamwise main vortices increases and the location of the maximum vorticity move towards the center of the duct. In-plane fluctuations are reduced while the streamwise ones are enhanced in the center of the duct and dumped in the corners due to a substantial modification of the quasi-streamwise vortices and the associated near-wall low- and high-speed streaks; these grow in size and depart from the walls, their streamwise coherency increasing. Finally, we investigated the effect of the parameters defining the viscoelastic behavior of the flow and found that the Weissenberg number strongly influences the flow, with the cross-stream vortical structures growing in size and the in-plane velocity fluctuations reducing for increasing flow elasticity.

physics.flu-dyn↗

arXiv2018

Experimental investigation of turbulent suspensions of spherical particles in a square duct

We report experimental observations of turbulent flow with spherical particles in a square duct. Three particle sizes namely: $2H/d_{p}$ = 40, 16 and 9 ($2H$ being the duct full height and $d_{p}$ being the particle diameter) are investigated. The particles are nearly neutrally-buoyant with respect to the suspending fluid. Refractive Index Matched - Particle Image Velocimetry is used for fluid velocity measurement even at the highest particle volume fraction (20%) and Particle Tracking Velocimetry for the particle velocity statistics for the flows seeded with particles of the two largest sizes, whereas only pressure measurements are reported for the smallest particles. Settling effects are seen at the lowest bulk Reynolds number $Re_{2H}\approx$ 10000 whereas, at the highest $Re_{2H}\approx$ 27000, particles are in almost full suspension. The friction factor of the suspensions is found to be significantly larger than that of single-phase duct flow at the lower $Re_{2H}$ investigated; however, the difference decreases when increasing the flow rate and the total drag approaches the values of the single phase flow at the higher Reynolds number considered. The pressure drop is found to decrease with the particle diameter for volume fractions lower than $ϕ$ = 10% for nearly all $Re_{2H}$. However, at the highest volume fraction $ϕ$ = 20%, we report a peculiar non-monotonic behavior: the pressure drop first decreases and then increases with increasing particle size. The decrease of the turbulent drag with particle size at the lowest volume fractions is related to an attenuation of the turbulence. The drag increase for the two largest particle sizes at $ϕ$ = 20%, however, occurs despite this large reduction of the turbulent stresses, and it is therefore due to significant particle-induced stresses.

physics.flu-dyn↗

arXiv2018

Orientation and dynamics of stiff polymeric nanoparticles

Successful assembly of suspended nanoscale rod-like particles depends on fundamental phenomena controlling rotational and translational diffusion. Despite the significant developments in fluidic fabrication of nanostructured materials, the ability to quantify the dynamics in processing systems remains challenging. Here we demonstrate an experimental method for characterization of the orientation dynamics of nanorod suspensions in assembly flows using birefringence relaxation. The methodology is illustrated using nanocelluloses (cellulose nanocrystals and nanofibrils) as model systems, where the coupling of rotational diffusion coefficients to particle size distributions as well as flow-induced orientation mechanisms are elucidated. Our observations advance the knowledge on key fundamental nanoscale mechanisms governing the dynamics of nanotubes and nanorods allowing bottom-up assembly into hierarchical superstructures.

cond-mat.soft↗

arXiv2018

Dynamic characterization of cellulose nanofibrils in sheared and extended semi-dilute dispersions

New materials made through controlled assembly of dispersed cellulose nanofibrils (CNF) has the potential to develop into biobased competitors to some of the highest performing materials today. The performance of these new cellulose materials depends on how easily CNF alignment can be controlled with hydrodynamic forces, which are always in competition with a different process driving the system towards isotropy, called rotary diffusion. In this work, we present a flow-stop experiment using polarized optical microscopy (POM) to study the rotary diffusion of CNF dispersions in process relevant flows and concentrations. This is combined with small angle X-ray scattering (SAXS) experiments to analyze the true orientation distribution function (ODF) of the flowing fibrils. It is found that the rotary diffusion process of CNF occurs at multiple time scales, where the fastest scale seems to be dependent on the deformation history of the dispersion before the stop. At the same time, the hypothesis that rotary diffusion is dependent on the initial ODF does not hold as the same distribution can result in different diffusion time scales. The rotary diffusion is found to be faster in flows dominated by shear compared to pure extensional flows. Furthermore, the experimental setup can be used to quickly characterize the dynamic properties of flowing CNF and thus aid in determining the quality of the dispersion and its usability in material processes.

cond-mat.soft↗

arXiv2017

Evaluating alignment of elongated nanoparticles in cylindrical geometries through small angle X-ray scattering experiments

The increased availability and brilliance of new X-ray facilities have in the recent years opened up the possibility to characterize the motion of dispersed nanoparticles in various microfluidic applications. One of these applications is the process of making strong continuous filaments through hydrodynamic alignment and assembly of cellulose nanofibrils (CNF) demonstrated by Håkansson et al. [Nature communications 5, 2014]. In this process it is vital to study the alignment of the nanofibrils in the flow, as this in turn affects the final material properties of the dried filament. Small angle X-ray scattering (SAXS) is a well-suited characterization technique for this, which typically provides the alignment in a projected plane perpendicular to the beam direction. In this work, we demonstrate a simple method to reconstruct the full three-dimensional (3D) orientation distribution function (ODF) from a SAXS-experiment through the assumption that the azimuthal angle of the nanofibril around the flow direction is distributed uniformly; an assumption that is approximately valid in the flow-focusing process. For demonstrational purposes, the experimental results from Håkansson et al. (2014) have been revised, resulting in a small correction to the presented order parameters. The results are then directly compared with simple numerical models to describe the increased alignment of CNF both in the flowing system and during the drying process. The proposed reconstruction method will allow for further improvements of theoretical or numerical simulations and consequently open up new possibilities for optimizing assembly processes, which include flow-alignment of elongated nanoparticles.

cond-mat.soft↗

arXiv2015

Experimental study of a three dimensional cylinder-filament system

This experimental study reports on the behavior of a filament attached to the rear of a three- dimensional cylinder. The axis of the cylinder is placed normal to a uniform incoming flow and the filament is free to move in the cylinder wake. The mean position of the filament is studied as a function of the filament length L. It is found that for long (L/D > 6.5, where D is the cylinder diameter) and short (L/D < 2) filaments the mean position of the filament tends to align with the incoming flow, whereas for intermediate filament lengths (2 < L/D < 6.5) the filament lies down on the cylinder and tends to align with the cylinder axis. The underlying mechanism of the bifurcations are discussed and related to buckling and inverted-pendulum-like instabilities.

physics.flu-dyn↗