arXiv subjects

David Emschermann

Publications and source records attributed to David Emschermann.

6 recordsLinked to original sources

arXiv2026

The Silicon Tracking System of the E16 experiment at J-PARC: construction, installation and commissioning in beam test experiments

The J-PARC E16 experiment aims to search for signatures of chiral symmetry restoration. It studies in-medium modifications of vector mesons that decay via the dielectron channel. The measurements use a high-intensity 30 GeV proton beam with C and Cu targets at rates up to 10 MHz. To achieve this, the experiment upgrades its tracking, by introducing innermost detector modules constructed with the same technology and procedures as the modules of the Silicon Tracking System (STS) of the Compressed Baryonic Matter (CBM) experiment at Facility for Antiproton and Ion Research (FAIR). A total of 15 modules were assembled, tested, characterized and then installed in the E16 detector setup. The detector was commissioned in a beam test experiment at Tsukuba, where the detector modules could be exposed to a 3 GeV electron beam. In preparation for the beam test the modules were characterized and calibrated, and performance studies were accomplished to assess the quality of the setup. During beamtime, three modules were operated and illuminated in two planes by the electron beam. This paper presents the results of the construction, characterization, commissioning, and operation of the E16-STS modules in beam test experiments.

physics.ins-det↗

arXiv2026

Performance of the Endcap Time-of-Flight detector in the STAR beam-energy scan

The STAR experiment at RHIC at Brookhaven National Laboratory completed the installation of an endcap time-of-flight subsystem (eTOF) in February 2019. The eTOF subsystem provided essential mid-rapidity particle identification (PID) for the fixed-target (FXT) portion of phase II of the beam energy scan (BES II). The FXT program allowed BES II to include center-of-mass energies from $\sqrt{s_{_{NN}}} = 3.0$ GeV to $\sqrt{s_{_{NN}}} = 7.7$ GeV, not accessible by colliding beams. The eTOF detectors and readout electronics were designed for the CBM experiment at FAIR and adapted for use at STAR. In this paper, we describe the details of the system in terms of geometrical layout, acceptance, calibration, hit reconstruction, and particle identification. The system achieved a time resolution of about 70 ps and a PID efficiency of about 70\%, meeting the design goals of the project.

physics.ins-det↗

arXiv2025

Testing a large size triple GEM detector for the first station of the CBM-Muon Chambers with a high-intensity gamma source at GIF++ under large-area illumination

The physics studies at heavy-ion nucleus-nucleus collision experiments demand reliable detectors at high particle flux. Therefore, Gas Electron Multipliers (GEM) detectors, which show resilience to extreme radiation, are one of the prime choices for the upcoming Compressed Baryonic Matter (CBM) experiment at the Facility of Antiproton and Ion Research, Germany. However, operating them under these demanding conditions requires a systemic study at the highest incident particle flux. To this end, we have conducted extensive tests on a real-size triple GEM detector module with the high-intensity gamma flux using the Cs-137 source at the upgraded Gamma Irradiation Facility (GIF++) at Conseil Europ\'een pour la Recherche Nucl\'eaire (CERN). The detector response, particularly regarding the gain and efficiency of muon detection, was studied extensively with and without a gamma source in a free-streaming mode using self-triggered electronics. This configuration will be necessary for the CBM experiment since it will observe unprecedented event rates of about 10 MHz for Au-Au collisions. The analysis reveals an alignment between the expected and observed value of gain and efficiency with an increasing intensity of gamma flux at the operating voltage. The test results demonstrate that the large-size GEM detector prototype can handle elevated gamma rates of approximately 17.25 MHz/cm2 without significantly impacting its performance or suffering irreversible damage.

hep-ex↗

arXiv2024

Evolution of the data aggregation concepts for STS readout in the CBM Experiment

The STS detector in the CBM experiment delivers data via multiple e-links connected to GBTX ASICs. In the process of data aggregation, that data must be received, combined into a smaller number of streams, and packed into so-called microslices containing data from specific periods. The aggregation must consider data randomization due to amplitude-dependent processing time in the FEE ASICs and different occupancy of individual e-links. During the development of the STS readout, the continued progress in the available technology affected the requirements for data aggregation, its architecture, and algorithms. The contribution presents considered solutions and discusses their properties.

physics.ins-det↗

arXiv2021

SMX and front-end board tester for CBM readout chain

The STS-MUCH-XYTER (SMX) chip is a front-end ASIC dedicated to the readout of Silicon Tracking System (STS) and Muon Chamber (MUCH) detectors in the Compressed Baryonic Matter (CBM) experiment. The production of the ASIC and the front-end boards based on it is just being started and requires thorough testing to assure quality. The paper describes the SMX tester based on a standard commercial Artix-7 FPGA module with an additional simple baseboard. In the standalone configuration, the tester is controlled via IPbus and enables full functional testing of connected SMX, front-end board (FEB), or a full detector module. The software written in Python may easily be integrated with higher-level testing software.

physics.ins-det↗

arXiv2021

GBTX emulator for development and special versions of GBT-based readout chains

The GBTX ASIC is a standard solution for providing fast control and data readout for radiation detectors used in HEP experiments. However, it is subject to export control restrictions due to the usage of radiation-hard technology. An FPGA-based GBTX emulator (GBTxEMU) has been developed to enable the development of GBT-based readout chains in countries where the original GBTX cannot be imported. Thanks to utilizing a slightly modified GBT-FGPA core, it maintains basic compatibility with standard GBT-based systems. The GBTxEMU also may be an interesting solution for developing GBT-based readout chains for less demanding experiments.

physics.ins-det↗