arXiv subjects

Andreas F. Molisch

Publications and source records attributed to Andreas F. Molisch.

At least 145 records · Page 8Linked to original sources

arXiv2014

Achievable Rates of FDD Massive MIMO Systems with Spatial Channel Correlation

It is well known that the performance of frequency-division-duplex (FDD) massive MIMO systems with i.i.d. channels is disappointing compared with that of time-division-duplex (TDD) systems, due to the prohibitively large overhead for acquiring channel state information at the transmitter (CSIT). In this paper, we investigate the achievable rates of FDD massive MIMO systems with spatially correlated channels, considering the CSIT acquisition dimensionality loss, the imperfection of CSIT and the regularized-zero-forcing linear precoder. The achievable rates are optimized by judiciously designing the downlink channel training sequences and user CSIT feedback codebooks, exploiting the multiuser spatial channel correlation. We compare our achievable rates with TDD massive MIMO systems, i.i.d. FDD systems, and the joint spatial division and multiplexing (JSDM) scheme, by deriving the deterministic equivalents of the achievable rates, based on popular channel models. It is shown that, based on the proposed eigenspace channel estimation schemes, the rate-gap between FDD systems and TDD systems is significantly narrowed, even approached under moderate number of base station antennas. Compared to the JSDM scheme, our proposal achieves dimensionality-reduction channel estimation without channel pre-projection, and higher throughput for moderate number of antennas and moderate to large channel coherence time, though at higher computational complexity.

cs.IT↗

arXiv2014

Max-Weight Scheduling and Quality-Aware Streaming for Device-to-Device Video Delivery

We propose and analyze centralized and distributed algorithms for device-to-device video scheduling and streaming. The proposed algorithms address jointly the problems of device-to-device link scheduling and video quality adaptation in streaming. Our simulations show that the proposed algorithms significantly outperform conventional separated approaches that treat these two problems independently.

cs.NI↗

arXiv2014

Joint Spatial Division and Multiplexing for mm-Wave Channels

Massive MIMO systems are well-suited for mm-Wave communications, as large arrays can be built with reasonable form factors, and the high array gains enable reasonable coverage even for outdoor communications. One of the main obstacles for using such systems in frequency-division duplex mode, namely the high overhead for the feedback of channel state information (CSI) to the transmitter, can be mitigated by the recently proposed JSDM (Joint Spatial Division and Multiplexing) algorithm. In this paper we analyze the performance of this algorithm in some realistic propagation channels that take into account the partial overlap of the angular spectra from different users, as well as the sparsity of mm-Wave channels. We formulate the problem of user grouping for two different objectives, namely maximizing spatial multiplexing, and maximizing total received power, in a graph-theoretic framework. As the resulting problems are numerically difficult, we proposed (sub optimum) greedy algorithms as efficient solution methods. Numerical examples show that the different algorithms may be superior in different settings.We furthermore develop a new, "degenerate" version of JSDM that only requires average CSI at the transmitter, and thus greatly reduces the computational burden. Evaluations in propagation channels obtained from ray tracing results, as well as in measured outdoor channels show that this low-complexity version performs surprisingly well in mm-Wave channels.

cs.IT↗

arXiv2014

Caching Eliminates the Wireless Bottleneck in Video-Aware Wireless Networks

Cellular data traffic almost doubles every year, greatly straining network capacity. The main driver for this development is wireless video. Traditional methods for capacity increase (like using more spectrum and increasing base station density) are very costly, and do not exploit the unique features of video, in particular a high degree of {\em asynchronous content reuse}. In this paper we give an overview of our work that proposed and detailed a new transmission paradigm exploiting content reuse, and the fact that storage is the fastest-increasing quantity in modern hardware. Our network structure uses caching in helper stations (femto-caching) and/or devices, combined with highly spectrally efficient short-range communications to deliver video files. For femto-caching, we develop optimum storage schemes and dynamic streaming policies that optimize video quality. For caching on devices, combined with device-to-device communications, we show that communications within {\em clusters} of mobile stations should be used; the cluster size can be adjusted to optimize the tradeoff between frequency reuse and the probability that a device finds a desired file cached by another device in the same cluster. We show that in many situations the network throughput increases linearly with the number of users, and that D2D communications also is superior in providing a better tradeoff between throughput and outage than traditional base-station centric systems. Simulation results with realistic numbers of users and channel conditions show that network throughput (possibly with outage constraints) can be increased by two orders of magnitude compared to conventional schemes.

cs.IT↗

arXiv2014

Fundamental Limits of Caching in Wireless D2D Networks

We consider a wireless Device-to-Device (D2D) network where communication is restricted to be single-hop. Users make arbitrary requests from a finite library of files and have pre-cached information on their devices, subject to a per-node storage capacity constraint. A similar problem has already been considered in an ``infrastructure'' setting, where all users receive a common multicast (coded) message from a single omniscient server (e.g., a base station having all the files in the library) through a shared bottleneck link. In this work, we consider a D2D ``infrastructure-less'' version of the problem. We propose a caching strategy based on deterministic assignment of subpackets of the library files, and a coded delivery strategy where the users send linearly coded messages to each other in order to collectively satisfy their demands. We also consider a random caching strategy, which is more suitable to a fully decentralized implementation. Under certain conditions, both approaches can achieve the information theoretic outer bound within a constant multiplicative factor. In our previous work, we showed that a caching D2D wireless network with one-hop communication, random caching, and uncoded delivery, achieves the same throughput scaling law of the infrastructure-based coded multicasting scheme, in the regime of large number of users and files in the library. This shows that the spatial reuse gain of the D2D network is order-equivalent to the coded multicasting gain of single base station transmission. It is therefore natural to ask whether these two gains are cumulative, i.e.,if a D2D network with both local communication (spatial reuse) and coded multicasting can provide an improved scaling law. Somewhat counterintuitively, we show that these gains do not cumulate (in terms of throughput scaling law).

cs.IT↗

arXiv2014

Time- and Frequency-Varying $K$-Factor of Non-Stationary Vehicular Channels for Safety Relevant Scenarios

Vehicular communication channels are characterized by a non-stationary time- and frequency-selective fading process due to fast changes in the environment. We characterize the distribution of the envelope of the first delay bin in vehicle-to-vehicle channels by means of its Rician $K$-factor. We analyze the time-frequency variability of this channel parameter using vehicular channel measurements at 5.6 GHz with a bandwidth of 240 MHz for safety-relevant scenarios in intelligent transportation systems (ITS). This data enables a frequency-variability analysis from an IEEE 802.11p system point of view, which uses 10 MHz channels. We show that the small-scale fading of the envelope of the first delay bin is Ricean distributed with a varying $K$-factor. The later delay bins are Rayleigh distributed. We demonstrate that the $K$-factor cannot be assumed to be constant in time and frequency. The causes of these variations are the frequency-varying antenna radiation patterns as well as the time-varying number of active scatterers, and the effects of vegetation. We also present a simple but accurate bi-modal Gaussian mixture model, that allows to capture the $K$-factor variability in time for safety-relevant ITS scenarios.

cs.NI↗

arXiv2014

Wireless Device-to-Device Caching Networks: Basic Principles and System Performance

As wireless video transmission is the fastest-growing form of data traffic, methods for spectrally efficient video on-demand wireless streaming are essential to service providers and users alike. A key property of video on-demand is the asynchronous content reuse, such that a few dominant videos account for a large part of the traffic, but are viewed by users at different times. Caching of content on devices in conjunction with D2D communications allows to exploit this property, and provide a network throughput that is significantly in excess of both the conventional approach of unicasting from the base station and the traditional D2D networks for regular data traffic. This paper presents in a semi-tutorial concise form some recent results on the throughput scaling laws of wireless networks with caching and asynchronous content reuse, contrasting the D2D approach with a competing approach based on combinatorial cache design and network coded transmission from the base station (BS) only, referred to as coded multicasting. Interestingly, the spatial reuse gain of the former and the coded multicasting gain of the latter yield, somehow surprisingly, the same near-optimal throughput behavior in the relevant regime where the number of video files in the library is smaller than the number of streaming users. Based on our recent theoretical results, we propose a holistic D2D system design that incorporates traditional microwave (2 GHz) as well as millimeter-wave D2D links; the direct connections to the base station can be used to provide those rare video requests that cannot be found in local caches. We provide extensive simulations under a variety of system settings, and compare our scheme with other existing schemes by the BS. We show that, despite the similar behavior of the scaling laws, the proposed D2D approach offers very significant throughput gains with respect to the BS-only schemes.

cs.IT↗

arXiv2013

FemtoCaching: Wireless Video Content Delivery through Distributed Caching Helpers

Video on-demand streaming from Internet-based servers is becoming one of the most important services offered by wireless networks today. In order to improve the area spectral efficiency of video transmission in cellular systems, small cells heterogeneous architectures (e.g., femtocells, WiFi off-loading) are being proposed, such that video traffic to nomadic users can be handled by short-range links to the nearest small cell access points (referred to as "helpers"). As the helper deployment density increases, the backhaul capacity becomes the system bottleneck. In order to alleviate such bottleneck we propose a system where helpers with low-rate backhaul but high storage capacity cache popular video files. Files not available from helpers are transmitted by the cellular base station. We analyze the optimum way of assigning files to the helpers, in order to minimize the expected downloading time for files. We distinguish between the uncoded case (where only complete files are stored) and the coded case, where segments of Fountain-encoded versions of the video files are stored at helpers. We show that the uncoded optimum file assignment is NP-hard, and develop a greedy strategy that is provably within a factor 2 of the optimum. Further, for a special case we provide an efficient algorithm achieving a provably better approximation ratio of $1-(1-1/d)^d$, where $d$ is the maximum number of helpers a user can be connected to. We also show that the coded optimum cache assignment problem is convex that can be further reduced to a linear program. We present numerical results comparing the proposed schemes.

cs.NI↗

arXiv2013

Diversity Backpressure Scheduling and Routing with Mutual Information Accumulation in Wireless Ad-hoc Networks

We suggest and analyze algorithms for routing in multi-hop wireless ad-hoc networks that exploit mutual information accumulation as the physical layer transmission scheme, and are capable of routing multiple packet streams (commodities) when only the average channel state information is present and that only locally. The proposed algorithms are modifications of the Diversity Backpressure (DIVBAR) algorithm, under which the packet whose commodity has the largest "backpressure metric" is chosen to be transmitted and is forwarded through the link with the largest differential backlog (queue length). In contrast to traditional DIVBAR, each receiving node stores and accumulates the partially received packet in a separate "partial packet queue", thus increasing the probability of successful reception during a later possible retransmission. We present two variants of the algorithm: DIVBAR-RMIA, under which all the receiving nodes clear the received partial information of a packet once one or more receiving nodes firstly decode the packet; and DIVBAR-MIA, under which all the receiving nodes retain the partial information of a packet until the packet has reached its destination. We characterize the network capacity region with RMIA and prove that (under certain mild conditions) it is strictly larger than the network capacity region with the repetition (REP) transmission scheme that is used by the traditional DIVBAR. We also prove that DIVBAR-RMIA is throughput-optimum among the polices with RMIA, i.e., it achieves the network capacity region with RMIA, which in turn demonstrates that DIVBAR-RMIA outperforms traditional DIVBAR on the achievable throughput. Moreover, we prove that DIVBAR-MIA performs at least as well as DIVBAR-RMIA with respect to throughput. Simulations also confirm these results.

cs.NI↗

arXiv2013

Optimal Throughput-Outage Trade-off in Wireless One-Hop Caching Networks

We consider a wireless device-to-device (D2D) network where the nodes have cached information from a library of possible files. Inspired by the current trend in the standardization of the D2D mode for 4th generation wireless networks, we restrict to one-hop communication: each node place a request to a file in the library, and downloads from some other node which has the requested file in its cache through a direct communication link, without going through a base station. We describe the physical layer communication through a simple "protocol-model", based on interference avoidance (independent set scheduling). For this network we define the outage-throughput tradeoff problem and characterize the optimal scaling laws for various regimes where both the number of nodes and the files in the library grow to infinity.

cs.IT↗

arXiv2013

Delay and Doppler Spreads of Non-Stationary Vehicular Channels for Safety Relevant Scenarios

Vehicular communication channels are characterized by a non-stationary time- and frequency-selective fading process due to rapid changes in the environment. The non-stationary fading process can be characterized by assuming local stationarity for a region with finite extent in time and frequency. For this finite region the wide-sense stationarity and uncorrelated-scattering (WSSUS) assumption holds approximately and we are able to calculate a time and frequency dependent local scattering function (LSF). In this paper, we estimate the LSF from a large set of measurements collected in the DRIVEWAY'09 measurement campaign, which focuses on scenarios for intelligent transportation systems. We then obtain the time-frequency-varying power delay profile (PDP) and the time-frequency-varying Doppler power spectral density (DSD) from the LSF. Based on the PDP and the DSD, we analyze the time-frequency-varying root mean square (RMS) delay spread and the RMS Doppler spread. We show that the distribution of these channel parameters follows a bi-modal Gaussian mixture distribution. High RMS delay spread values are observed in situations with rich scattering, while high RMS Doppler spreads are obtained in drive-by scenarios.

cs.NI↗

arXiv2013

Base-Station Assisted Device-to-Device Communications for High-Throughput Wireless Video Networks

We propose a new scheme for increasing the throughput of video files in cellular communications systems. This scheme exploits (i) the redundancy of user requests as well as (ii) the considerable storage capacity of smartphones and tablets. Users cache popular video files and - after receiving requests from other users - serve these requests via device-to-device localized transmissions. The file placement is optimal when a central control knows a priori the locations of wireless devices when file requests occur. However, even a purely random caching scheme shows only a minor performance loss compared to such a genie-aided scheme. We then analyze the optimal collaboration distance, trading off frequency reuse with the probability of finding a requested file within the collaboration distance. We show that an improvement of spectral efficiency of one to two orders of magnitude is possible, even if there is not very high redundancy in video requests.

cs.NI↗

arXiv2013

Fundamental Limits of Distributed Caching in D2D Wireless Networks

We consider a wireless Device-to-Device (D2D) network where communication is restricted to be single-hop, users make arbitrary requests from a finite library of possible files and user devices cache information in the form of linear combinations of packets from the files in the library (coded caching). We consider the combined effect of coding in the caching and delivery phases, achieving "coded multicast gain", and of spatial reuse due to local short-range D2D communication. Somewhat counterintuitively, we show that the coded multicast gain and the spatial reuse gain do not cumulate, in terms of the throughput scaling laws. In particular, the spatial reuse gain shown in our previous work on uncoded random caching and the coded multicast gain shown in this paper yield the same scaling laws behavior, but no further scaling law gain can be achieved by using both coded caching and D2D spatial reuse.

cs.IT↗

arXiv2013

Quality-Aware Coding and Relaying for 60 GHz Real-Time Wireless Video Broadcasting

Wireless streaming of high-definition video is a promising application for 60 GHz links, since multi-Gigabit/s data rates are possible. In particular we consider a sports stadium broadcasting system where video signals from multiple cameras are transmitted to a central location. Due to the high pathloss of 60\,GHz radiation over the large distances encountered in this setting, the use of relays is required. This paper designs a quality-aware coding and relaying algorithm for maximization of the overall video quality. We consider the setting that the source can split its data stream into parallel streams, which can be transmitted via different relays to the destination. For this, we derive the related formulation and re-formulate it as convex programming, which can guarantee optimal solutions.

cs.NI↗

arXiv2013

Joint Scalable Coding and Routing for 60 GHz Real-Time Live HD Video Streaming Applications

Transmission of high-definition (HD) video is a promising application for 60 GHz wireless links, since very high transmission rates (up to several Gbit/s) are possible. In particular we consider a sports stadium broadcasting system where signals from multiple cameras are transmitted to a central location. Due to the high pathloss of 60 GHz radiation over the large distances encountered in this scenario, the use of relays might be required. The current paper analyzes the joint selection of the routes (relays) and the compression rates from the various sources for maximization of the overall video quality. We consider three different scenarios: (i) each source transmits only to one relay and the relay can receive only one data stream, and (ii) each source can transmit only to a single relay, but relays can aggregate streams from different sources and forward to the destination, and (iii) the source can split its data stream into parallel streams, which can be transmitted via different relays to the destination. For each scenario, we derive the mathematical formulations of the optimization problem and re-formulate them as convex mixed-integer programming, which can guarantee optimal solutions. Extensive simulations demonstrate that high-quality transmission is possible for at least ten cameras over distances of 300 m. Furthermore, optimization of the video quality gives results that can significantly outperform algorithms that maximize data rates.

cs.NI↗

arXiv2012

Scaling Behaviors of Wireless Device-to-Device Communications with Distributed Caching

We analyze a novel architecture for caching popular video content to enable wireless device-to-device collaboration. We focus on the asymptotic scaling characteristics and show how they depends on video content popularity statistics. We identify a fundamental conflict between collaboration distance and interference and show how to optimize the transmission power to maximize frequency reuse. Our main result is a closed form expression of the optimal collaboration distance as a function of the model parameters. Under the common assumption of a Zipf distribution for content reuse, we show that if the Zipf exponent is greater than 1, it is possible to have a number of D2D interference-free collaboration pairs that scales linearly in the number of nodes. If the Zipf exponent is smaller than 1, we identify the best possible scaling in the number of D2D collaborating links. Surprisingly, a very simple distributed caching policy achieves the optimal scaling behavior and therefore there is no need to centrally coordinate what each node is caching.

cs.NI↗

arXiv2012

Wireless Device-to-Device Communications with Distributed Caching

We introduce a novel wireless device-to-device (D2D) collaboration architecture that exploits distributed storage of popular content to enable frequency reuse. We identify a fundamental conflict between collaboration distance and interference and show how to optimize the transmission power to maximize frequency reuse. Our analysis depends on the user content request statistics which are modeled by a Zipf distribution. Our main result is a closed form expression of the optimal collaboration distance as a function of the content reuse distribution parameters. We show that if the Zipf exponent of the content reuse distribution is greater than 1, it is possible to have a number of D2D interference-free collaboration pairs that scales linearly in the number of nodes. If the Zipf exponent is smaller than 1, we identify the best possible scaling in the number of D2D collaborating links. Surprisingly, a very simple distributed caching policy achieves the optimal scaling behavior and therefore there is no need to centrally coordinate what each node is caching.

cs.IT↗

arXiv2012

Energy-Delay Tradeoff and Dynamic Sleep Switching for Bluetooth-Like Body-Area Sensor Networks

Wireless technology enables novel approaches to healthcare, in particular the remote monitoring of vital signs and other parameters indicative of people's health. This paper considers a system scenario relevant to such applications, where a smart-phone acts as a data-collecting hub, gathering data from a number of wireless-capable body sensors, and relaying them to a healthcare provider host through standard existing cellular networks. Delay of critical data and sensors' energy efficiency are both relevant and conflicting issues. Therefore, it is important to operate the wireless body-area sensor network at some desired point close to the optimal energy-delay tradeoff curve. This tradeoff curve is a function of the employed physical-layer protocol: in particular, it depends on the multiple-access scheme and on the coding and modulation schemes available. In this work, we consider a protocol closely inspired by the widely-used Bluetooth standard. First, we consider the calculation of the minimum energy function, i.e., the minimum sum energy per symbol that guarantees the stability of all transmission queues in the network. Then, we apply the general theory developed by Neely to develop a dynamic scheduling policy that approaches the optimal energy-delay tradeoff for the network at hand. Finally, we examine the queue dynamics and propose a novel policy that adaptively switches between connected and disconnected (sleeping) modes. We demonstrate that the proposed policy can achieve significant gains in the realistic case where the control "NULL" packets necessary to maintain the connection alive, have a non-zero energy cost, and the data arrival statistics corresponding to the sensed physical process are bursty.

cs.IT↗