arXiv Science⌕ Search

arXiv subjects

Zhichao Liu

Publications and source records attributed to Zhichao Liu.

72 records · Page 4Linked to original sources
arXiv2022

Closed-loop Position Control of a Pediatric Soft Robotic Wearable Device for Upper Extremity Assistance

This work focuses on closed-loop control based on proprioceptive feedback for a pneumatically-actuated soft wearable device aimed at future support of infant reaching tasks. The device comprises two soft pneumatic actuators (one textile-based and one silicone-casted) actively controlling two degrees-of-freedom per arm (shoulder adduction/abduction and elbow flexion/extension, respectively). Inertial measurement units (IMUs) attached to the wearable device provide real-time joint angle feedback. Device kinematics analysis is informed by anthropometric data from infants (arm lengths) reported in the literature. Range of motion and muscle co-activation patterns in infant reaching are considered to derive desired trajectories for the device's end-effector. Then, a proportional-derivative controller is developed to regulate the pressure inside the actuators and in turn move the arm along desired setpoints within the reachable workspace. Experimental results on tracking desired arm trajectories using an engineered mannequin are presented, demonstrating that the proposed controller can help guide the mannequin's wrist to the desired setpoints.

cs.RO↗
arXiv2022

Automatic spinal curvature measurement on ultrasound spine images using Faster R-CNN

Ultrasound spine imaging technique has been applied to the assessment of spine deformity. However, manual measurements of scoliotic angles on ultrasound images are time-consuming and heavily rely on raters experience. The objectives of this study are to construct a fully automatic framework based on Faster R-CNN for detecting vertebral lamina and to measure the fitting spinal curves from the detected lamina pairs. The framework consisted of two closely linked modules: 1) the lamina detector for identifying and locating each lamina pairs on ultrasound coronal images, and 2) the spinal curvature estimator for calculating the scoliotic angles based on the chain of detected lamina. Two hundred ultrasound images obtained from AIS patients were identified and used for the training and evaluation of the proposed method. The experimental results showed the 0.76 AP on the test set, and the Mean Absolute Difference (MAD) between automatic and manual measurement which was within the clinical acceptance error. Meanwhile the correlation between automatic measurement and Cobb angle from radiographs was 0.79. The results revealed that our proposed technique could provide accurate and reliable automatic curvature measurements on ultrasound spine images for spine deformities.

eess.IV↗
arXiv2022

Human-Object Interaction Detection via Disentangled Transformer

Human-Object Interaction Detection tackles the problem of joint localization and classification of human object interactions. Existing HOI transformers either adopt a single decoder for triplet prediction, or utilize two parallel decoders to detect individual objects and interactions separately, and compose triplets by a matching process. In contrast, we decouple the triplet prediction into human-object pair detection and interaction classification. Our main motivation is that detecting the human-object instances and classifying interactions accurately needs to learn representations that focus on different regions. To this end, we present Disentangled Transformer, where both encoder and decoder are disentangled to facilitate learning of two sub-tasks. To associate the predictions of disentangled decoders, we first generate a unified representation for HOI triplets with a base decoder, and then utilize it as input feature of each disentangled decoder. Extensive experiments show that our method outperforms prior work on two public HOI benchmarks by a sizeable margin. Code will be available.

cs.CV↗
arXiv2021

Phonon-laser ultrasensitive force sensor

Developing nano-mechanical oscillators for ultrasensitive force detection is of great importance in exploring science. We report our achievement of ultrasensitive detection of the external force regarding the radio-frequency electric field by a nano-sensor made of a single trapped $^{40}$Ca$^{+}$ ion under injection-locking, where squeezing is additionally applied to detection of the smallest force in the ion trap. The employed ion is confined stably in a surface electrode trap and works as a phonon laser that is very sensitive to the external disturbance. The injection-locking drove the ion's oscillation with phase synchronization, yielding the force detection with sensitivity of 347 $\pm$ 50 yN/$\sqrt{Hz}$. Further with 3 dB squeezing applied on the oscillation phase variance, we achieved a successful detection of the smallest force to be 86.5 $\pm$ 70.1 yN.

quant-ph↗
arXiv2021

Initial energy deposition and initiation mechanism of nanosecond laser damage caused by KDP surface micro-defects

To enable an exploration of the initiation mechanism of nanosecond laser damage on a potassium dihydrogen phosphate (KDP) surface, a defect-assisted energy deposition model is developed that involves light intensity enhancement and a sub-band gap energy level structure. The simulations provide an explanation on why the laser-induced damage threshold (LIDT) of the KDP crystal is two orders of magnitude lower than the theoretical value. The model is verified by use of the transient images that appear during the laser damage. In addition, the dimensions of the "dangerous" surface defects that are the most sensitive to the laser damage are proposed. This work enables clarification on the initial energy deposition (IED) and initiation mechanism of the nanosecond laser damage caused by the KDP surface defects on micro-nano scale. It is helpful in understanding the laser-matter interactions and to improve the processing technique for high quality optical components.

physics.app-ph↗
arXiv2021

Deformation Recovery Control and Post-Impact Trajectory Replanning for Collision-Resilient Mobile Robots

The paper focuses on collision-inclusive motion planning for impact-resilient mobile robots. We propose a new deformation recovery and replanning strategy to handle collisions that may occur at run-time. Contrary to collision avoidance methods that generate trajectories only in conservative local space or require collision checking that has high computational cost, our method directly generates (local) trajectories with imposing only waypoint constraints. If a collision occurs, our method then estimates the post-impact state and computes from there an intermediate waypoint to recover from the collision. To achieve so, we develop two novel components: 1) a deformation recovery controller that optimizes the robot's states during post-impact recovery phase, and 2) a post-impact trajectory replanner that adjusts the next waypoint with the information from the collision for the robot to pass through and generates a polynomial-based minimum effort trajectory. The proposed strategy is evaluated experimentally with an omni-directional impact-resilient wheeled robot. The robot is designed in house, and it can perceive collisions with the aid of Hall effect sensors embodied between the robot's main chassis and a surrounding deflection ring-like structure.

cs.RO↗
arXiv2021

Position Control and Variable-Height Trajectory Tracking of a Soft Pneumatic Legged Robot

Soft pneumatic legged robots show promise in their ability to traverse a range of different types of terrain, including natural unstructured terrain met in applications like precision agriculture. They can adapt their body morphology to the intricacies of the terrain at hand, thus enabling robust and resilient locomotion. In this paper we capitalize upon recent developments on soft pneumatic legged robots to introduce a closed-loop trajectory tracking control scheme for operation over flat ground. Closed-loop pneumatic actuation feedback is achieved via a compact and portable pneumatic regulation board. Experimental results reveal that our soft legged robot can precisely control its body height and orientation while in quasi-static operation based on a geometric model. The robot can track both straight line and curved trajectories as well as variable-height trajectories. This work lays the basis to enable autonomous navigation for soft legged robots.

cs.RO↗
arXiv2021

Toward Impact-resilient Quadrotor Design, Collision Characterization and Recovery Control to Sustain Flight after Collisions

Collision detection and recovery for aerial robots remain a challenge because of the limited space for sensors and local stability of the flight controller. We introduce a novel collision-resilient quadrotor that features a compliant arm design to enable free flight while allowing for one passive degree of freedom to absorb shocks. We further propose a novel collision detection and characterization method based on Hall sensors, as well as a new recovery control method to generate and track a smooth trajectory after a collision occurs. Experimental results demonstrate that the robot can detect and recover from high-speed collisions with various obstacles such as walls and poles. Moreover, it can survive collisions that are hard to detect with existing methods based on IMU data and contact models, for example, when colliding with unstructured surfaces, or being hit by a moving obstacle while hovering.

cs.RO↗
arXiv2020

Motion Planning for Collision-resilient Mobile Robots in Obstacle-cluttered Unknown Environments with Risk Reward Trade-offs

Collision avoidance in unknown obstacle-cluttered environments may not always be feasible. This paper focuses on an emerging paradigm shift in which potential collisions with the environment can be harnessed instead of being avoided altogether. To this end, we introduce a new sampling-based online planning algorithm that can explicitly handle the risk of colliding with the environment and can switch between collision avoidance and collision exploitation. Central to the planner's capabilities is a novel joint optimization function that evaluates the effect of possible collisions using a reflection model. This way, the planner can make deliberate decisions to collide with the environment if such collision is expected to help the robot make progress toward its goal. To make the algorithm online, we present a state expansion pruning technique that significantly reduces the search space while ensuring completeness. The proposed algorithm is evaluated experimentally with a built-in-house holonomic wheeled robot that can withstand collisions. We perform an extensive parametric study to investigate trade-offs between (user-tuned) levels of risk, deliberate collision decision making, and trajectory statistics such as time to reach the goal and path length.

cs.RO↗
arXiv2020

Application of light diffraction theory to qualify the downstream light field modulation property of mitigated KDP crystals

Micro-milling can effectively remove laser damage sites on a KDP (potassium dihydrogen phosphate) surface and then improve the laser damage resistance of the components. However, the repaired KDP surface could cause light propagating turbulence and downstream light intensification with the potential risk to damage downstream optics. In order to analyze the downstream light field modulation caused by Gaussian mitigation pits on KDP crystals, a computational model of the downstream light diffraction based on the angular spectrum theory and the Gaussian repair contour is established. The results show that the phase offset caused by the repaired surface produces a large light field modulation near the rear KDP surface. The modulation generated in the whole downstream light field is greater than that caused by the amplitude change. Therefore, the phase characteristics of the outgoing light could be suggested as a vital research topic for future research on the downstream light field modulation caused by mitigation contours. Significantly, the experimental results on the downstream light intensity distribution have good agreement with the simulation ones, which proves the validity of the established downstream light diffraction model. The phase characterization of the outgoing light is proposed as an evaluation tool in the repair of KDP crystals. The developed analytical method and numerical discrete algorithm could be also applicable in qualifying the repair quality of other optical components applied in high-power laser systems.

physics.optics↗
arXiv2019

Stable homotopy, 1-dimensional NCCW complexes, and Property (H)

In this paper, we show that the homomorphisms between two unital one-dimensional NCCW complexes with the same KK-class are stably homotopic, i.e., with adding on a common homomorphism (with finite dimensional image), they are homotopic. As a consequence, any one-dimensional NCCW complex has the Property (H).

math.OA↗
arXiv2019

DS-VIO: Robust and Efficient Stereo Visual Inertial Odometry based on Dual Stage EKF

This paper presents a dual stage EKF (Extended Kalman Filter)-based algorithm for the real-time and robust stereo VIO (visual inertial odometry). The first stage of this EKF-based algorithm performs the fusion of accelerometer and gyroscope while the second performs the fusion of stereo camera and IMU. Due to the sufficient complementary characteristics between accelerometer and gyroscope as well as stereo camera and IMU, the dual stage EKF-based algorithm can achieve a high precision of odometry estimations. At the same time, because of the low dimension of state vector in this algorithm, its computational efficiency is comparable to previous filter-based approaches. We call our approach DS-VIO (dual stage EKFbased stereo visual inertial odometry) and evaluate our DSVIO algorithm by comparing it with the state-of-art approaches including OKVIS, ROVIO, VINS-MONO and S-MSCKF on the EuRoC dataset. Results show that our algorithm can achieve comparable or even better performances in terms of the RMS error

cs.CV↗
arXiv2018

Injectivity of the connecting homomorphisms

Let $A$ be the inductive limit of a sequence $$A_1\, \xrightarrow{ϕ_{1,2}} \,A_2\,\xrightarrow{ϕ_{2,3}} \,A_3\rightarrow\cdots$$ with $A_n=\oplus_{i=1}^{n_i}A_{[n,i]}$, where all the $A_{[n,i]}$ are Elliott-Thomsen algebras and $ϕ_{n,n+1}$ are homomorphisms, in this paper, we will prove that $A$ can be written as another inductive limit $$B_1\,\xrightarrow{ψ_{1,2}} \,B_2\,\xrightarrow{ψ_{2,3}} \,B_3\rightarrow\cdots$$ with $B_n=\oplus_{i=1}^{n_i}B_{[n,i]}$, where all the $B_{[n,i]}$ are Elliott-Thomsen building blocks and with the extra condition that all the $ϕ_{n,n+1}$ are injective.

math.OA↗
arXiv2017

A Robust Bayesian Exponentially Tilted Empirical Likelihood Method

This paper proposes a new Bayesian approach for analysing moment condition models in the situation where the data may be contaminated by outliers. The approach builds upon the foundations developed by Schennach (2005) who proposed the Bayesian exponentially tilted empirical likelihood (BETEL) method, justified by the fact that an empirical likelihood (EL) can be interpreted as the nonparametric limit of a Bayesian procedure when the implied probabilities are obtained from maximizing entropy subject to some given moment constraints. Considering the impact that outliers are thought to have on the estimation of population moments, we develop a new robust BETEL (RBETEL) inferential methodology to deal with this potential problem. We show how the BETEL methods are linked to the recent work of Bissiri, Holmes and Walker (2016) who propose a general framework to update prior belief via a loss function. A controlled simulation experiment is conducted to investigate the performance of the RBETEL method. We find that the proposed methodology produces reliable posterior inference for the fundamental relationships that are embedded in the majority of the data, even when outliers are present. The method is also illustrated in an empirical study relating brain weight to body weight using a dataset containing sixty-five different land animal species.

stat.ME↗
arXiv2017

SRPGAN: Perceptual Generative Adversarial Network for Single Image Super Resolution

Single image super resolution (SISR) is to reconstruct a high resolution image from a single low resolution image. The SISR task has been a very attractive research topic over the last two decades. In recent years, convolutional neural network (CNN) based models have achieved great performance on SISR task. Despite the breakthroughs achieved by using CNN models, there are still some problems remaining unsolved, such as how to recover high frequency details of high resolution images. Previous CNN based models always use a pixel wise loss, such as l2 loss. Although the high resolution images constructed by these models have high peak signal-to-noise ratio (PSNR), they often tend to be blurry and lack high-frequency details, especially at a large scaling factor. In this paper, we build a super resolution perceptual generative adversarial network (SRPGAN) framework for SISR tasks. In the framework, we propose a robust perceptual loss based on the discriminator of the built SRPGAN model. We use the Charbonnier loss function to build the content loss and combine it with the proposed perceptual loss and the adversarial loss. Compared with other state-of-the-art methods, our method has demonstrated great ability to construct images with sharp edges and rich details. We also evaluate our method on different benchmarks and compare it with previous CNN based methods. The results show that our method can achieve much higher structural similarity index (SSIM) scores on most of the benchmarks than the previous state-of-art methods.

cs.CV↗