arXiv subjects

Yumin Su

Publications and source records attributed to Yumin Su.

6 recordsLinked to original sources

arXiv2026

A Magnon-Based Electric Field Controlled Magnetoelectric Device for Energy-Efficient Logic-in-Memory

We demonstrate a non-volatile magnetoelectric magnonic memory (MEMM) that enables fully electrical write/read via direct magnon-driven sensing in an insulating antiferromagnet. A fabricated SrIrO3/La-BiFeO3/SrIrO3 trilayer exhibits sub-100 ps switching, a remnant polarization of 20 uC/cm2, and a readout voltage contrast close to 1mV between high and low-resistance states. To connect device physics to circuit behavior, we develop and experimentally validate a compact circuit model that captures spin Hall injection and spin transport. Simulations with optimized material parameters predict output voltages > 100mV, enabling cascading without external amplification. Using this framework, we design MEMM-based memory and logic blocks, including a 1T1R array, two inverter implementations (complementary two-device and single-device), and a three-input majority gate, and evaluate deep-pipelined operation. The model projects switching energies down to 1 aJ per operation and logic propagation delays of 30-60 ps, indicating MEMM as a promising platform for energy-constrained, high throughput computing.

cond-mat.mtrl-sci↗

arXiv2026

An Efficient Power Management Unit With Continuous MPPT and Energy Recycling for Wireless Millimetric Biomedical Implants

Biomedical implants offer transformative tools to improve medical outcomes. To realize minimally invasive implants with miniaturized volume and weight, wireless power transfer has been extensively studied to replace bulky batteries that dominate the volume of traditional implants and require surgical replacements. Ultra-sonic and magnetoelectric WPT modalities, which leverage low frequency acoustic electrical coupling for energy transduction, become viable solutions for mm-scale receivers. This work presents a fully integrated power management unit for ME WPT in millimetric implants. The PMU achieves load independent maximum power extraction and usage by continuously matching the impedance of the transducer, dynamically optimizing the power stage across varying input divided by load conditions, and reusing the storage energy to sustain the system when input power drops. Its parallel-input regulation and storing stages architecture prevent the cascading power loss. With the skewed-duty-cycle MPPT technique and regulation efficiency optimizer, the PMU achieves a peak MPPT efficiency of 98.5 percent and a peak system overall efficiency of 73.33 percent. Additionally, the PMU includes an adaptive high-voltage charging stage that charges the stimulation capacitor up to 12 V with an improved efficiency of 37.88 percent.

eess.SY↗

arXiv2026

PowerGenie: Analytically-Guided Evolutionary Discovery of Superior Reconfigurable Power Converters

Discovering superior circuit topologies requires navigating an exponentially large design space-a challenge traditionally reserved for human experts. Existing AI methods either select from predefined templates or generate novel topologies at a limited scale without rigorous verification, leaving large-scale performance-driven discovery underexplored. We present PowerGenie, a framework for automated discovery of higher-performance reconfigurable power converters at scale. PowerGenie introduces: (1) an automated analytical framework that determines converter functionality and theoretical performance limits without component sizing or SPICE simulation, and (2) an evolutionary finetuning method that co-evolves a generative model with its training distribution through fitness selection and uniqueness verification. Unlike existing methods that suffer from mode collapse and overfitting, our approach achieves higher syntax validity, function validity, novelty rate, and figure-of-merit (FoM). PowerGenie discovers a novel 8-mode reconfigurable converter with 23% higher FoM than the best training topology. SPICE simulations confirm average absolute efficiency gains of 10% across 8 modes and up to 17% at a single mode. Code will be released upon publication.

cs.LG↗

arXiv2025

Compressive Sensing Photoacoustic Imaging Receiver with Matrix-Vector-Multiplication SAR ADC

Wearable photoacoustic imaging devices hold great promise for continuous health monitoring and point-of-care diagnostics. However, the large data volume generated by high-density transducer arrays presents a major challenge for realizing compact and power-efficient wearable systems. This paper presents a photoacoustic imaging receiver (RX) that embeds compressive sensing directly into the hardware to address this bottleneck. The RX integrates 16 AFEs and four matrix-vector-multiplication (MVM) SAR ADCs that perform energy- and area-efficient analog-domain compression. The architecture achieves a 4-8x reduction in output data rate while preserving low-loss full-array information. The MVM SAR ADC executes passive and accurate MVM using user-defined programmable ternary weights. Two signal reconstruction methods are implemented: (1) an optimization approach using the fast iterative shrinkage-thresholding algorithm, and (2) a learning-based approach employing implicit neural representation. Fabricated in 65 nm CMOS, the chip achieves an ADC's SNDR of 57.5 dB at 20.41 MS/s, with an AFE input-referred noise of 3.5 nV/sqrt(Hz). MVM linearity measurements show R^2 > 0.999 across a wide range of weights and input amplitudes. The system is validated through phantom imaging experiments, demonstrating high-fidelity image reconstruction under up to 8x compression. The RX consumes 5.83 mW/channel and supports a general ternary-weighted measurement matrix, offering a compelling solution for next-generation miniaturized, wearable PA imaging systems.

eess.IV↗

arXiv2025

Design-Agnostic Distributed Timing Fault Injection Monitor With End-to-End Design Automation

Fault injection attacks induce hardware failures in circuits and exploit these faults to compromise the security of the system. It has been demonstrated that FIAs can bypass system security mechanisms, cause faulty outputs, and gain access to secret information. Certain types of FIAs can be mounted with little effort by tampering with clock signals and or the chip operating conditions. To mitigate such low cost, yet powerful attacks, we propose a fully synthesizable and distributable in situ fault injection monitor that employs a delay locked loop to track the pulsewidth of the clock. We further develop a fully automated design framework to optimize and implement the FIA monitors at any process node. Our design is fabricated and verified in 65 nm CMOS technology with a small footprint of 1500 um2. It can lock to clock frequencies from 2 MHz to 1.26 GHz while detecting all 12 types of possible clock glitches, as well as timing FIA injections via the supply voltage, electromagnetic signals, and chip temperature.

eess.SY↗

arXiv2024

Omnidirectional Wireless Power Transfer for Millimetric Magnetoelectric Biomedical Implants

Miniature bioelectronic implants promise revolutionary therapies for cardiovascular and neurological disorders. Wireless power transfer (WPT) is a significant method for miniaturization, eliminating the need for bulky batteries in devices. Despite successful demonstrations of millimetric battery free implants in animal models, the robustness and efficiency of WPT are known to degrade significantly under misalignment incurred by body movements, respiration, heart beating, and limited control of implant orientation during surgery. This article presents an omnidirectional WPT platform for millimetric bioelectronic implants, employing the emerging magnetoelectric (ME) WPT modality, and magnetic field steering technique based on multiple transmitter (TX) coils. To accurately sense the weak coupling in a miniature implant and adaptively control the multicoil TX array in a closed loop, we develop an active echo (AE) scheme using a tiny coil on the implant. Our prototype comprises a fully integrated 14.2 mm3 implantable stimulator embedding a custom low power system on chip (SoC) powered by an ME film, a TX with a custom three channel AE RX chip, and a multicoil TX array with mutual inductance cancellation. The AE RX achieves negative 161 dBm per Hz input referred noise with 64 dB gain tuning range to reliably sense the AE signal, and offers fast polarity detection for driver control. AE simultaneously enhances the robustness, efficiency, and charging range of ME WPT. Under 90 degree rotation from the ideal position, our omnidirectional WPT system achieves 6.8x higher power transfer efficiency (PTE) than a single coil baseline. The tracking error of AE negligibly degrades the PTE by less than 2 percent from using ideal control.

eess.SY↗