arXiv subjects

Wei Tech Ang

Publications and source records attributed to Wei Tech Ang.

14 recordsLinked to original sources

arXiv2026

Beyond Heuristics: A Standardized Real2Sim Pipeline for Physical Human Robot Interaction in Human-in-the-Loop Simulation

The aging global population drives demand for assistive robots, yet the safety risks and costs of physical testing make Human-in-the-Loop (HITL) simulation an attractive alternative. Its fidelity for coupled systems, however, is limited by interaction models whose impedance parameters are tuned heuristically rather than identified from data. We present a Real2Sim pipeline that identifies the coupled Physical Human-Robot Interaction (pHRI) dynamics of a pelvis--strap interface on an overground mobile balance assistant. The interface is modeled as a 6-DoF viscoelastic mechanism whose 12 directional stiffness and damping parameters are identified per subject via Covariance Matrix Adaptation Evolution Strategy (CMA-ES), using the user's ``Safe \& Comfortable'' feedback as a reproducible operating point that resolves harness-tightness ambiguity across anthropometrics. An intraclass-correlation analysis over a five-subject cohort separates shareable from subject-specific parameters, yielding a set of prior parameters derived from the existing data. Deploying this prior configures a previously unseen subject by refining only 5 of the 12 parameters. The calibrated model then reproduces the real interaction envelope and induces biomechanically accurate gait adaptations in the Human Digital Twin (HDT). Overly compliant and overly stiff settings, by contrast, fail as extreme settings, confirming a correct operating point that no heuristic tuning procedure can reliably select. The pipeline thus improves HITL simulation fidelity and supports the Human Digital Twin as a predictive tool for pre-clinical verification of personalized controllers.

cs.RO↗

arXiv2026

DRBA: Dynamic Robotic Balance Assistant -- An assist-as-needed gait and balance rehabilitation robot for versatile training

The decline of human balance control due to aging and pathological conditions increases fall risk, a major concern in geriatric care and rehabilitation. Gait training is essential for balance recovery, enhancing walking ability and postural control. However, existing overground robotic gait trainers have limitations: body weight support systems are bulky and impractical for daily use, while end-effector-based systems often compromise transparency, altering natural gait dynamics. This paper presents the Dynamic Robotic Balance Assistant (DRBA), a novel gait trainer providing assist-as-needed body weight and balance support for various training scenarios. DRBA integrates a 3-degree-of-freedom (3-DoF) robotic arm for pelvic support with flexible motion, a compact sit-to-stand assistance module, and user-following and fall detection algorithms to ensure minimal interference and responsive support. Experimental results demonstrated high transparency, with minimal impact on natural gait dynamics. A patient trial with nine elderly patients with varying medical conditions and balance impairments (ranging from severe to mild) further validated DRBA's effectiveness. The results showed that DRBA-assisted training increased step length and walking speed compared to therapist-assisted gait training. Additionally, DRBA enabled users to perform tasks beyond their unaided ability, expanding rehabilitation possibilities. These findings highlight DRBA's potential to enhance rehabilitation outcomes by facilitating higher training intensity and enabling task-oriented exercises.

cs.RO↗

arXiv2025

A Human-In-The-Loop Simulation Framework for Evaluating Control Strategies in Gait Assistive Robots

As the global population ages, effective rehabilitation and mobility aids will become increasingly critical. Gait assistive robots are promising solutions, but designing adaptable controllers for various impairments poses a significant challenge. This paper presented a Human-In-The-Loop (HITL) simulation framework tailored specifically for gait assistive robots, addressing unique challenges posed by passive support systems. We incorporated a realistic physical human-robot interaction (pHRI) model to enable a quantitative evaluation of robot control strategies, highlighting the performance of a speed-adaptive controller compared to a conventional PID controller in maintaining compliance and reducing gait distortion. We assessed the accuracy of the simulated interactions against that of the real-world data and revealed discrepancies in the adaptation strategies taken by the human and their effect on the human's gait. This work underscored the potential of HITL simulation as a versatile tool for developing and fine-tuning personalized control policies for various users.

cs.RO↗

arXiv2025

Detecting Heel Strike and toe off Events Using Kinematic Methods and LSTM Models

Accurate gait event detection is crucial for gait analysis, rehabilitation, and assistive technology, particularly in exoskeleton control, where precise identification of stance and swing phases is essential. This study evaluated the performance of seven kinematics-based methods and a Long Short-Term Memory (LSTM) model for detecting heel strike and toe-off events across 4363 gait cycles from 588 able-bodied subjects. The results indicated that while the Zeni et al. method achieved the highest accuracy among kinematics-based approaches, other methods exhibited systematic biases or required dataset-specific tuning. The LSTM model performed comparably to Zeni et al., providing a data-driven alternative without systematic bias. These findings highlight the potential of deep learning-based approaches for gait event detection while emphasizing the need for further validation in clinical populations and across diverse gait conditions. Future research will explore the generalizability of these methods in pathological populations, such as individuals with post-stroke conditions and knee osteoarthritis, as well as their robustness across varied gait conditions and data collection settings to enhance their applicability in rehabilitation and exoskeleton control.

cs.RO↗

arXiv2025

Simulating Safe Bite Transfer in Robot-Assisted Feeding with a Soft Head and Articulated Jaw

Ensuring safe and comfortable bite transfer during robot-assisted feeding is challenging due to the close physical human-robot interaction required. This paper presents a novel approach to modeling physical human-robot interaction in a physics-based simulator (MuJoCo) using soft-body dynamics. We integrate a flexible head model with a rigid skeleton while accounting for internal dynamics, enabling the flexible model to be actuated by the skeleton. Incorporating realistic soft-skin contact dynamics in simulation allows for systematically evaluating bite transfer parameters, such as insertion depth and entry angle, and their impact on user safety and comfort. Our findings suggest that a straight-in-straight-out strategy minimizes forces and enhances user comfort in robot-assisted feeding, assuming a static head. This simulation-based approach offers a safer and more controlled alternative to real-world experimentation. Supplementary videos can be found at: https://tinyurl.com/224yh2kx.

cs.RO↗

arXiv2025

Design of a Breakaway Utensil Attachment for Enhanced Safety in Robot-Assisted Feeding

Robot-assisted feeding systems enhance the independence of individuals with motor impairments and alleviate caregiver burden. While existing systems predominantly rely on software-based safety features to mitigate risks during unforeseen collisions, this study explores the use of a mechanical fail-safe to improve safety. We designed a breakaway utensil attachment that decouples forces exerted by the robot on the user when excessive forces occur. Finite element analysis (FEA) simulations were performed to predict failure points under various loading conditions, followed by experimental validation using 3D-printed attachments with variations in slot depth and wall loops. To facilitate testing, a drop test rig was developed and validated. Our results demonstrated a consistent failure point at the slot of the attachment, with a slot depth of 1 mm and three wall loops achieving failure at the target force of 65 N. Additionally, the parameters can be tailored to customize the breakaway force based on user-specific factors, such as comfort and pain tolerance. CAD files and utensil assembly instructions can be found here: https://tinyurl.com/rfa-utensil-attachment

cs.RO↗

arXiv2024

Personalised 3D Human Digital Twin with Soft-Body Feet for Walking Simulation

With the increasing use of assistive robots in rehabilitation and assisted mobility of human patients, there has been a need for a deeper understanding of human-robot interactions particularly through simulations, allowing an understanding of these interactions in a digital environment. There is an emphasis on accurately modelling personalised 3D human digital twins in these simulations, to glean more insights on human-robot interactions. In this paper, we propose to integrate personalised soft-body feet, generated using the motion capture data of real human subjects, into a skeletal model and train it with a walking control policy. Through evaluation using ground reaction force and joint angle results, the soft-body feet were able to generate ground reaction force results comparable to real measured data and closely follow joint angle results of the bare skeletal model and the reference motion. This presents an interesting avenue to produce a dynamically accurate human model in simulation driven by their own control policy while only seeing kinematic information during training.

cs.RO↗

arXiv2024

Design and Evaluation of a Compact 3D End-effector Assistive Robot for Adaptive Arm Support

We developed a 3D end-effector type of upper limb assistive robot, named as Assistive Robotic Arm Extender (ARAE), that provides transparency movement and adaptive arm support control to achieve home-based therapy and training in the real environment. The proposed system composes five degrees of freedom, including three active motors and two passive joints at the end-effector module. The core structure of the system is based on a parallel mechanism. The kinematic and dynamic modeling are illustrated in detail. The proposed adaptive arm support control framework calculates the compensated force based on the estimated human arm posture in 3D space. It firstly estimates human arm joint angles using two proposed methods: fixed torso and sagittal plane models without using external sensors such as IMUs, magnetic sensors, or depth cameras. The experiments were carried out to evaluate the performance of the two proposed angle estimation methods. Then, the estimated human joint angles were input into the human upper limb dynamics model to derive the required support force generated by the robot. The muscular activities were measured to evaluate the effects of the proposed framework. The obvious reduction of muscular activities was exhibited when participants were tested with the ARAE under an adaptive arm gravity compensation control framework. The overall results suggest that the ARAE system, when combined with the proposed control framework, has the potential to offer adaptive arm support. This integration could enable effective training with Activities of Daily Living (ADLs) and interaction with real environments.

cs.RO↗

arXiv2024

ExTraCT -- Explainable Trajectory Corrections from language inputs using Textual description of features

Natural language provides an intuitive and expressive way of conveying human intent to robots. Prior works employed end-to-end methods for learning trajectory deformations from language corrections. However, such methods do not generalize to new initial trajectories or object configurations. This work presents ExTraCT, a modular framework for trajectory corrections using natural language that combines Large Language Models (LLMs) for natural language understanding and trajectory deformation functions. Given a scene, ExTraCT generates the trajectory modification features (scene-specific and scene-independent) and their corresponding natural language textual descriptions for the objects in the scene online based on a template. We use LLMs for semantic matching of user utterances to the textual descriptions of features. Based on the feature matched, a trajectory modification function is applied to the initial trajectory, allowing generalization to unseen trajectories and object configurations. Through user studies conducted both in simulation and with a physical robot arm, we demonstrate that trajectories deformed using our method were more accurate and were preferred in about 80\% of cases, outperforming the baseline. We also showcase the versatility of our system in a manipulation task and an assistive feeding task.

cs.RO↗

arXiv2023

Graceful User Following for Mobile Balance Assistive Robot in Daily Activities Assistance

Numerous diseases and aging can cause degeneration of people's balance ability resulting in limited mobility and even high risks of fall. Robotic technologies can provide more intensive rehabilitation exercises or be used as assistive devices to compensate for balance ability. However, With the new healthcare paradigm shifting from hospital care to home care, there is a gap in robotic systems that can provide care at home. This paper introduces Mobile Robotic Balance Assistant (MRBA), a compact and cost-effective balance assistive robot that can provide both rehabilitation training and activities of daily living (ADLs) assistance at home. A three degrees of freedom (3-DoF) robotic arm was designed to mimic the therapist arm function to provide balance assistance to the user. To minimize the interference to users' natural pelvis movements and gait patterns, the robot must have a Human-Robot Interface(HRI) that can detect user intention accurately and follow the user's movement smoothly and timely. Thus, a graceful user following control rule was proposed. The overall control architecture consists of two parts: an observer for human inputs estimation and an LQR-based controller with disturbance rejection. The proposed controller is validated in high-fidelity simulation with actual human trajectories, and the results successfully show the effectiveness of the method in different walking modes.

cs.RO↗

arXiv2022

Safety-based Speed Control of a Wheelchair using Robust Adaptive Model Predictive Control

Electric-powered wheelchair plays an important role in providing accessibility for people with mobility impairment. Ensuring the safety of wheelchair operation in different application scenarios and for diverse users is crucial when the designing controller for tracking tasks. In this work, we propose a safety-based speed tracking control algorithm for wheelchair systems with external disturbances and uncertain parameters at the dynamic level. The set-membership approach is applied to estimate the sets of uncertain parameters online and a designed model predictive control scheme with online model and control parameter adaptation is presented to guarantee safety-related constraints during the tracking process. The proposed controller can drive the wheelchair speed to a desired reference within safety constraints. For the inadmissible reference that violates the constraints, the proposed controller can steer the system to the neighbourhood of the closest admissible reference. The effectiveness of the proposed control scheme is validated based on the high-fidelity speed tracking results of two tasks that involve feasible and infeasible references.

eess.SY↗

arXiv2018

Motor Control Insights on Walking Planner and its Stability

The application of biomechanic and motor control models in the control of bidedal robots (humanoids, and exoskeletons) has revealed limitations of our understanding of human locomotion. A recently proposed model uses the potential energy for bipedal structures to model the bipedal dynamics, and it allows to predict the system dynamics from its kinematics. This work proposes a task-space planner for human-like straight locomotion that target application of in rehabilitation robotics and computational neuroscience. The proposed architecture is based on the potential energy model and employs locomotor strategies from human data as a reference for human behaviour. The model generates Centre of Mass (CoM) trajectories, foot swing trajectories and the Base of Support (BoS) over time. The data show that the proposed architecture can generate behaviour in line with human walking strategies for both the CoM and the foot swing. Despite the CoM vertical trajectory being not as smooth as a human trajectory, yet the proposed model significantly reduces the error in the estimation of the CoM vertical trajectory compared to the inverted pendulum models. The proposed model is also able to asses the stability based on the body kinematics embedding in currently used in the clinical practice. However, the model also implies a shift in the interpretation of the spatiotemporal parameters of the gait, which are now determined by the conditions for the equilibrium and not \textit{vice versa}. In other words, locomotion is a dynamic reaching where the motor primitives are also determined by gravity.

cs.RO↗

arXiv2018

Deployment of the Saddle Space Transformation in Tracking the Base of Support

Balance is the fundamental skill behind human locomotion, and its impairment is the principal indicator of self-perceived disability. Despite significant improvements in balance assessment, there is still large incidence of fall related injuries among elderlies. The Base of Support (BoS) is a popular method for bipedal stability assessment, but its accuracy depends on the accuracy the BoS geometry measurement. This work presents a method to ease the BoS tracking by the identification of a reference frame that allows to define postural models of the BoS geometry. Although we also propose a geometry based on the geometry determined from centre of pressure range of motion within the foot obtained from literature, this methodology can be used with other models (i.e., the feasible base of support). The model has been tested with 12 healthy subjects, which have been asked to explore their stability in six different postures. The results show that the model can accurate deform the geometry of the BoS to adapt its shape to the different postures, which can remove the necessity of force/torque sensors in some application. Potentially the proposed method can be also applied to describe any posture dependent attribute (e.g., gravitational forces), and it can be also applied to bipedal robots. Therefore, it constitutes a novel mathematical tool that can be deployed to develop both better sensors and models for bipeds. For example, it can be used with the Extrapolated CoM model to evaluate dynamic stability from the body kinematics.

cs.RO↗

arXiv2018

The Strange Attractor Model of Bipedal Locomotion and its Consequences on Motor Control

Despite decades of study, many unknowns exist about the mechanisms governing human locomotion. Current models and motor control theories can only partially capture the phenomenon. This may be a major cause of the reduced efficacy of lower limb rehabilitation therapies. Recently, it has been proposed that human locomotion can be planned in the task-space by taking advantage of the gravitational pull acting on the Centre of Mass (CoM) by modelling the attractor dynamics. The model proposed represents the CoM transversal trajectory as a harmonic oscillator propagating on the attractor manifold. However, the vertical trajectory of the CoM, controlled through ankle strategies, has not been accurately captured yet. Research Questions: Is it possible to improve the model accuracy by introducing a mathematical model of the ankle strategies by coordinating the heel-strike and toe-off strategies with the CoM movement? Our solution consists of closed-form equations that plan human-like trajectories for the CoM, the foot swing, and the ankle strategies. We have tested our model by extracting the biomechanics data and postural during locomotion from the motion capture trajectories of 12 healthy subjects at 3 self-selected speeds to generate a virtual subject using our model. Our virtual subject has been based on the average of the collected data. The model output shows our virtual subject has walking trajectories that have their features consistent with our motion capture data. Additionally, it emerged from the data analysis that our model regulates the stance phase of the foot as humans do. The model proves that locomotion can be modelled as an attractor dynamics, proving the existence of a nonlinear map that our nervous system learns. It can support a deeper investigation of locomotion motor control, potentially improving locomotion rehabilitation and assistive technologies.

cs.RO↗