arXiv subjects

U. Sheikh

Publications and source records attributed to U. Sheikh.

12 recordsLinked to original sources

arXiv2026

Synthetic Diagnostic Modeling for Plasma Tomography: Geometry Matrix Computation Methods and Impact of Model Accuracy

Tomographic emissivity reconstruction from plasma diagnostics data relies on a synthetic model mapping the plasma emissivity to the measured signals. The model, referred to as a geometry matrix in the plasma imaging community, is often built using the line-of-sight (LoS) approximation. This approximation neglects the finite width of the detector viewing beams and can therefore introduce systematic errors. Physically correct volume-of-sight (VoS) models remove this inaccuracy by accounting for the full 3D extent of the viewing beams. Their adoption, however, is sometimes hindered by the difficulty of independently validating them. We present an intuitive and easily inspectable voxel-to-detector (V2D) approach for computing physically accurate VoS geometry matrices, based on discretizing the tokamak vessel into voxels and estimating the contribution of each voxel to the measurements of each detector. We apply the V2D approach to the soft X-ray (SXR) and bolometry systems of the TCV tokamak. Through phantom-based studies on physically realistic emissivity profiles, we quantify the improvement in reconstruction quality obtained by using VoS rather than LoS models. We find that the VoS model yields overall better accuracy and precision; however, interestingly, the simpler LoS model does not introduce a significant systematic bias in the estimated total, core, divertor and main chamber radiated powers. We further compare the V2D geometry matrix with an independent ray-tracing implementation, finding excellent agreement that validates both approaches for routine use at TCV. All routines developed in this work are made openly available.

physics.plasm-ph↗

arXiv2026

Evolution of SPI-induced disruptions in ASDEX Upgrade

Disruptions are a major concern for future fusion reactors based on the tokamak principle. To ensure machine protection, the thermal loads and vessel forces that arise during disruptions have to be mitigated reliably. For the ITER disruption mitigation system (DMS), the shattered pellet injection (SPI) technology has been selected. It can provide a prompt delivery of the injection material into the plasma core, with the mitigation efficiency depending on fragment size and velocity. A highly flexible SPI system was built and installed at the tokamak ASDEX Upgrade (AUG) to aid the finalization process of the ITER DMS and provide crucial input for modeling. The SPI-induced disruptions in the 2022 AUG experiments follow a typical chain of events, which are discussed in this paper: The first light, main fragment arrival, plasma movement event, MARFE, thermal quench/plasma current spike, current quench, and vertical displacement event phase. Depending on the injection parameters, these phases may vary significantly or some might not be present at all. In this paper, we will focus on the characterization of these disruption phases and figures of merit for the mitigation efficiency, depending on the SPI configuration. With increasing amount of assimilated neon in the plasma - primarily influenced by the neon content in the pellet but also the shattering parameters - the disruptions exhibit different behaviors. This disruption evolution seems to be a continuous process, with the most prominent feature being the changing disruption time scales and plasma current time trace shape during the CQ from convex (poorly or unmitigated) $\rightarrow$ concave (well mitigated/radiation dominated). Depending on the injection, pre-TQ durations between 15 - 0.5 ms and early CQ durations ($\Delta \textrm{t}_\textrm{CQ}^{100 \rightarrow 80}$) between 13.3 - 8.2 ms had been achieved at AUG.

physics.plasm-ph↗

arXiv2026

Real-time Tomography-based Bayesian Inference from TCV Bolometry Data

Radiated power information is crucial to diagnose and optimize the performance of fusion plasmas. Traditionally, at the TCV tokamak, radiated power analysis has only ever been possible following plasma discharge termination. However, recently, TCV bolometer data have become available in real-time. This offers the opportunity of integrating the radiated power information into the TCV plasma control system. In this work, we propose a novel real-time tomography-based Bayesian technique allowing estimation of the power radiated from user-defined regions of interest in the plasma. The real-time estimates are obtained as computationally cheap linear combinations of bolometer measurements, using pre-computed coefficients that are optimized for the specific discharge planned. This method is not, thus, trained on a set of synthetic or tomographically reconstructed emissivity profiles. We detail the derivation of the technique and show its equivalence to traditional tomographic estimates under suitable conditions. We then demonstrate that this technique enables accurate real-time estimation of the total, core, divertor and main chamber radiated power, by its application to a representative and heterogeneous set of TCV discharges. Finally, we discuss the robustness of the technique to faulty detectors, showing that simple precautions allow safe handling of many common issues. The computational routines implementing the described technique are provided as open-source code.

physics.plasm-ph↗

arXiv2026

Infrared Thermography in the Tokamak \`a Configuration Variable

In the Tokamak \`a Configuration Variable (TCV), infrared thermography (IR) is currently composed of the horizontal, vertical, and tangential infrared systems (HIR, VIR, TIR), which all use Equus 81k M cameras. The IR diagnostics obtain the surface temperature of TCV's graphite tiles for post-discharge analysis. Target heat flux profiles are inferred from the tile temperature with the THEODOR (Thermal Energy Onto Divertor) code. Fast transient analysis is possible in reduced frame mode, with acquisition frequencies above 10kHz. The main views are the lower inner wall for HIR, the floor for VIR, and the lower outer wall for TIR. The HIR camera can also be moved to view the midplane inner wall, while TIR can be moved to see the midplane inner wall and the upper outer wall, mainly to measure synchrotron radiation and heat deposition due to runaway electrons. Recent developments in TCV's IR systems include (i) tile diffusivity and conductivity measurements to assure the precision of heat flux estimates; (ii) the addition of one new VIR heated valley tile and two rooftop TIR tiles, for measurements of fast heat flux transients; (iii) the implementation of long-pass wavelength filter of 4095 nm, to diminish the measurement of plasma parasitic infrared light, mainly from deuterium 5-4 emission at 4051 nm. Despite these developments, the main sources of uncertainty for IR in TCV are still parasitic infrared light and the determination of the surface layer heat transmission factor, both of which mainly affect the VIR system.

physics.plasm-ph↗

arXiv2026

Non-dimensional confinement scaling in similar negative triangularity plasmas on the DIII-D and TCV tokamaks

Similarity experiments were performed on the DIII-D and TCV tokamaks to explore the scaling of energy confinement in negative triangularity plasmas using non-dimensional variables. Near up-down symmetric plasmas with large top-bottom averaged negative triangularity were created in a lower single null configuration, with the shape of the separatrix being closely matched between the two devices. The normalized energy confinement is found to weakly improve at increasing collisionality and, between the two devices, shows a machine size scaling behavior between Bohm and gyro-Bohm. Engineering scaling on a large DIII-D dataset is in agreement with the non-dimensional experiment.

physics.plasm-ph↗

arXiv2026

Quantitative 3D non-linear simulations of shattered pellet injection in ASDEX Upgrade using JOREK

Shattered pellet injection (SPI) as primary mitigation method for major disruptions in ITER has a large parameter space available for optimization including the total amount of injected material, the size of the individual pellet fragments, the material composition, and the timing of multiple injections. This flexibility needs to be exploited to simultaneously minimize thermal heat loads, electromagnetic vessel forces, and formation of relativistic electrons and their impacts on plasma facing components. In this article, we apply 3D non-linear magnetohydrodynamic modelling to SPI experiments in the ASDEX Upgrade tokamak, going beyond our previous work [Tang et al Nucl. Fusion 65 116003 (2025)] by resolving some discrepancies between simulations and experiment and thus opening the path to quantitative model validation and experiment interpretation. The key element that enables the transition from merely qualitative comparisons to quantitatively reliable predictions of the thermal quench duration and the radiation fraction is the incorporation of a simplified treatment of parallel heat-flux limiting. The work increases the confidence of matching the key processes of disruption mitigation with this high fidelity modelling in view of predictive studies for ITER.

physics.plasm-ph↗

arXiv2026

Variability of MHD Instabilities in Benign Termination of High-Current Runaway Electron Beams in the JET and DIII-D Tokamaks

Benign termination, in which magnetohydrodynamic (MHD) instabilities deconfine runaway electrons (REs) following hydrogenic injections, is a promising strategy for mitigating dangerous RE loads after disruptions. Recent experiments on the Joint European Torus (JET) have explored this scenario at higher pre-disruptive plasma currents than are achievable on other devices, revealing challenges in obtaining benign terminations at $I_p \geq 2.5$ MA. This work analyzes the evolution of these high-current RE beams and their terminating MHD events using fast magnetic sensor measurements and EFIT equilibrium reconstructions for approximately $40$ JET and $20$ DIII-D tokamak discharges. On JET, unsuccessful non-benign terminations occur at low edge safety factor ($q_{\text{edge}} \approx 2$), and are preceded by intermittent, non-terminating MHD events at higher rational $q_{\text{edge}}$. Trends in the internal inductance $l_i$ indicate more peaked RE current profiles in the high-$I_p$ non-benign population, which may hinder successful recombination through re-ionization. In contrast, benign terminations on JET typically occur at higher $q_{\text{edge}} \geq 3$ and exhibit less peaked RE current profiles. DIII-D displays a range of terminating edge safety factors, correlated with the measured $l_i$ values. Across both tokamaks, the RE current peaking is therefore found to determine which MHD instability boundary is encountered, confirmed by linear resistive MHD modeling with the CASTOR3D code. Measured growth rates are similar for benign and non-benign cases, indicating that ideal MHD timescales at low density after hydrogenic injection do not alone explain efficient RE deconfinement. Instead, non-benign cases are characterized by their lower MHD perturbation amplitudes $\delta B$. These observations suggest that the interplay between ideal and resistive dynamics governs the termination process.

physics.plasm-ph↗

arXiv2025

Runaway electron-induced plasma facing component damage in tokamaks

This Roadmap article addresses the critical and multifaceted challenge of plasma-facing component (PFC) damage caused by runaway electrons (REs) in tokamaks, a phenomenon that poses a significant threat to the viability and longevity of future fusion reactors such as ITER and DEMO. The dramatically increased RE production expected in future high-current tokamaks makes it difficult to avoid or mitigate REs when a plasma discharge terminates abnormally. Preventing damage from the intense localised heat loads REs can cause requires a holistic approach that considers plasma, REs and PFC damage. Despite decades of progress in understanding the physics of REs and the thermomechanical response of PFCs, their complex interplay remains poorly understood. This document aims to initiate a coordinated, interdisciplinary approach to bridge this gap by reviewing experimental evidence, advancing diagnostic capabilities, and improving modelling tools across different scales, dimensionalities and fidelities. Key topics include RE beam formation and transport, damage mechanisms in brittle and metallic PFCs, and observations in major facilities such as JET, DIII-D, WEST and EAST. The Roadmap emphasises the urgency of predictive, high-fidelity modelling validated against well-diagnosed controlled experiments, particularly in the light of recent changes in ITER's wall material strategy and the growing importance of private sector initiatives. Each section of the article is written to provide a concise overview of one area of this multidisciplinary subject, with an assessment of the status, a look at current and future challenges, and a brief summary. The ultimate goal of this initiative is to guide future mitigation strategies and design resilient components that can withstand the loads imposed by REs, thus ensuring the safe and sustainable operation of the next generation of fusion power plants.

physics.plasm-ph↗

arXiv2024

Expulsion of runaway electrons using ECRH in the TCV tokamak

Runaway electrons (REs) are a concern for tokamak fusion reactors from discharge startup to termination. A sudden localized loss of a multi-megaampere RE beam can inflict severe damage to the first wall. Should a disruption occur, the existence of a RE seed may play a significant role in the formation of a RE beam and the magnitude of its current. The application of central electron cyclotron resonance heating (ECRH) in the Tokamak \`a Configuration Variable (TCV) reduces an existing RE seed population by up to three orders of magnitude within only a few hundred milliseconds. Applying ECRH before a disruption can also prevent the formation of a post-disruption RE beam in TCV where it would otherwise be expected. The RE expulsion rate and consequent RE current reduction are found to increase with applied ECRH power. Whereas central ECRH is effective in expelling REs, off-axis ECRH has a comparatively limited effect. A simple 0-D model for the evolution of the RE population is presented that explains the effective ECRH-induced RE expulsion results from the combined effects of increased electron temperature and enhanced RE transport.

physics.plasm-ph↗

arXiv2022

Improved Heat and Particle Flux Mitigation in High Core Confinement, Baffled, Alternate Divertor Configurations in the TCV tokamak

Nitrogen seeded detachment has been achieved in the Tokamak a Configuration Variable (TCV) in advanced divertor configurations (ADCs), namely X-divertor and X-point target, with and without baffles in H-mode plasmas with high core confinement. Both ADCs show a remarkable reduction in the inter-ELM particle and heat fluxes to the target compared to the standard divertor configuration. 95-98% of the peak heat flux to the target is mitigated as a synergetic effect of ADCs, baffling, and nitrogen seeded detachment. The effect of divertor geometry and baffles on core-divertor compatibility is investigated in detail. The power balance in these experiments is also investigated to explore the physics behind the observed reduction in heat fluxes in the ADCs.

physics.plasm-ph↗

arXiv2017

Impurity seeding for suppression of the near Scrape-Off Layer heat flux feature in tokamak limited plasmas

In inboard-limited plasmas, foreseen to be used in future fusion reactors start-up and ramp down phases, the Scrape-Off Layer (SOL) exhibits two regions: the "near" and "far" SOL. The steep radial gradient of the parallel heat flux associated with the near SOL can result in excessive thermal loads onto the solid surfaces, damaging them and/or limiting the operational space of a fusion reactor. In this article, leveraging the results presented in [F. Nespoli et al., Nuclear Fusion 2017], we propose a technique for the mitigation and suppression of the near SOL heat flux feature by impurity seeding. First successful experimental results from the TCV tokamak are presented and discussed.

physics.plasm-ph↗

arXiv2016

Spectroscopic investigations of divertor detachment in TCV

The aim of this work is to provide an understanding of detachment at TCV with emphasis on analysis of the Balmer line emission. A new Divertor Spectroscopy System has been developed for this purpose. Further development of Balmer line analysis techniques has allowed detailed information to be extracted from the three-body recombination contribution to the n=7 Balmer line intensity. During density ramps, the plasma at the target detaches as inferred from a drop in ion current to the target. At the same time the Balmer $6\rightarrow2$ and $7\rightarrow2$ line emission near the target is dominated by recombination. As the core density increases further, the density and recombination rate are rising all along the outer leg to the x-point while remaining highest at the target. Even at the highest core densities accessed (Greenwald fraction 0.7) the peaks in recombination and density may have moved not more than a few cm poloidally away from the target which is different to other, higher density tokamaks, where both the peak in recombination and density continue to move towards the x-point as the core density is increased. The inferred magnitude of recombination is small compared to the target ion current at the time detachment (particle flux drop) starts at the target. However, recombination may be having more localized effects (to a flux tube) which we cannot discern at this time. Later, at the highest densities achieved, the total recombination does reach levels similar to the particle flux.

physics.plasm-ph↗