arXiv subjects

U. Kumar

Publications and source records attributed to U. Kumar.

10 recordsLinked to original sources

arXiv2026

Design of a Doppler backscattering diagnostic for the Wisconsin HTS Axisymmetric Mirror (WHAM)

The Wisconsin HTS Axisymmetric Mirror (WHAM) is a compact high-field magnetic mirror. In such magnetic mirrors, cross-field transport is dominated by the flute instability (Endrizzi et al., 2023). To investigate density fluctuations associated with the flute instability, we designed a Doppler backscattering (DBS) diagnostic for WHAM, to be installed at the midplane port window. The diagnostic uses a two-channel tunable Ka-band (26.5--40 GHz) source and X-mode polarization. The azimuthal launch angle is set mechanically by rotating the external quasioptical assembly. As such, the system is reconfigurable during dedicated setup periods. Using the \textit{Scotty} beam-tracing code (Hall-Chen et al., 2022), we show that the proposed DBS system can measure density fluctuations with perpendicular wavenumbers $1 \leq k_\perp \leq 3~\mathrm{cm}^{-1}$ over radial locations $0.7 \leq \rho \leq 0.9$, where $\rho$ is the normalized radial coordinate. This is achieved with probe frequencies between 28 and 38.5 GHz, an elevation launch angle of $0^\circ$, and azimuthal launch angles in the range $1^\circ$--$3^\circ$. The selected configurations have low mismatch angle at cutoff, $|\theta_{m,c}|<1^\circ$. The quasioptical system uses a Ka-band horn and a biconvex ultra-high molecular weight polyethylene lens, and satisfies the port-access constraints in WHAM. The planned microwave system has a monostatic, homodyne architecture based on two phase-coupled Ka-band microwave channels. These two channels will be for the transmitted signal and coherent local oscillator (LO) for IQ downconversion, respectively. As the two phase-coupled channels can be independently tuned or swept with a controlled frequency offset, the same microwave chain can also support profile-reflectometry measurements using cutoff-delay information.

physics.plasm-ph↗

arXiv2026

Disentangling multi-spin dynamic correlations in the Heisenberg spin-$\frac{1}{2}$ chain

Higher-order correlations are essential for understanding exotic phases and uncovering universal aspects of quantum dynamics. While inelastic neutron scattering provides well-established access to two-particle correlations, measuring correlations in solids involving more than two particles remains a major challenge. Focusing on magnetic excitations in the Heisenberg spin-$\frac{1}{2}$ chain, we demonstrate that resonant inelastic X-ray scattering (RIXS) can selectively probe multi-spin dynamical correlations by exciting distinct intermediate states through energy detuning. Through theoretical modeling, we isolate the two- and multi- spin responses, and establish that: (i) The resonant energies of the two- and multi- spin dynamical correlations are separated by $\approx \frac{3}{4}J$; implying that the multi-spin part of the cross-section comes from intermediate states that contain spin flips; (ii) The spectral weight of the two-spin channel exhibits a Lorentzian resonant energy profile consistent with a single dominant electronic configuration, whereas the multi-spin channel response shows a Gaussian-like profile, implying contributions from multiple intermediate spin configurations. These characteristics are reproduced by exact diagonalization of the $t-J$ Hamiltonian, which further reveals that the widths of Lorentzian and Gaussian resonant energy profiles depend primarily on core-hole lifetime ($\Gamma/2$) and $\frac{2J}{\Gamma}$, respectively. Controlled access to multi-spin dynamics, using RIXS energy detuning as a knob, can open new pathways to explore many-body dynamics in quantum materials.

cond-mat.str-el↗

arXiv2026

Design of a multifunctional Doppler backscattering diagnostic for the Pegasus-III Experiment

The Doppler backscattering (DBS) diagnostic measures flows and electron density fluctuations. Recent work indicates that DBS can also infer the magnetic pitch angle (Yeoh et al., NF 2026). We present the preliminary design of a DBS for the Pegasus-III Experiment. This DBS will serve two objectives. First, it will advance diagnostic science, by supporting understanding of the DBS instrumentation functions, using DBS to constrain the magnetic equilibrium, and data-driven inference of plasma properties from DBS signals. Secondly, it will support Pegasus-IIIs research directions, such as solenoid-free plasma initiation and O-X-B mode conversion for heating and current drive, since density fluctuations affect mode conversion efficiency and pitch angle measurements can be used to locate the mode conversion window. This ex-vacuum DBS system uses a single channel, tuneable Ka-band source, a corrugated horn antenna, and a homodyne I/Q receiver with baseband digitization. For greater flexibility, which is especially important for pitch angle measurements, the quasioptical elements include a rotatable spinner for O- and X-mode selection and a mirror with 2D steering. Using the \textit{Scotty} beam-tracing code, for a range of poloidal launch angles $8^\circ$ to $18^\circ$ and a corresponding toroidal launch angle between $0^\circ$ to $3^\circ$ for maximal backscattered DBS power, we find that the DBS system is capable of measuring ion-scale density fluctuations $1\leq k_{\perp,c} \leq8 \text{ cm}^{-1}$ at a range of normalized radial coordinates from the outer core ($\rho \sim 0.65$) to just beyond the last-closed flux surface (LCFS), where $\rho=0$ corresponds to the magnetic axis and $\rho=1$ the LCFS. The system is also designed with additional toroidal steering capability, $-4^\circ$ to $8^\circ$, to resolve the toroidal response needed for magnetic pitch angle measurements.

physics.plasm-ph↗

arXiv2024

Expulsion of runaway electrons using ECRH in the TCV tokamak

Runaway electrons (REs) are a concern for tokamak fusion reactors from discharge startup to termination. A sudden localized loss of a multi-megaampere RE beam can inflict severe damage to the first wall. Should a disruption occur, the existence of a RE seed may play a significant role in the formation of a RE beam and the magnitude of its current. The application of central electron cyclotron resonance heating (ECRH) in the Tokamak \`a Configuration Variable (TCV) reduces an existing RE seed population by up to three orders of magnitude within only a few hundred milliseconds. Applying ECRH before a disruption can also prevent the formation of a post-disruption RE beam in TCV where it would otherwise be expected. The RE expulsion rate and consequent RE current reduction are found to increase with applied ECRH power. Whereas central ECRH is effective in expelling REs, off-axis ECRH has a comparatively limited effect. A simple 0-D model for the evolution of the RE population is presented that explains the effective ECRH-induced RE expulsion results from the combined effects of increased electron temperature and enhanced RE transport.

physics.plasm-ph↗

arXiv2022

Crossover of the high-energy spin fluctuations from collective triplons to localized magnetic excitations in doped Sr14-xCaxCu24O41 cuprate ladders

We studied the magnetic excitations in the quasi-one-dimensional (q-1D) ladder subsystem of Sr_(14-x) Ca_x Cu_24 O_41(SCCO) using Cu L_3-edge resonant inelastic X-ray scattering (RIXS). By comparing momentum-resolved RIXS spectra with (x=12.2) and without (x=0) high Ca content, we track the evolution of the magnetic excitations from collective two-triplon (2T) excitations (x=0) to weakly-dispersive gapped modes at an energy of 280 meV (x=12.2). Density matrix renormalization group (DMRG) calculations of the RIXS response in the doped ladders suggest that the flat magnetic dispersion and damped excitation profile observed at x=12.2 originates from enhanced hole localization. This interpretation is supported by polarization-dependent RIXS measurements, where we disentangle the spin-conserving {\Delta}S=0 scattering from the predominant {\Delta}S=1 spin-flip signal in the RIXS spectra. The results show that the low-energy weight in the {\Delta}S=0 channel is depleted when Sr is replaced by Ca, consistent with a reduced carrier mobility. Our results demonstrate that off-ladder impurities can affect both the low-energy magnetic excitations and superconducting correlations in the CuO_4 plaquettes. Finally, our study characterizes the magnetic and charge fluctuations in the phase from which superconductivity emerges in SCCO at elevated pressures.

cond-mat.supr-con↗

arXiv2020

Apparent Differences between Single Layer Molybdenum Disulfide Fabricated via Chemical Vapor Deposition and Exfoliation

Innovative applications based on two-dimensional solids require cost-effective fabrication processes resulting in large areas of high quality materials. Chemical vapour deposition is among the most promising methods to fulfill these requirements. However, for 2D materials prepared in this way it is generally assumed that they are of inferior quality in comparison to the exfoliated 2D materials commonly used in basic research. In this work we challenge this assumption and aim to quantify the differences in quality for the prototypical transition metal dichalcogenide MoS$_2$. To this end single layers of MoS$_2$ prepared by different techniques (exfoliation, grown by different chemical vapor deposition methods, transfer techniques, and as vertical heterostructure with graphene) are studied by Raman and photoluminescence spectroscopy, complemented by atomic force microscopy. We demonstrate that as-prepared MoS$_2$, directly grown on SiO$_2$, differs from exfoliated MoS$_2$ in terms of higher photoluminescence, lower electron concentration, and increased strain. As soon as a water film is intercalated (e.g., by transfer) underneath the grown MoS$_2$, in particular the (opto-)electronic properties become practically identical to those of exfoliated MoS$_2$. A comparison of the two most common precursors shows that the growth with MoO$_3$ causes greater strain and/or defect density deviations than growth with ammonium heptamolybdate. As part of a heterostructure directly grown MoS$_2$ interacts much stronger with the substrate, and in this case an intercalated water film does not lead to the complete decoupling, which is typical for exfoliation or transfer. Our work shows that the supposedly poorer quality of grown 2D transition metal dichalcogenides is indeed a misconception.

cond-mat.mtrl-sci↗

arXiv2020

Instability and evolution of the magnetic ground state in metallic perovskites GdRh$_3$C$_{1-x}$B$_x$

We report investigations of the structural, magnetic, electrical transport and thermal properties of five compositions of the metallic perovskite GdRh$_3$C$_{1-x}$B$_x$ ($0.00 \le x \le 1.00$). Our results show that all the five compositions undergo magnetic ordering at low temperatures, but the nature of the ordered state is significantly different in the carbon- and the boron-rich compositions, where the former shows signatures of an amplitude-modulated magnetic structure and the latter exhibits evidences of an equal-moment incommensurate antiferromagnetic ordering. We also observe a remarkable field-dependent evolution of conduction carrier polarization in the compositionally disordered compounds. The outcomes indicate that this system is energetically situated in proximity to a magnetic instability where small variations in the control parameter(s), such as lattice constant and/or electron density, lead to considerably different ground states.

cond-mat.str-el↗

arXiv2018

Computing Resonant Inelastic X-Ray Scattering Spectra Using The Density Matrix Renormalization Group Method

We present a method for computing resonant inelastic x-ray scattering (RIXS) spectra in one-dimensional systems using the density matrix renormalization group (DMRG) method. By using DMRG to address the problem, we shift the computational bottleneck from the memory requirements associated with exact diagonalization (ED) calculations to the computational time associated with the DMRG algorithm. This approach is then used to obtain RIXS spectra on cluster sizes well beyond state-of-the-art ED techniques. Using this new procedure, we compute the low-energy magnetic excitations observed in Cu $L$-edge RIXS for the challenging corner shared CuO$_4$ chains, both for large multi-orbital clusters and downfolded $t$-$J$ chains. We are able to directly compare results obtained from both models defined in clusters with identical momentum resolution. In the strong coupling limit, we find that the downfolded $t$-$J$ model captures the features of the magnetic excitations probed by RIXS after a uniform scaling of the spectra is taken into account.

cond-mat.str-el↗

arXiv2018

Direct observation of multi-spinon excitations outside of the two-spinon continuum in the antiferromagnetic spin chain cuprate Sr2CuO3

One-dimensional (1D) magnetic insulators have attracted significant interest as a platform for studying emergent phenomena such as quasiparticle fractionalization and quantum criticality. The antiferromagnetic Heisenberg chain of spins-1/2 is an important reference system; its elementary excitations are spin-1/2 quasiparticles called spinons that are always created in pairs. However, while inelastic neutron scattering (INS) experiments routinely observe the excitation continuum associated with two-spinon states, the presence of more complex dynamics associated with four-spinon states has only been inferred from comparison with theory. Here, we show that resonant inelastic x-ray scattering (RIXS) is capable of accessing the four-spinon excitations directly, in a spectroscopic region separated from the two-spinon continuum. Our results provide the first direct measurement of four-spinon excitations, which is made possible by the fundamentally different correlation functions probed by RIXS compared to INS. This advance holds great promise as a tool in the search for novel quantum states, in particular quantum spin liquids.

cond-mat.str-el↗

arXiv2013

A study of crossover from 3D ferrimagnetic Bulk $NiCr_{2}O_{4}$ compound into 2D spin-glass like nanophase

In this report, the magnetic behaviour of $NiCr_{2}O_{4}$ bulk and nanoparticle samples under different applied magnetic field has been investigated extensively. Nanoparticles of $NiCr_{2}O_{4}$ were obtained by mechanical milling of polycrystalline powder prepared by polyol method. FC-ZFC measurement of bulk at different applied magnetic field has revealed the existence of a ferrimagnetic transition around 66K followed by an antiferromagnetic transition close to 30K. However, its nano counterpart has shown remarkable change in magnetic properties - a suppression of ferrimagnetic transition accompanied by strengthening low temperature magnetic phase and observation of a new transition at 90K ($T_P$), which is weakly magnetic in nature. The frequency dependent ac susceptibility data of nanoparticle have been fitted to the well known de Almedia-Thouless equation and a $H^{2/3}$ dependence of the low temperature peak is observed with a resulting zero field freezing temperature ($T_f^0$) equal to 10.1K. Further, the dynamical behaviour near freezing temperature has been analysed in terms of critical behaviour and the obtained fitted parameters values being as $\tau_0$(relaxation time constant) = $3.6 X 10^{-6}s$, $T_f^0=8.7$K and $z\nu = 11.1$. Moreover, Vogel-Fulcher law has been used to understand the nature of freezing transition and the parameter after fitting are obtained as $E_a/k_B = 58.9$K, $\tau_0 = 5.22 \times 10^{-8}$ and $T_0 = 8.03$K. Finally, the spin-glass phase is concluded. Moreover, in contrast to bulk, the $H^{2/3}$ dependence of freezing temperature of nanoparticle sample (75h) does support the 2D surface like spin glass nature.

cond-mat.str-el↗