arXiv Science⌕ Search

arXiv subjects

Stephan ten Brink

Publications and source records attributed to Stephan ten Brink.

At least 91 records · Page 5Linked to original sources

Wiener Filter versus Recurrent Neural Network-based 2D-Channel Estimation for V2X Communications

We compare the potential of neural network (NN)-based channel estimation with classical linear minimum mean square error (LMMSE)-based estimators, also known as Wiener filtering. For this, we propose a low-complexity recurrent neural network (RNN)-based estimator that allows channel equalization of a sequence of channel observations based on independent time- and frequency-domain long short-term memory (LSTM) cells. Motivated by Vehicle-to-Everything (V2X) applications, we simulate time- and frequency-selective channels with orthogonal frequency division multiplex (OFDM) and extend our channel models in such a way that a continuous degradation from line-of-sight (LoS) to non-line-of-sight (NLoS) conditions can be emulated. It turns out that the NN-based system cannot just compete with the LMMSE equalizer, but it also can be trained w.r.t. resilience against system parameter mismatch. We thereby showcase the conceptual simplicity of such a data-driven system design, as this not only enables more robustness against, e.g., signal-to-noise-ratio (SNR) or Doppler spread estimation mismatches, but also allows to use the same equalizer over a wider range of input parameters without the need of re-building (or re-estimating) the filter coefficients. Particular attention has been paid to ensure compatibility with the existing IEEE 802.11p piloting scheme for V2X communications. Finally, feeding the payload data symbols as additional equalizer input unleashes further performance gains. We show significant gains over the conventional LMMSE equalization for highly dynamic channel conditions if such a data-augmented equalization scheme is used.

cs.IT↗

On the Automorphism Group of Polar Codes

The automorphism group of a code is the set of permutations of the codeword symbols that map the whole code onto itself. For polar codes, only a part of the automorphism group was known, namely the lower-triangular affine group (LTA), which is solely based upon the partial order of the code's synthetic channels. Depending on the design, however, polar codes can have a richer set of automorphisms. In this paper, we extend the LTA to a larger subgroup of the general affine group (GA), namely the block lower-triangular affine group (BLTA) and show that it is contained in the automorphism group of polar codes. Furthermore, we provide a low complexity algorithm for finding this group for a given information/frozen set and determining its size. Most importantly, we apply these findings in automorphism-based decoding of polar codes and report a comparable error-rate performance to that of successive cancellation list (SCL) decoding with significantly lower complexity.

cs.IT↗

Massive-MIMO Iterative Channel Estimation and Decoding (MICED) in the Uplink

Massive MIMO uses a large number of antennas to increase the spectral efficiency (SE) through spatial multiplexing of users, which requires accurate channel state information. It is often assumed that regular pilots (RP), where a fraction of the time-frequency resources is reserved for pilots, suffices to provide high SE. However, the SE is limited by the pilot overhead and pilot contamination. An alternative is superimposed pilots (SP) where all resources are used for pilots and data. This removes the pilot overhead and reduces pilot contamination by using longer pilots. However, SP suffers from data interference that reduces the SE gains. This paper proposes the Massive-MIMO Iterative Channel Estimation and Decoding (MICED) algorithm where partially decoded data is used as side-information to improve the channel estimation and increase SE. We show that users with precise data estimates can help users with poor data estimates to decode. Numerical results with QPSK modulation and LDPC codes show that the MICED algorithm increases the SE and reduces the block-error-rate with RP and SP compared to conventional methods. The MICED algorithm with SP delivers the highest SE and it is especially effective in scenarios with short coherence blocks like high mobility or high frequencies.

cs.IT↗

Iterative Detection and Decoding of Finite-Length Polar Codes in Gaussian Multiple Access Channels

We consider the usage of finite-length polar codes for the Gaussian multiple access channel (GMAC) with a finite number of users. Based on the interleave-division multipleaccess (IDMA) concept, we implement an iterative detection and decoding non-orthogonal multiple access (NOMA) receiver that benefits from a low complexity, while scaling (almost) linearly with the amount of active users. We further show the conceptual simplicity of the belief propagation (BP)-based decoder in a step-by-step illustration of its construction. Beyond its conceptual simplicity, this approach benefits from an improved performance when compared to some recent work tackling the same problem, namely the setup of finite-length forward errorcorrection (FEC) codes for finite-number of users. We consider the 5th generation mobile communication (5G) polar code with a block length $N = 512$ applied to both a two-user and a four-user GMAC scenario with a sum-rate of $R_{sum} = 0.5$ and $R_{sum} = 1$, respectively. Simulation results show that a BP-based soft interference cancellation (SoIC) receiver outperforms a joint successive cancellation (JSC) scheme. Finally, we investigate the effect of a concatenated repetition code which suggests that alternative polar code design rules are required in multi-user scenarios.

cs.IT↗

Massive MIMO Channel Measurements and Achievable Rates in a Residential Area

In this paper we present a measurement set-up for massive MIMO channel sounding that shows very good long-term phase stability. Initial measurements were performed in a residential area to evaluate different conventional precoding schemes such as maximum ratio transmission and phase only precoding. A massive amount of data points was collected, with 924 times 64 complex channel weights per data point. Each data point is position-tagged using differential GPS with real-time kinematik, achieving better than 35cm position accuracy in more than 90% of the collected data points, making this dataset a rich resource for, e.g., further studying machine learning based, data-driven approaches in wireless communications.

eess.SP↗

Deep-learning Autoencoder for Coherent and Nonlinear Optical Communication

Motivated by the recent success of end-to-end training of communications in the wireless domain, we strive to adapt the end-to-end-learning idea from the wireless case (i.e., linear) to coherent optical fiber links (i.e., nonlinear). Although, at first glance, it sounds like a straightforward extension, it turns out that several pitfalls exist - in terms of theory but also in terms of practical implementation. This paper analyzes the potential of an autoencoder and limitations for the optical fiber under the influence of Kerr-nonlinearity and chromatic dispersion. As there is no exact capacity limit known and, hence, no analytical perfect system solution available, we set great value to the interpretability on the learnings of the autoencoder. Therefore, we design its architecture to be as close as possible to the structure of a classic communication system, knowing that this may limit its degree of freedom and, thus, its performance. Nevertheless, we were able to achieve an unexpected high gain in terms of spectral efficiency compared to a conventional reference system.

cs.IT↗

Trainable Communication Systems: Concepts and Prototype

We consider a trainable point-to-point communication system, where both transmitter and receiver are implemented as neural networks (NNs), and demonstrate that training on the bit-wise mutual information (BMI) allows seamless integration with practical bit-metric decoding (BMD) receivers, as well as joint optimization of constellation shaping and labeling. Moreover, we present a fully differentiable neural iterative demapping and decoding (IDD) structure which achieves significant gains on additive white Gaussian noise (AWGN) channels using a standard 802.11n low-density parity-check (LDPC) code. The strength of this approach is that it can be applied to arbitrary channels without any modifications. Going one step further, we show that careful code design can lead to further performance improvements. Lastly, we show the viability of the proposed system through implementation on software-defined radios (SDRs) and training of the end-to-end system on the actual wireless channel. Experimental results reveal that the proposed method enables significant gains compared to conventional techniques.

cs.IT↗

Successive Eigenvalue Removal for Multi-Soliton Spectral Amplitude Estimation

Optical nonlinear Fourier transform-based communication systems require an accurate estimation of a signal's nonlinear spectrum, computed usually by piecewise approximation methods on the signal samples. We propose an algorithm, named successive eigenvalue removal, to improve the spectrum estimation of a multi-soliton pulse. It exploits a property of the Darboux transform that allows removing eigenvalues from the nonlinear spectrum. This results in a smaller pulse duration and smaller bandwidth. The spectral coefficients are estimated successively after removing the eigenvalues of a signal. As a beneficial application, we show that the algorithm decreases the computational complexity by iteratively reducing the pulse duration.

cs.IT↗

WGAN-based Autoencoder Training Over-the-air

The practical realization of end-to-end training of communication systems is fundamentally limited by its accessibility of the channel gradient. To overcome this major burden, the idea of generative adversarial networks (GANs) that learn to mimic the actual channel behavior has been recently proposed in the literature. Contrarily to handcrafted classical channel modeling, which can never fully capture the real world, GANs promise, in principle, the ability to learn any physical impairment, enabled by the data-driven learning algorithm. In this work, we verify the concept of GAN-based autoencoder training in actual over-the-air (OTA) measurements. To improve training stability, we first extend the concept to conditional Wasserstein GANs and embed it into a state-of-the-art autoencoder-architecture, including bitwise estimates and an outer channel code. Further, in the same framework, we compare the existing three different training approaches: model-based pre-training with receiver finetuning, reinforcement learning (RL) and GAN-based channel modeling. For this, we show advantages and limitations of GAN-based end-to-end training. In particular, for non-linear effects, it turns out that learning the whole exploration space becomes prohibitively complex. Finally, we show that the training strategy benefits from a simpler (training) data acquisition when compared to RL-based training, which requires continuous transmitter weight updates. This becomes an important practical bottleneck due to limited bandwidth and latency between transmitter and training algorithm that may even operate at physically different locations.

cs.IT↗

CRC-Aided Belief Propagation List Decoding of Polar Codes

Although iterative decoding of polar codes has recently made huge progress based on the idea of permuted factor graphs, it still suffers from a non-negligible performance degradation when compared to state-of-the-art CRC-aided successive cancellation list (CA-SCL) decoding. In this work, we show that iterative decoding of polar codes based on the belief propagation list (BPL) algorithm can approach the error-rate performance of CA-SCL decoding and, thus, can be efficiently used for decoding the standardized 5G polar codes. Rather than only utilizing the cyclic redundancy check (CRC) as a stopping condition (i.e., for error-detection), we also aim to benefit from the error-correction capabilities of the outer CRC code. For this, we develop two distinct soft-decision CRC decoding algorithms: a Bahl-Cocke-Jelinek-Raviv (BCJR)-based approach and a sum product algorithm (SPA)-based approach. Further, an optimized selection of permuted factor graphs is analyzed and shown to reduce the decoding complexity significantly. Finally, we benchmark the proposed CRC-aided belief propagation list (CA-BPL) to state-of-the-art 5G polar codes under CA-SCL decoding and, thereby, showcase an error-rate performance not just close to the CA-SCL but also close to the maximum likelihood (ML) bound as estimated by ordered statistic decoding (OSD).

cs.IT↗

On Recurrent Neural Networks for Sequence-based Processing in Communications

In this work, we analyze the capabilities and practical limitations of neural networks (NNs) for sequence-based signal processing which can be seen as an omnipresent property in almost any modern communication systems. In particular, we train multiple state-of-the-art recurrent neural network (RNN) structures to learn how to decode convolutional codes allowing a clear benchmarking with the corresponding maximum likelihood (ML) Viterbi decoder. We examine the decoding performance for various kinds of NN architectures, beginning with classical types like feedforward layers and gated recurrent unit (GRU)-layers, up to more recently introduced architectures such as temporal convolutional networks (TCNs) and differentiable neural computers (DNCs) with external memory. As a key limitation, it turns out that the training complexity increases exponentially with the length of the encoding memory $ν$ and, thus, practically limits the achievable bit error rate (BER) performance. To overcome this limitation, we introduce a new training-method by gradually increasing the number of ones within the training sequences, i.e., we constrain the amount of possible training sequences in the beginning until first convergence. By consecutively adding more and more possible sequences to the training set, we finally achieve training success in cases that did not converge before via naive training. Further, we show that our network can learn to jointly detect and decode a quadrature phase shift keying (QPSK) modulated code with sub-optimal (anti-Gray) labeling in one-shot at a performance that would require iterations between demapper and decoder in classic detection schemes.

cs.IT↗

Deep Learning-based Polar Code Design

In this work, we introduce a deep learning-based polar code construction algorithm. The core idea is to represent the information/frozen bit indices of a polar code as a binary vector which can be interpreted as trainable weights of a neural network (NN). For this, we demonstrate how this binary vector can be relaxed to a soft-valued vector, facilitating the learning process through gradient descent and enabling an efficient code construction. We further show how different polar code design constraints (e.g., code rate) can be taken into account by means of careful binary-to-soft and soft-to-binary conversions, along with rate-adjustment after each learning iteration. Besides its conceptual simplicity, this approach benefits from having the "decoder-in-the-loop", i.e., the nature of the decoder is inherently taken into consideration while learning (designing) the polar code. We show results for belief propagation (BP) decoding over both AWGN and Rayleigh fading channels with considerable performance gains over state-of-the-art construction schemes.

cs.IT↗

Optimizing Polar Codes Compatible with Off-the-Shelf LDPC Decoders

Previous work showed that polar codes can be decoded using off-the-shelf LDPC decoders by imposing special constraints on the LDPC code structure, which, however, resulted in some performance degradation. In this paper we show that this loss can be mitigated; in particular, we demonstrate how the gap between LDPC-style decoding and Arikan's Belief Propagation (BP) decoding of polar codes can be closed by taking into account the underlying graph structure of the LDPC decoder while jointly designing the polar code and the parity-check matrix of the corresponding LDPC-like code. The resulting polar codes under conventional LDPC-style decoding are shown to have similar error-rate performance when compared to some well-known and standardized LDPC codes. Moreover, we obtain performance gains in the high SNR region.

cs.IT↗

Decoder-in-the-Loop: Genetic Optimization-based LDPC Code Design

LDPC code design tools typically rely on asymptotic code behavior and are affected by an unavoidable performance degradation due to model imperfections in the short length regime. We propose an LDPC code design scheme based on an evolutionary algorithm, the Genetic Algorithm (GenAlg), implementing a "decoder-in-the-loop" concept. It inherently takes into consideration the channel, code length and the number of iterations while optimizing the error-rate of the actual decoder hardware architecture. We construct short length LDPC codes (i.e., the parity-check matrix) with error-rate performance comparable to, or even outperforming that of well-designed standardized short length LDPC codes over both AWGN and Rayleigh fading channels. Our proposed algorithm can be used to design LDPC codes with special graph structures (e.g., accumulator-based codes) to facilitate the encoding step, or to satisfy any other practical requirement. Moreover, GenAlg can be used to design LDPC codes with the aim of reducing decoding latency and complexity, leading to coding gains of up to $0.325$ dB and $0.8$ dB at BLER of $10^{-5}$ for both AWGN and Rayleigh fading channels, respectively, when compared to state-of-the-art short LDPC codes. Also, we analyze what can be learned from the resulting codes and, as such, the GenAlg particularly highlights design paradigms of short length LDPC codes (e.g., codes with degree-1 variable nodes obtain very good results).

cs.IT↗

SINR Analysis of Different Multicarrier Waveforms over Doubly Dispersive Channels

Wireless channels generally exhibit dispersion in both time and frequency domain, known as doubly selective or doubly dispersive channels. To combat the delay spread effect, multicarrier modulation (MCM) such as orthogonal frequency division multiplexing (OFDM) and its universal filtered variant (UF-OFDM) is employed, leading to the simple per-subcarrier one tap equalization. The time-varying nature of the channel, in particular, the intra-multicarrier-symbol channel variation induces spectral broadening and thus inter-carrier interference (ICI). Existing works address both effects separately, focus on the one effect while ignoring the respective other. This paper considers both effect simultaneously for cyclic prefix (CP)-, zero padded (ZP)- and UF-based OFDM with simple one tap equalization, assuming a general wireless channel model. For this general channel model, we show that the independent (wide sense stationary uncorrelated scatter, WSSUS) selectivity in time and frequency starts to intertwine in contrast to the ideal cases with single selectivity. We derive signal-to-interference-plus-noise ratio (SINR) in closed form for arbitrary system settings and channel parameters, e.g., bandwidth, delay- and Doppler-spread. With the SINR analysis, we compare the three MCM schemes under different channel scenarios.

cs.IT↗

Achievable Rate Region for Iterative Multi-User Detection via Low-cost Gaussian Approximation

We establish a multiuser extrinsic information transfer (EXIT) chart area theorem for the interleave-division multiple access (IDMA) scheme, a special form of superposition coding, in multiple access channels (MACs). A low-cost multi-user detection (MUD) based on the Gaussian approximation (GA) is assumed. The evolution of mean-square errors (MSE) of the GA-based MUD during iterative processing is studied. We show that the K-dimensional tuples formed by the MSEs of K users constitute a conservative vector field. The achievable rate is a potential function of this conservative field, so it is the integral along any path in the field with value of the integral solely determined by the two path terminals. Optimized codes can be found given the integration paths in the MSE fields by matching EXIT type functions. The above findings imply that i) low-cost GA detection can provide near capacity performance, ii) the sum-rate capacity can be achieved independently of the integration path in the MSE fields; and iii) the integration path can be an extra degree of freedom for code design.

cs.IT↗

Achievable Rate Region for Iterative Multi-User Detection via Low-cost Gaussian Approximation

We establish a multi-user extrinsic information transfer (EXIT) chart area theorem for the interleave-division multiple-access (IDMA) scheme, a special form of superposition coding, in multiple access channels (MACs). A low-cost multi-user detection (MUD) based on the Gaussian approximation (GA) is assumed. The evolution of mean-square errors (MSE) of the GA-based MUD during iterative processing is studied. We show that the K-dimensional tuples formed by the MSEs of K users constitute a conservative vector field. The achievable rate is a potential function of this conservative field, so it is the integral along any path in the field with value of the integral solely determined by the two path terminals. Optimized codes can be found given the integration paths in the MSE fields by matching EXIT type functions. The above findings imply that i) low-cost GA-based MUD can provide near capacity performance; ii) the sum-rate capacity (region) can be achieved independently of the integration path in the MSE fields; and iii) the integration path can be an extra degree of freedom for code design.

cs.IT↗

Near-Capacity Detection and Decoding: Code Design for Dynamic User Loads in Gaussian Multiple Access Channels

This paper considers the forward error correction (FEC) code design for approaching the capacity of a dynamic multiple access channel (MAC) where both the number of users and their respective signal powers keep constantly changing, resembling the scenario of an actual wireless cellular system. To obtain a low-complexity non-orthogonal multiple access (NOMA) scheme, we propose a serial concatenation of a low-density parity-check (LDPC) code and a repetition code (REP), this way achieving near Gaussian MAC (GMAC) capacity performance while coping with the dynamics of the MAC system. The joint optimization of the LDPC and REP codes is addressed by matching the analytical extrinsic information transfer (EXIT) functions of the sub-optimal multi-user detector (MUD) and the channel code for a specific and static MAC system, achieving near-GMAC capacity. We show that the near-capacity performance can be flexibly maintained with the same LDPC code regardless of the variations in the number of users and power levels. This flexibility (or elasticity) is provided by the REP code, acting as "user-load and power equalizer", dramatically simplifying the practical implementation of NOMA schemes, as only a single LDPC code is needed to cope with the dynamics of the MAC system.

cs.IT↗