arXiv subjects

Saptarshi Basu

Publications and source records attributed to Saptarshi Basu.

51 records · Page 3Linked to original sources

arXiv2021

Penetration and Secondary Atomization of Droplets Impacted on Wet Facemasks

Face covering, commonly known as facemask, is considered to be one of the most effective Personal Protective Equipments (PPEs) to reduce transmissions of pathogens through respiratory droplets - both large drops and liquid aerosol particles. Face masks, not only inhibit the expulsion of such respiratory droplets from the user, but also protects the user from inhaling pathogen-laden potentially harmful droplets or their dried nuclei. While the efficacies of various dry face masks have been explored in the recent past, a comprehensive investigation of a wet mask is lacking. Yet, users wear masks for a long period of time and during this period, owing to respiratory droplets released through multiple respiratory events, the mask matrix becomes wet. We, herein, present an experimental study on the dynamics of sequential impacts of droplets on masks to understand how wetness affects possible penetration and secondary atomization of the impacted droplet. Two different types of masks, hydrophobic and hydrophilic, were used in this study to evaluate the underlying physical mechanism that controls the penetration in each of them.

physics.flu-dyn↗

arXiv2021

Effect of wall roughness on heat transfer in the supercritical water flow

This paper discusses the numerical investigation of the wall roughness effect on the supercritical water flow susceptible to heat transfer deterioration (HTD). The simulation was carried in the vertical circular pipe using the SST k-omega turbulence model for different sets of heat flux (220kW/m2 & 1810kW/m2) and mass flow rate (0.0106kg/s &0.022kg/s) at a maximum pressure of 25.3MPa. The presence of roughness was incorporated as a uniform sand-grain roughness on the heated wall. As a result, HTD recuperated gradually as the roughness height (Ks) was increased. The mitigation of HTD is a direct consequence of the increase in turbulent kinetic energy (TKE). In contrast, the delay in the onset of HTD is due to the decrease in the dominant forces (buoyancy or acceleration effects) responsible for HTD occurrence. An equivalent thermal resistance model was proposed to elucidate the same. Additionally, the heat transfer coefficient reduces (HTDn) near the outlet at higher roughness values where HTD has completely recovered. This is attributed to the high specific heat value around the pseudocritical temperature. In the end, the efficacy of the roughness was analyzed using two methods: entropy generation and thermal performance factor. Both techniques suggest that the use of rough pipe is beneficial. However, the first method recommends using a Ks value greater than the critical roughness height (Ksc): as the total entropy generation was found to peak at Ksc because of the thermal conductivity variation with temperature. The study revealed high sensitivity of maximum wall temperature and HTD onset to roughness presence. In addition, contrary to usual HTD, a new type of heat transfer impairment (HTDn) can occur without any loss of TKE.

physics.flu-dyn↗

arXiv2021

On the Thermofluidics of a Steady Laminar Jet Impacting on a Rotating Hot Plate: An ab-initio Scaling Perspective

We provide an ab-initio scaling analysis for liquid film thickness and Nusselt number of a steady laminar jet impacting a rotating heated plate. The limiting scaling regimes incorporating the evaporative effects along the liquid-vapor interface have been probed. The dependence of liquid film thickness and Nusselt number on Reynolds, Rossby, and Prandtl number have been unearthed using scaling analysis of the integral and differential form of the continuity, Navier-Stokes and energy equation in a cylindrical coordinate system. Boundary layer analysis has been used to discover a critical length that plays a significant role in understanding the effect of evaporation on hydrodynamic, thermal boundary layer thicknesses, and subsequently Nusselt number. The evaporative effects on liquid film thickness become increasingly important after a certain critical radius. The scaling laws derived were compared with existing experimental data available in the literature, and the trends predicted were consistent.

physics.flu-dyn↗

arXiv2021

Laser pulse-droplet interaction enables the deformation and fragmentation of droplet array

Droplet-droplet interactions is ubiquitous in various applications ranging from medical diagnostics to enhancing and optimizing liquid jet propulsion. We employ an experimental technique where the laser pulse interacts with a micron-sized droplet and causes optical breakdown. The synergy of a nanosecond laser pulse and an isolated spherical droplet is accurately controlled and manipulated to influence the deformation and fragmentation of an array of droplets. We elucidate how the fluid dynamic response (such as drop-drop and shock-drop interactions) of an arrangement of droplets can be regulated and optimally shaped by laser pulse energy and its interplay with the optical density of liquid target. A new butterfly type breakup is revealed, which is found to result in controlled and efficient fragmentation of the outer droplets in an array. The spatio-temporal characteristics of a laser-induced breakdown dictate how shock wave and central droplet fragments can influence outer droplets. The incident laser energy and pulse width employed in this work are representative of diverse industrial applications such as surface cleaning, nano-lithography, microelectronics, and medical procedures such as intraocular microsurgery.

physics.flu-dyn↗

arXiv2020

Novel two-phase method for supercritical water flow

The current resurgence in the phase diagram study beyond the critical point has questioned the conventional belief of supercritical fluid as a single phase with varying properties. On the same line, a novel two-phase approach has been proposed to study the supercritical flow with heat transfer deterioration (HTD) phenomena. The Volume of Fluid (VOF) multiphase model has been used to analyze the flow, and the simulation result reasonably predicts the wall temperature peaks. Moreover, the velocity and turbulent kinetic energy profiles for different axial locations explain the occurrence of HTD, and it is on par with the pre-existing numerical method. Besides, the quantitative analysis presented in the paper expounds on qualitative understanding. The parametric study of the thermophysical properties revealed that the density variation is the primary cause of HTD in supercritical flows. So banking on this conclusion, the propounded study focuses on the forces generated due to the density variation. This technique equips us with a holistic picture of the supercritical flows. It leads to the inference that for no HTD effects to be present, buoyancy and inertia forces have to be of comparable magnitude throughout the flow. In addition, the pseudo phase change model outclasses the existing research by rendering us the volume fraction data. Mapping of this variable reveals a sudden jump in the lighter phase's thickness near the wall at the site of HTD, which is also reflected as a maximum in the nondimensional two-phase thickness (P) plot. Nevertheless, this observation is only restricted to HTD caused by buoyancy. In the end, a theoretical expression has been conceptualized for computing the two-phase thickness (h) value, which can serve as a fundamental length scale in supercritical flows as it marks the region of highest property gradient near the wall.

physics.flu-dyn↗

arXiv2020

Dynamics of Droplet Generation from Corneal Tear Film during Non-contact Eye Procedure in the Context of COVID-19

Non-invasive medical diagnostics demonstrate a propensity for droplet generation and should be studied to devise risk mitigation strategies against the spread of the SARS-CoV-2 virus. We investigate the air-puff tonometry, which uses a short-timed air-puff to applanate the human eye in a bid to detect the early onset of glaucoma by measuring the intraocular pressure. The air-puff consists of a vortex trailed by a high-speed jet. High-speed imaging of the eye during a typical tonometry measurement reveals a sequence of events starting with the interaction between the tear layer and the air puff leading to an initial sheet ejection. It is immediately followed by the trailing jet applanating the central corneal section, causing capillary waves to form and interact with the highly 3D transient expanding sheet. Such interaction with the capillary waves and the surrounding airfield due to the trailing jet causes the expanding sheet to undergo bag breakup, finger formation by Rayleigh Taylor instability and further break up into subsequent droplets by Rayleigh Plateau instability, which eventually splashes onto nearby objects, potentially forming fomites or aerosols which can lead to infections. The complex spatiotemporal phenomenon is carefully documented by rigorous experiments and corroborated using comprehensive theoretical analyses.

physics.med-ph↗

arXiv2020

On Secondary Atomization and blockage of surrogate cough droplets in single and multi-layer face masks

By now it is well-understood that the usage of facemasks provides protection from transmission of viral loads through exhalation and inhalation of respiratory droplets. Therefore, during the current Covid-19 pandemic the usage of face masks is strongly recommended by health officials. Although three-layer masks are generally advised for usage, many commonly available or homemade masks contain only single and double layers. In this study, we show through detailed physics based analyses and high speed imaging that high momentum cough droplets on impingement on single- and double-layer masks can lead to significant partial penetration and more importantly atomization into numerous much smaller daughter droplets, thereby increasing the total population of the aerosol, which can remain suspended for a longer time. The possibility of secondary atomization of high momentum cough droplets due to impingement, hydrodynamic focusing and extrusion through the microscale pores in the fibrous network of the mask has not been explored before. However, this unique mode of aerosol generation poses a finite risk of infection as shown in this work. We also demonstrate that in single layer masks close to 70 % of a given droplet volume is atomized and only 30 % is trapped within the fibers. The entrapped volume is close to 90 % for double layer masks which still allows some atomization into smaller droplets. We however found that a triple-layer surgical mask permits negligible penetration and hence should be effective in preventing disease transmission.

physics.app-ph↗

arXiv2020

Analyzing the dominant SARS-CoV-2 transmission routes towards an ab initio SEIR model

Identifying the relative importance of the different transmission routes of the SARS-CoV-2 virus is an urgent research priority. To that end, the different transmission routes, and their role in determining the evolution of the Covid-19 pandemic are analyzed in this work. Probability of infection caused by inhaling virus-laden droplets (initial, ejection diameters between $0.5-750μm$) and the corresponding desiccated nuclei that mostly encapsulate the virions post droplet evaporation, are individually calculated. At typical, air-conditioned yet quiescent indoor space, for average viral loading, cough droplets of initial diameter between $10-50 μm$ have the highest infection probability. However, by the time they are inhaled, the diameters reduce to about $1/6^{th}$ of their initial diameters. While the initially near unity infection probability due to droplets rapidly decays within the first $25s$, the small yet persistent infection probability of desiccated nuclei decays appreciably only by $\mathcal{O} (1000s)$, assuming the virus sustains equally well within the dried droplet nuclei as in the droplets. Combined with molecular collision theory adapted to calculate frequency of contact between the susceptible population and the droplet/nuclei cloud, infection rate constants are derived ab-initio, leading to a SEIR model applicable for any respiratory event - vector combination. Viral load, minimum infectious dose, sensitivity of the virus half-life to the phase of its vector and dilution of the respiratory jet/puff by the entraining air are shown to mechanistically determine specific physical modes of transmission and variation in the basic reproduction number $\mathcal{R}_0$, from first principle calculations.

q-bio.PE↗

arXiv2020

Insights on drying and precipitation dynamics of respiratory droplets in the perspective of Covid-19

We isolate a nano-colloidal droplet of surrogate mucosalivary fluid to gain fundamental insights into the infectivity of air borne nuclei during the Covid-19 pandemic. Evaporation experiments are performed with salt-water solutions seeded with a viral load of inactive nanoparticles in an acoustic levitator. We seek to emulate the drying, flow and precipitation dynamics of such air borne mucosalivary droplets. Observations with the surrogate fluid are validated by similar experiments with actual samples from a healthy subject. A unique feature emerges with regards to the final crystallite dimension; it is always 20-30% of the initial droplet diameter for different sizes and ambient conditions. The preserved precipitates from levitated droplets show that 15% of the total virion population remain dispersed on the outer surface of air-desiccated air borne nuclei. This fraction increases to ~90% if the respiratory droplets (of larger initial size) settle on a surface and then evaporate in the sessile mode.

cond-mat.soft↗

arXiv2020

Universal dissolution dynamics of a confined sessile droplet

We experimentally investigate the dissolution of microscale sessile alcohol droplets in water under the influence of impermeable vertical confinement. The introduction of confinement suppresses the mass transport from the droplet to bulk medium in comparison with the non-confined counterpart. Along with a buoyant plume, flow visualization reveals that the dissolution of a confined droplet is hindered by a newly identified mechanism - levitated toroidal vortex. The morphological changes in the flow due to the vortex-induced impediment alters the dissolution rate, resulting in enhancement of droplet lifetime. Further, we have proposed a modification in the key non-dimensional parameters (Rayleigh number $Ra^{'}$ (signifying buoyancy) and Sherwood number $Sh^{'}$ (signifying mass flux)) and droplet lifetime $τ_{c}^{'}$, based on the hypothesis of linearly stratified droplet surroundings (with revised concentration difference $ΔC^{'}$), taking into account the geometry of the confinements. We show that experimental results on droplet dissolution under vertical confinement corroborate universal scaling relations $Sh^{'} \sim Ra^{' 1/4}$ and $τ_{c}^{'} \sim ΔC^{'-5/4}$. We also draw attention to the fact that the revised scaling law incorporating the geometry of confinements proposed in the present work can be extended to other known configurations such as droplet dissolution inside a range of channel dimensions, as encountered in a gamut of applications such as micro-fluidic technology and biomedical engineering.

physics.flu-dyn↗

arXiv2020

Modeling ambient temperature and relative humidity sensitivity of respiratory droplets and their role in Covid-19 outbreaks

One of the many unresolved questions that revolves around the Covid-19 pandemic is whether local outbreaks can depend on ambient conditions like temperature and relative humidity. In this paper, we develop a model that tries to explain and describe the temperature and relative humidity sensitivity of respiratory droplets and their possible connection in determining viral outbreaks. The model has two parts. First, we model the growth rate of the infected population based on a reaction mechanism - the final equations of which are similar to the well-known SIR model. The advantage of modeling the pandemic using the reaction mechanism is that the rate constants have sound physical interpretation. The infection rate constant is derived using collision rate theory and shown to be a function of the respiratory droplet lifetime. In the second part, we have emulated the respiratory droplets responsible for disease transmission as salt solution droplets and computed their evaporation time accounting for droplet cooling, heat and mass transfer and finally crystallization of the salt. The model output favourably compares with the experimentally obtained evaporation characteristics of levitated droplets of pure water and salt solution, respectively, ensuring fidelity of the model. Droplet evaporation/desiccation time is indeed dependent on ambient temperature and relative humidity, considered at both outdoor and indoor conditions. Since the droplet evaporation time determines the infection rate constant, ambient temperature and relative humidity are shown to impact the outbreak growth rates.

physics.flu-dyn↗

arXiv2020

Atomization modes for levitating emulsified droplets undergoing phase change

We delineate and examine the distinct breakup modes of evaporating water-in-oil emulsion droplets under acoustic levitation. The emulsion droplets consist of decane/dodecane/tetradecane as oil, while the water concentration is varied from 10% to 30% (v/v). The droplets were heated under different laser irradiation intensities and were observed to exhibit three broad breakup mechanisms, viz., breakup through bubble growth, sheet breakup, and catastrophic breakup. The occurrence of these modes of the breakup is found to be primarily dependent on the volatility differential among the components. Early nucleation in water/decane emulsions results in the growth of vapor bubble, which is characterized by intricate patterns of wave propagation on the droplet surface. The formation of these patterns suggests that the short time scale and length scale of wave patterns is the manifestation of Faraday instability, triggered on the droplet surface by the acoustic field induced resonance. A sheet-like breakup, on the contrary, occurs predominantly in emulsions comprising of components with relatively high volatility difference (water/dodecane emulsions) due to the breakup of an indiscernible small sized bubble. Intense catastrophic breakup occurs for emulsions with significantly vast volatility difference (water/tetradecane emulsions) where the droplet undergoes prompt fragmentation into fine secondary droplets.

physics.flu-dyn↗

arXiv2020

Phenomenology of disruptive breakup mechanism of a levitated evaporating emulsion droplet

Atomization of emulsion droplets is ubiquitous across a variety of application domains ranging from NextGen combustors to fabrication of biomedical implants. An understanding of the atomization mechanism in emulsions can result in a paradigm shift in customized designs of efficient systems, be it in energy or biotechnology sectors. In this paper, we specifically study the breakup mechanism of an evaporating contact-free (acoustic levitation) emulsion droplet (water-oil) under external heating. Three distinct regimes are observed during the lifespan of the evaporating droplet. Initially, the droplet diameter regresses linearly with time, followed by vapor bubble nucleation due to a significant difference in the boiling temperature among the components of the emulsion. The collapse of this bubble results in a high-intensity breakup of the droplet leading to the propulsion of residual liquid in the form of a crown-like sheet. The area of the expanding crown varies linearly with the square of the time. It is hypothesized that the expansion of the liquid sheet centrifuges the larger water sub-droplets towards the edge, resulting in unique spatial segregation. Subsequently, we report the first observation of complex patches (representing water sub-droplets) and the rupture of the thin sheet adjacent to patches into holes (with hole growth rate ranging from 1.2 to 1.4 m/s) in the context of an evaporating isolated emulsion droplet. The hole formation results in the creation of ligaments which undergo breakup into secondary droplets with Sauter mean diameter (SMD) ~ 50 μm.

physics.flu-dyn↗

arXiv2019

Generalizing Co-operative Evaporation in Two-Dimensional Droplet Arrays

Sessile droplets exposed to an incipient condition lead to an inevitable loss of mass, which is critical in many practical applications. By considering an arbitrarily configured two-dimensional array of droplets, here we provide a simple generalized theoretical limit to their lifetime in an evaporating state. Notwithstanding the geometrical and physical complexity of the effective confinement generated due to their cooperative interactions, we show that the consequent evaporation characteristics may be remarkably insensitive to the topographical details of the overall droplet organization, for a wide range of droplet-substrate combinations. With subsequent deployment of particle-laden droplets, however, our results lead to the discovery of a unique pathway towards tailoring the internal flows within the collective system by harnessing an exclusive topologically-driven symmetry breaking phenomenon, yielding a new strategy of patterning particulate matters around the droplet array.

physics.flu-dyn↗

arXiv2010

Structure formation by nanosilica particles suspended in levitated droplet

Vaporization of liquid droplets containing particles has been studied extensively for its applications in combustion, thermal coating, ink-jet printing, spray cooling, drug delivery, and surface patterning. Droplets containing solid particles show a preferential solute-migration during drying process. Recently we carried out experiments with vaporizing droplet suspended in an acoustic levitator. In this work, we present detailed study of a laser irradiated droplet containing nanosilica particles. Infrared and High speed imaging of the heating process for different concentrations of nanosilica revealed an interesting solute migration pattern. Further investigation with Particle Image Velocimetry shows presence of strong recirculation within the levitated droplet. It also reveals that with increasing viscosity of the liquid the strength of this recirculation decreases. Due to the droplets rotation about the levitator axis, a centrifugal force also dominated the flow field within the droplet. High speed imaging shows that initial stage of heating is dominated by sharper diameter reduction. At the end of this stage the droplet takes a bowl shape. Next stage, which is termed as structure formation shows different characteristics for higher and lower concentrations. For nanosilica concentration of less than 1.3%, the bowl shape remains unaltered with further heating. On the other hand, for concentration greater than 1.9%, due to stronger centrifugal effect than recirculation, the particles migrate towards the equator plane creating horizontal ring structure. The horizontal ring very soon starts oscillating about the levitator axis. This creates an imbalance of forces resulting in reorientation of the ring. Thus a vertical ring is created.

physics.flu-dyn↗