arXiv subjects

S. Rowan

Publications and source records attributed to S. Rowan.

9 recordsLinked to original sources

arXiv2025

Low thermal noise mirror coatings utilising titanium dioxide and germanium dioxide mixtures

Upgrades to ground-based gravitational-wave observatories will require mirror coatings with reduced thermal noise, enabling improved detector sensitivity and extended astrophysical reach. Recent studies have shown that optical coatings utilising amorphous materials that exhibit a larger fraction of corner-sharing between adjacent structural units of metal-centered polyhedra are a promising route for reducing mechanical dissipation and thus thermal noise at room temperature. We report on multilayer optical coatings that are fabricated using germanium dioxide mixed with titanium dioxide (TiO$_2$:GeO$_2$) for the high index layers, and silicon dioxide (SiO$_2$) for the low index material. Single layers of TiO$_2$:GeO$_2$ are characterised to optimise the mixture proportion and based on that highly reflective multilayer stacks were deposited. Exceptional optical absorption at 1064 nm below 1 part-per-million (ppm) is observed in the multilayer stacks after heat treatment. The annealing process also induces the formation of blisters which leads to increased optical scattering. However, there is indication that blisters can be suppressed by decreasing the water partial pressure in the deposition chamber. Direct thermal noise measurements provide experimental verification of a significant 25\% reduction of thermal noise over the mirrors currently employed, which combined with sub-ppm levels of optical absorption show the potential of TiO$_2$:GeO$_2$ to improve the sensitivity of gravitational-wave observatories.

physics.ins-det↗

arXiv2021

Proposed large scale monolithic fused silica mirror suspension for 3rd generation gravitational wave detectors

Thermal noise from the suspension fibres used in the mirror pendulums in current gravitational wave detectors is a critical noise source. Future detectors will require improved suspension performance with the specific ability to suspend much heavier masses to reduce radiation pressure noise, whilst retaining good thermal noise performance. In this letter, we propose and experimentally demonstrate a design for a large-scale fused silica suspension, demonstrating its suitability for holding an increased mass of 160 kg. We demonstrate the concepts for improving thermal noise via longer suspension fibres supporting a higher static stress. We present a full thermal noise analysis of our prototype, meeting requirements for conceptual 3rd generation detector designs such as the high frequency interferometer of the Einstein Telescope (ET-HF), and closely approaching that required for Cosmic Explorer (CE).

astro-ph.IM↗

arXiv2021

Exploration of co-sputtered Ta$_2$O$_5$-ZrO$_2$ thin films for gravitational-wave detectors

We report on the development and extensive characterization of co-sputtered tantala-zirconia thin films, with the goal to decrease coating Brownian noise in present and future gravitational-wave detectors. We tested a variety of sputtering processes of different energies and deposition rates, and we considered the effect of different values of cation ratio $\eta =$ Zr/(Zr+Ta) and of post-deposition heat treatment temperature $T_a$ on the optical and mechanical properties of the films. Co-sputtered zirconia proved to be an efficient way to frustrate crystallization in tantala thin films, allowing for a substantial increase of the maximum annealing temperature and hence for a decrease of coating mechanical loss. The lowest average coating loss was observed for an ion-beam sputtered sample with $\eta = 0.485 \pm 0.004$ annealed at 800 $^{\circ}$C, yielding $\overline{\varphi} = 1.8 \times 10^{-4}$. All coating samples showed cracks after annealing. Although in principle our measurements are sensitive to such defects, we found no evidence that our results were affected. The issue could be solved, at least for ion-beam sputtered coatings, by decreasing heating and cooling rates down to 7 $^{\circ}$C/h. While we observed as little optical absorption as in the coatings of current gravitational-wave interferometers (0.5 parts per million), further development will be needed to decrease light scattering and avoid the formation of defects upon annealing.

physics.ins-det↗

arXiv2011

Increased Brownian force noise from molecular impacts in a constrained volume

We report on residual gas damping of the motion of a macroscopic test mass enclosed in a nearby housing in the molecular flow regime. The damping coefficient, and thus the associated thermal force noise, is found to increase significantly when the distance between test mass and surrounding walls is smaller than the test mass itself. The effect has been investigated with two torsion pendulums of different geometry and has been modelled in a numerical simulation whose predictions are in good agreement with the measurements. Relevant to a wide variety of small-force experiments, the residual-gas force noise power for the test masses in the LISA gravitational wave observatory is roughly a factor 15 larger than in an infinite gas volume, though still compatible with the target acceleration noise of 3 fm s^-2 Hz^-1/2 at the foreseen pressure below 10^-6 Pa.

gr-qc↗

arXiv2010

Investigation of mechanical losses of thin silicon flexures at low temperatures

The investigation of the mechanical loss of different silicon flexures in a temperature region from 5 to 300 K is presented. The flexures have been prepared by different fabrication techniques. A lowest mechanical loss of $3\times10^{-8}$ was observed for a 130 $μ$m thick flexure at around 10 K. While the mechanical loss follows the thermoelastic predictions down to 50 K a difference can be observed at lower temperatures for different surface treatments. This surface loss will be limiting for all applications using silicon based oscillators at low temperatures. The extraction of a surface loss parameter using different results from our measurements and other references is presented. We focused on structures that are relevant for gravitational wave detectors. The surface loss parameter $α_s$ = 0.5 pm was obtained. This reveals that the surface loss of silicon is significantly lower than the surface loss of fused silica.

cond-mat.mtrl-sci↗

arXiv2005

Mechanical Dissipation in Silicon Flexures

The thermo-mechanical properties of silicon make it of significant interest as a possible material for mirror substrates and suspension elements for future long-baseline gravitational wave detectors. The mechanical dissipation in 92um thick <110> single-crystal silicon cantilevers has been observed over the temperature range 85 K to 300 K, with dissipation approaching levels down to phi = 4.4E-7.

gr-qc↗

arXiv2004

Thermoelastic dissipation in inhomogeneous media: loss measurements and displacement noise in coated test masses for interferometric gravitational wave detectors

The displacement noise in the test mass mirrors of interferometric gravitational wave detectors is proportional to their elastic dissipation at the observation frequencies. In this paper, we analyze one fundamental source of dissipation in thin coatings, thermoelastic damping associated with the dissimilar thermal and elastic properties of the film and the substrate. We obtain expressions for the thermoelastic dissipation factor necessary to interpret resonant loss measurements, and for the spectral density of displacement noise imposed on a Gaussian beam reflected from the face of a coated mass. The predicted size of these effects is large enough to affect the interpretation of loss measurements, and to influence design choices in advanced gravitational wave detectors.

gr-qc↗

arXiv2001

Excess Mechanical Loss Associated with Dielectric Mirror Coatings on Test Masses in Interferometric Gravitational Wave Detectors

Interferometric gravitational wave detectors use mirrors whose substrates are formed from materials of low intrinsic mechanical dissipation. The two most likely choices for the test masses in future advanced detectors are fused silica or sapphire. These test masses must be coated to form mirrors, highly reflecting at 1064nm. We have measured the excess mechanical losses associated with adding dielectric coatings to substrates of fused silica and calculate the effect of the excess loss on the thermal noise in an advanced interferometer.

gr-qc↗

arXiv1999

Toward gravitational wave detection

An overview of some tools and techniques being developed for data conditioning (regression of instrumental and environmental artifacts from the data channel), detector design evaluation (modeling the science ``reach'' of alternative detector designs and configurations), noise simulations for mock data challenges and analysis system validation, and analyses for the detection of gravitational radiation from gamma-ray burst sources.

gr-qc↗