arXiv subjects

S. Berns

Publications and source records attributed to S. Berns.

5 recordsLinked to original sources

arXiv2026

A new diffuse reflector filament for additive manufacturing of 3D printing finely-segmented plastic scintillator

This study presents the development and the characterization of novel white reflective filaments suitable for additive manufacturing of finely segmented plastic scintillators. The filament is based on polycarbonate (PC) and polymethyl methacrylate (PMMA) polymers loaded with titanium dioxide (TiO$_2$) and polytetrafluoroethylene (PTFE) to enhance reflectivity. A range of filament compositions and thicknesses was evaluated through optical reflection and transmittance measurements of reflective layers made with the Fused Deposition Modeling (FDM) technique. A 3D-segmented plastic scintillator prototype was made with fused injection modeling (FIM) and tested with cosmic rays to assess the light yield and the optical crosstalk. The results demonstrate the feasibility of producing compact and modular 3D-printed scintillator detectors with a performance analogous to standard plastic scintillator detectors. Owing to the improved optical properties of the new reflector filament, a lower light crosstalk and a higher light yield, compared to past works, is obtained.

physics.ins-det↗

arXiv2025

A new diffuse reflector filament for additive manufacturing of 3D printing finely-segmented plastic scintillator

This study presents the development and characterization of a novel white reflective filament suitable for additive manufacturing of finely segmented plastic scintillators using 3D printing. The filament is based on polycarbonate (PC) and polymethyl methacrylate (PMMA) polymers loaded with titanium dioxide (TiO$_2$) and polytetrafluoroethylene (PTFE) to enhance reflectivity. A range of filament compositions and thicknesses was evaluated through optical reflection and transmittance measurements. Reflective layers were made by using the Fused Deposition Modeling (FDM) technique. A 3D-segmented plastic scintillator prototype was made with fused injection modeling (FIM) and tested with cosmic rays to assess the light yield and the optical crosstalk. The results demonstrate the feasibility of producing compact and modular 3D-printed scintillator detectors with a performance analogous to standard plastic scintillator detectors, with lower light crosstalk, thus higher light yield, compared to past works, owing to the improved optical properties of the reflector material.

physics.ins-det↗

arXiv2022

Additive manufacturing of inorganic scintillator-based particle detectors

Inorganic scintillators are widely used for scientific, industrial and medical applications. The development of 3D printing with inorganic scintillators would allow fast creation of detector prototypes for registration of ionizing radiation, such as alpha and beta, gamma particles in thin layers of active material and soft X-ray radiation. This article reports on the technical work and scientific achievements that aimed at developing a new inorganic scintillation filament to be used for the 3D printing of composite scintillator materials: study and definition of the scintillator composition; development of the methods for the inorganic scintillator filament production and further implementation in the available 3D printing technologies; study of impact of the different 3D printing modes on the material scintillation characteristics. Also, 3D printed scintillators can be used for creation of combined detectors for high-energy physics.

physics.ins-det↗

arXiv2022

Additive manufacturing of fine-granularity optically-isolated plastic scintillator elements

Plastic scintillator detectors are used in high energy physics as well as for diagnostic imaging in medicine, beam monitoring on hadron therapy, muon tomography, dosimetry and many security applications. To combine particle tracking and calorimetry it is necessary to build detectors with three-dimensional granularity, i.e. small voxels of scintillator optically isolated from each other. Recently, the 3DET collaboration demonstrated the possibility to 3D print polystyrene-based scintillators with a light output performance close to that obtained with standard production methods. In this article, after providing a further characterization of the developed scintillators, we show the first matrix of plastic scintillator cubes optically separated by a white reflector material entirely 3D printed with fused deposition modeling. This is a major milestone towards the 3D printing of the first real particle detector. A discussion of the results as well as the next steps in the R&D is also provided.

physics.ins-det↗

arXiv2020

A novel polystyrene-based scintillator production process involving additive manufacturing

Plastic scintillator detectors are widely used in particle physics thanks to the very good particle identification, tracking capabilities and time resolution. However, new experimental challenges and the need for enhanced performance require the construction of detector geometries that are complicated using the current production techniques. In this article we propose a new production technique based on additive manufacturing that aims to 3D print polystyrene-based scintillator. The production process and the results of the scintillation light output measurement of the 3D-printed scintillator are reported.

physics.ins-det↗