arXiv subjects

R. Xu

Publications and source records attributed to R. Xu.

At least 19 recordsLinked to original sources

arXiv2026

Transient fluid removal at soft interfaces: Contact-time-controlled squeeze-out in a cylinder-on-flat contact

We study transient fluid removal in cylinder-on-flat contacts between stiff PMMA cylinders and a soft PDMS substrate. The cylinder geometry eliminates the edge-scraping mechanism that can occur for deformable rubber blocks, allowing the influence of sliding on fluid squeeze-out to be examined more directly. Experiments were performed mainly in glycerol at the low sliding speed $v=3 \ {\rm \mu m/s}$ using cylinders with different surface roughness. After the initial elastic-loading stage, we find that the friction during sliding depends primarily on the total time elapsed since application of the normal load rather than on the preceding sliding distance. The subsequent friction evolution follows approximately the same dependence on total contact time. Stationary squeeze-out calculations predict the evolution of the mean surface separation and real contact area, in reasonable agreement with that inferred from the measured friction. These results show that essentially the same squeeze-out process governs fluid removal during stationary contact and low-speed sliding, and that sliding-induced elastohydrodynamic effects have only a minor influence under these conditions.

cond-mat.soft↗

arXiv2026

Transient fluid removal at soft interfaces: Stationary squeeze-out and dynamic scraping in a block-on-flat contact

Fluid removal from rubber-substrate interfaces is crucial for maintaining friction during walking and vehicle braking on contaminated surfaces. We study the transient friction of rectangular rubber blocks sliding against tile and glass surfaces lubricated with water, glycerol, mud, or silicone grease. Two block configurations with different lengths in the sliding direction were tested after different stationary waiting times. For water, stationary squeeze-out is nearly complete before sliding begins. For glycerol, both stationary squeeze-out and sliding-induced fluid removal are important. For mud and grease, the steady-sliding state is reached after a sliding distance of the order of the block length, with little dependence on the preceding waiting time, showing that sliding-induced scraping dominates fluid removal for highly viscous substances. Dividing the contact into shorter blocks accelerates fluid removal by reducing the drainage distance and increasing the number of leading edges. Stationary squeeze-out calculations based on the measured surface roughness are in reasonably good agreement with the glycerol experiments. The results provide design guidelines for rubber tread blocks with multiscale drainage channels and sufficient compliance to promote transient fluid removal.

cond-mat.soft↗

arXiv2026

Hierarchies of No-regret Algorithms

Our paper studies the setting of players using no-regret algorithms in various two-player games. We address whether having stronger regret guarantees or playing against an opponent with weaker regret guarantees yields higher utilities for the player in question. We consider a hierarchy of algorithms from weakest to strongest: uniform random play, no-regret, and no-swap-regret. We find, counterintuitively, that in many games, no-swap-regret is a worse choice for players (and gives better utility for their opponents). We find the root cause of this phenomenon to be a difference in effective learning rate between the two algorithms, where the no-swap-regret algorithms learn $N$ times slower than no-regret algorithms. To address this, we attempt to equalize learning rates, leading to closer utility between no-regret and no-swap-regret players. Finally, we show that for certain random games with $7$ actions per player, no-swap-regret algorithms can perform noticeably better than no-regret algorithms in a manner that cannot be explained away by unfairly adjusted learning rates.

cs.GT↗

arXiv2026

Role of transfer films and interfacial cracking in metallic sliding wear

The origin of wear particles in metallic sliding contacts remains debated. Classical views based on cold-welded junctions suggest that plastic yielding of the real contact area should lead to large wear coefficients, in apparent contradiction with the small values typically measured for metals. Here we argue that this discrepancy can be resolved if most junctions do not directly produce wear particles, but instead cause metal transfer and the formation of a weakly bound transfer film. Wear then occurs intermittently when fragments of this film detach due to crack propagation at the interface between the transfer film and the underlying bulk metal. We perform unlubricated reciprocating sliding experiments on nominally smooth stainless steel, brass, and aluminum. For steel on steel, the wear mass loss shows an initial stage with negligible mass change up to a sliding distance of $\sim 2.4 \ {\rm m}$, followed by a linear regime. Transfer-film formation in dissimilar-metal contacts is evidenced by optical imaging, net mass gain of the steel slider, and energy-dispersive X-ray spectroscopy, and the collected debris is flake-like. These observations support a transfer-film-controlled wear mechanism associated with cold-welded junctions.

cond-mat.soft↗

arXiv2026

Search for Cosmic Ray Electron Boosted Dark Matter with the CDEX-10 Experiment

We present new constraints on the cosmic ray electron boosted light dark matter (CReDM) using the 205.4 kg$\cdot$day data of the CDEX-10 experiment located at the China Jinping Underground Laboratory. The cosmic ray electron spectrum and distribution in the Galaxy are generated by the $\tt GALPROP$ code package. In the calculation process of DM-electron scattering process in the Galaxy, we consider the energy-dependency of the DM-electron scattering cross section. The constraints on CReDM are set for both heavy and light mediator scenarios using the CDEX-10 dataset. The result exceeds previous Standard Halo Model (SHM) limits for DM mass lower than 0.6 MeV in heavy mediator case and corresponds to the best sensitivity among all direct detection experiments from 1 keV to 0.5 MeV in the light mediator scenario.

hep-ex↗

arXiv2025

Constraints on ultraheavy dark matter from the CDEX-10 experiment at the China Jinping Underground Laboratory

We report a search for ultraheavy dark matter (UHDM) with the CDEX-10 experiment at the China Jinping Underground Laboratory. Using a Monte Carlo framework that incorporates Earth shielding effects, we simulated UHDM propagation and energy deposition in p-type point-contact germanium detectors. Analysis of 205.4 kg$\cdot$day exposure in the 0.16--4.16 keVee range showed no excess above background. Our results exclude the spin-independent UHDM-nucleon scattering with two cross section scales, with the UHDM mass from $10^6$ to $10^{11}$ GeV, and provide the most stringent constraints with solid-state detectors below $10^8$ GeV.

hep-ex↗

arXiv2025

Constraints on inelastic dark matter from the CDEX-1B experiment

We present limits on spin-independent inelastic weakly interacting massive particles (WIMP)-nucleus scattering using the 737.1 kg$\cdot$day dataset from the CDEX-1B experiment. Expected nuclear recoil spectra for various inelastic WIMP masses $m_\chi$ and mass splittings $\delta$ are calculated under the standard halo model. An accurate background model of CDEX-1B is constructed by simulating all major background sources. The model parameters are then determined through maximum likelihood estimation and Markov chain Monte Carlo fitting. The resulting 90\% confidence level upper limits on the WIMP-nucleon cross section $\sigma_{\mathrm{n}}$ exclude certain DAMA/LIBRA allowed regions: the $\chi^2 < 4$ regions for $\delta < 30$ keV at $m_\chi = 250$ GeV and the $\chi^2 < 9$ region for $\delta < 50$ keV at $m_\chi = 500$ GeV. The method is applicable to other inelastic dark matter scenarios, and the upcoming CDEX-50 experiment is expected to improve sensitivity by four orders of magnitude.

hep-ex↗

arXiv2025

Rubber Friction: Theory, Mechanisms, and Challenges

Rubber friction is of major practical importance in applications such as tires, rubber seals, and footwear. This review article focuses on the theory and experimental studies of rubber friction on substrates with random roughness. We examine both steady sliding and accelerated motion, with particular attention to the origins of the breakloose friction force and the influence of pre-slip, elasticity, and flash temperature on friction dynamics. We further discuss rolling friction for cylinders and spheres, as well as sliding friction for triangular sliders on dry and lubricated rubber surfaces. Theoretical predictions are compared with experimental results obtained using different materials, geometries, and environmental conditions, highlighting the importance of accounting for multiscale roughness. Open challenges, such as the role of adhesion enhancement, energy dissipation due to crack opening, and the physical origin of the short-distance roughness cut-off, are discussed.

cond-mat.soft↗

arXiv2025

Leakage at interfaces: a comprehensive study based on Persson contact mechanics theory

We present a comprehensive study of gas leakage at interfaces based on Persson contact mechanics theory. A prototype syringe system consisting of a rubber stopper and a glass barrel is selected, where surface roughness is characterized using measurements from stylus profilometry and atomic force microscopy, and contact pressure distributions are obtained from Finite Element Method (FEM) calculations. Leakage prediction is performed using Multiscale Contact Mechanics (MCM) software. The predicted results show good agreement with experimental measurements under controlled dry conditions. Sensitivity analyses indicate that small variations in elastic modulus and contact pressure can significantly influence leakage, particularly near the percolation threshold. This work provides a generalized and validated framework for leakage prediction and offers practical guidance for the design of sealing systems in pharmaceutical and engineering applications.

cond-mat.soft↗

arXiv2025

Photoabsorption Cross Sections studied within the axially deformed Relativistic Quasiparticle Finite Amplitude Framework

Photoabsorption cross sections for 235 stable nuclei, ranging from $^{40}$Ca to $^{209}$Bi, were investigated by the quasiparticle finite amplitude method (QFAM) based on the axially deformed relativistic Hartree-Bogoliubov (RHB) approach using relativistic point-coupling interaction DD-PC1, with extensions to odd-A nuclei. GDR parameters based on the standard Lorentzian (SLO) model were extracted from QFAM results and compared with those from experimental data recommended by IAEA. Good agreement was achieved for giant dipole resonance (GDR) peak energies, while resonance widths were underestimated and hence peak cross sections were overestimated due to the lack of higher-order many-body correlations. These discrepancies were much improved in deformed nuclei. The effects of deformation on photoabsorption cross sections were examined systematically. The comparison of photoabsorption cross sections among QFAM results and discrepant experimental data revealed the potential of QFAM calculations in the evaluation of photonuclear data.

nucl-th↗

arXiv2025

Sliding Friction of Hard Sliders on Rubber: Theory and Experiment

We present a study of sliding friction for rigid triangular steel sliders on soft rubber substrates under both lubricated and dry conditions. For rubber surfaces lubricated with a thin film of silicone oil, the measured sliding friction at room temperature agrees well with theoretical predictions obtained from a viscoelastic model originally developed for rolling friction. On the lubricated surface, the sliding friction is primarily due to bulk viscoelastic energy dissipation in the rubber. The model, which includes strain-dependent softening of the rubber modulus, accurately predicts the experimental friction curves. At lower temperatures ($T = -20^\circ {\rm C}$ and $-40^\circ {\rm C}$), the measured friction exceeds the theoretical prediction. We attribute this increase to penetration of the lubricant film by surface asperities, leading to a larger adhesive contribution. For dry surfaces, the adhesive contribution becomes dominant. By subtracting the viscoelastic component inferred from the lubricated case, we estimate the interfacial frictional shear stress. This shear stress increases approximately linearly with the logarithm of the sliding speed, consistent with stress-augmented thermal activation mechanisms.

cond-mat.soft↗

arXiv2025

Constraints on dark matter boosted by supernova shock within the effective field theory framework from the CDEX-10 experiment

Supernova shocks can boost dark matter (DM) particles to high, yet nonrelativistic, velocities, providing a suitable mechanism for analysis within the framework of the nonrelativistic effective field theory (NREFT). These accelerated DM sources extend the experimental ability to scan the parameter space of light DM into the sub-GeV region. In this study, we specifically analyze DM accelerated by the Monogem Ring supernova remnant, whose age ($\sim 68000$ yr) and distance to Earth ($\sim 300$ parsec) are strategically matched to enable detection with current terrestrial detectors. Utilizing the 205.4 kg$\cdot$day data obtained from the CDEX-10 experiment at the China Jinping Underground Laboratory, we derive new constraints on boosted DM within the NREFT framework. The NREFT coupling constant exclusion regions now penetrate the sub-GeV mass range, with optimal sensitivity achieved for operators $\mathcal{O}_{3}$, $\mathcal{O}_{6}$, $\mathcal{O}_{15}$ in the 0.4--0.6 GeV mass range.

hep-ph↗

arXiv2025

Rubber Wear: History, Mechanisms, and Perspectives

This paper presents a comprehensive review of wear mechanisms, with a primary focus on rubber wear under sliding conditions. Beginning with classical wear theories, including the Archard and Rabinowicz models, we analyze their applicability to both metals and elastomers and discuss extensions relevant to elastic contact and multiscale surface roughness. Various experimental studies on rubber, such as abrasion by sharp tools, erosion by particle impact, and wear during sliding on rough substrates, are reviewed and interpreted. The effects of environmental factors, such as oxygen and lubrication, are also discussed. In addition, we review a recently proposed wear model based on fatigue crack growth within asperity contact regions, which accounts for energy dissipation and multiscale interactions. This model explains the wide variability in the wear coefficient and predicts wear rates consistent with experimental observations across a broad range of conditions. It also explains the formation mechanism and provides the size distribution of rubber wear particles, from micrometer-scale up to severe cut-chip-chunk (CCC) wear. The results have implications for tire wear and the environmental impact of microscale wear debris (microplastics).

cond-mat.soft↗

arXiv2025

Rubber wear on concrete: dry and in-water conditions

Rubber wear results from the removal of small (micrometer-sized) rubber particles through crack propagation. In this study, we investigate the wear behavior of Styrene-Butadiene Rubber (SBR) and Natural Rubber (NR) sliding on two different concrete surfaces under dry and wet (in water) conditions. Experiments are conducted at low sliding speeds ($\approx 3 \ {\rm mm/s}$) to minimize frictional heating and hydrodynamic effects. For two SBR compounds, we observe significantly higher wear rates in water compared to the dry state, with enhancement factors of $1.5-2.5$ for a low-glass-transition-temperature SBR compound ($T_{\rm g} = -50^\circ {\rm C}$) and approximately $4$ for a higher-glass-transition compound ($T_{\rm g} = -7^\circ {\rm C}$). In contrast, the NR compound showed no wear in water at low nominal contact pressures ($\sigma_0 \approx 0.12$, $0.16$, and $0.25 \ {\rm MPa}$), while at higher pressures ($\sigma_0 \approx 0.36$ and $0.49 \ {\rm MPa}$), the wear rates in dry and in-water states are similar. The findings provide insights into the mechanisms of rubber wear under varying environmental and mechanical conditions, highlighting the influence of material properties, interfacial effects, and applied pressures on wear behavior.

cond-mat.soft↗

arXiv2024

Rubber wear: experiment and theory

We study the wear rate (mass loss per unit sliding distance) of a tire tread rubber compound sliding on concrete paver surfaces under dry and wet conditions, at different nominal contact pressures of $\sigma_0 = 0.12$, $0.29$, and $0.43 \ {\rm MPa}$, and sliding velocities ranging from $v= 1 \ {\rm \mu m/s}$ to $1 \ {\rm cm/s}$. We find that the wear rate is proportional to the normal force and remains independent of the sliding speed. Sliding in water and soapy water results in significantly lower wear rates compared to dry conditions. The experimental data are analyzed using a theory that predicts wear rates and wear particle size distributions consistent with the experimental observations.

cond-mat.soft↗

arXiv2024

On how to determine surface roughness power spectra

Analytical contact mechanics theories depend on surface roughness through the surface roughness power spectrum. In the present study, we evaluated the usability of various experimental methods for studying surface roughness. Our findings indicated that height data obtained from optical methods often lack accuracy and should not be utilized for calculating surface roughness power spectra. Conversely, engineering stylus instruments and atomic force microscopy (AFM) typically yield reliable results that are consistent across the overlapping roughness length scale region. For surfaces with isotropic roughness, the two-dimensional (2D) power spectrum can be derived from the one-dimensional (1D) power spectrum using several approaches, which we explored in this paper.

cond-mat.mtrl-sci↗

arXiv2024

Search for solar axions by Primakoff effect with the full dataset of the CDEX-1B Experiment

We present the first limit on $g_{Aγ}$ coupling constant using the Bragg-Primakoff conversion based on an exposure of 1107.5 kg days of data from the CDEX-1B experiment at the China Jinping Underground Laboratory. The data are consistent with the null signal hypothesis, and no excess signals are observed. Limits of the coupling $g_{Aγ}<2.08\times10^{-9}$ GeV$^{-1}$ (95\% C.L.) are derived for axions with mass up to 100 eV/$c^2$. Within the hadronic model of KSVZ, our results exclude axion mass $>5.3~\rm{eV}/c^2$ at 95\% C.L.

hep-ex↗

arXiv2024

Experimental Limits on Solar Reflected Dark Matter with a New Approach on Accelerated-Dark-Matter-Electron Analysis in Semiconductors

Recently a dark matter-electron (DM-electron) paradigm has drawn much attention. Models beyond the standard halo model describing DM accelerated by high energy celestial bodies are under intense examination as well. In this Letter, a velocity components analysis (VCA) method dedicated to swift analysis of accelerated DM-electron interactions via semiconductor detectors is proposed and the first HPGe detector-based accelerated DM-electron analysis is realized. Utilizing the method, the first germanium based constraint on sub-GeV solar reflected DM-electron interaction is presented with the 205.4 kg$\cdot$day dataset from the CDEX-10 experiment. In the heavy mediator scenario, our result excels in the mass range of 5$-$15 keV/$c^2$, achieving a 3 orders of magnitude improvement comparing with previous semiconductor experiments. In the light mediator scenario, the strongest laboratory constraint for DM lighter than 0.1 MeV/$c^2$ is presented. The result proves the feasibility and demonstrates the vast potential of the VCA technique in future accelerated DM-electron analyses with semiconductor detectors.

hep-ex↗