arXiv subjects

Oliver Sander

Publications and source records attributed to Oliver Sander.

At least 19 recordsLinked to original sources

arXiv2025

CryoDE: a Digital Cryogenic Detector Emulator for Microwave SQUID Multiplexed Systems

Simultaneous readout of large-scale cryogenic detector arrays relies on multiplexing schemes such as the FDM (Frequency-Division Multiplexing) with microwave SQUID multiplexers and highly customized readout electronics. In traditional detector systems, where mixed-signal ASICs are used in detector front-ends and typically provide a digital interface, HIL (Hardware-in-the-Loop) testing can be readily implemented by reusing the existing digital logic of the front-end for emulation purposes. Such straightforward emulation is not possible for FDM low-temperature detectors, where the sensor signal is encoded in a high-frequency microwave carrier via a two-stage modulation scheme depending on the cryogenic resonators and the SQUID response. To address this challenge, we present CryoDE, a digital cryogenic-detector emulator for microwave SQUID multiplexed detector systems. CryoDE generates the encoded detector signals, including realistic pulse responses, enabling full HIL testing of the room-temperature DAQ system without requiring the cryogenic hardware. This resource-efficient FPGA-based detector twin integrates seamlessly into existing DAQ systems and allows experiment-specific adjustment of detector-signal parameters. We describe the internal architecture and capabilities of CryoDE within our custom HIL framework and demonstrate its use in evaluating the performance of real-time signal processing firmware optimized for different microwave SQUID multiplexed cryogenic-detector experiments.

physics.ins-det↗

arXiv2025

Finite element discretizations of bending plates with prestrained microstructure

We investigate a finite element discretization of an elastic bending-plate model with an effective prestrain. The model has been obtained via homogenization and dimension reduction by B\"onlein at al. (2023). Its energy functional is the $\Gamma$-limit of a three-dimensional nonlinear microstructured elasticity functional. In the derived effective model, the microstructure is incorporated as a local corrector problem, a system of linear elliptic partial differential equations posed on a three-dimensional representative volume element. The discretization uses Discrete Kirchhoff Triangle elements for the macroscopic bending-plate problem on a mesh of scale $H$, and first-order Lagrange elements for the microscopic corrector problem on an axis-aligned mesh of scale $h$. We show that the discretized model $\Gamma$-converges to the continuous one as $(h,H)\to 0$,provided that there exists a microstructure mesh such that the elasticity tensor is Lipschitz continuous on each mesh element. This extends earlier results by Rumpf et al. (2024) to prestrained composites. Our argument does not require any rate of convergence for the microscopic discretization error. As a corollary, we also obtain convergence when $h \to 0$ and $H \to 0$ consecutively, and we prove that these limit processes commute.

math.NA↗

arXiv2025

SoCks - Simplifying Firmware and Software Integration for Heterogeneous SoCs

Modern heterogeneous System-on-Chip (SoC) devices integrate advanced components into a single package, offering powerful capabilities while also introducing significant complexity. To manage these sophisticated devices, firmware and software developers need powerful development tools. However, as these tools become increasingly complex, they often lack adequate support, resulting in a steep learning curve and challenging troubleshooting. To address this, this work introduces System-on-Chip blocks (SoCks), a flexible and expandable build framework that reduces complexity by partitioning the SoC image into high-level units called blocks. SoCks builds each firmware and software block in an encapsulated way, independently from other components of the image, thereby reducing dependencies to a minimum. While some information exchange between the blocks is unavoidable to ensure seamless runtime integration, this interaction is standardized via interfaces. A small number of dependencies and well-defined interfaces simplify the reuse of existing block implementations and facilitate seamless substitution between versions-for instance, when choosing root file systems for the embedded Linux operating system. Additionally, this approach facilitates the establishment of a decentralized and partially automated development flow through Continuous Integration and Continuous Delivery (CI/CD). Measurement results demonstrate that SoCks can build a complete SoC image up to three times faster than established tools.

cs.AR↗

arXiv2025

Improved limit on the effective electron neutrino mass with the ECHo-1k experiment

The effective electron neutrino mass can be determined by analyzing the endpoint region of the $^{163}$Ho electron capture spectrum, provided a measurement with high energy resolution and high statistics using calorimetric techniques. Here, the Electron Capture in $^{163}$Ho collaboration, ECHo, presents an analysis of the most precise $^{163}$Ho spectrum currently available, obtained with the ECHo-1k experiment and comprising about 200 million events. A very low background rate of $B=9.1(1.3)\times 10^{-6}$ /eV/pixel/day was achieved allowing for a reliable analysis of the endpoint region. The derived endpoint energy $Q = 2862(4)$ eV is in excellent agreement with the one independently determined via Penning-trap mass spectrometry of $Q=2863.2(6)$ eV [1]. The upper limit of the effective electron neutrino mass is improved by almost a factor 2 compared to the lowest current value [2], reaching $m_{\nu_\mathrm{e}} < 15 $ eV/c${^2}$ (90\% credible interval).

hep-ex↗

arXiv2025

Concepts for Composing Finite Element Function Space Bases

Finite Element discretizations of coupled multi-physics partial differential equation models require the handling of composed function spaces. In this paper we discuss software concepts and abstractions to handle the composition of function spaces, based on a representation of product spaces as trees of simpler bases. From this description, many different numberings of degrees of freedom by multi-indices can be derived in a natural way, allowing to adapt the function spaces to very different data layouts, so that it opens the possibility to directly use the finite element code with very different linear algebra codes, different data structures, and different algebraic solvers. A recurring example throughout the paper is the stationary Stokes equation with Taylor--Hood elements as these are naturally formulated as product spaces and highlight why different storage patterns are desirable. In the second half of the paper we discuss a particular realization of most of these concepts in the \dunemodule{dune-functions} module, as part of the DUNE ecosystem.

cs.MS↗

arXiv2025

The Distributed and Unified Numerics Environment (DUNE), Version 2.10

Version 2.10 of the Distributed and Unified Numerics Environment DUNE introduces a range of enhancements across its core and extension modules, with a continued emphasis on modern C++ integration and improved usability. This release extends support for C++20 features, particularly concepts, through comprehensive refinements in dune-common and dune-grid, enabling safer and more expressive generic programming paradigms. A notable advancement is the improved support for curved geometries, including new geometry implementations and a more flexible interface. Data structures have been modernized through native support for std::mdspan and std::mdarray, performance improvements in sparse matrices, and tools for visualization of matrix patterns. The build system has been restructured towards a modern CMake workflow, emphasizing target-based configuration and improved automation. Furthermore, new local finite elements have been introduced to broaden numerical capabilities. The release also brings updates across DUNE extensions, as well as improvements to infrastructure and module-level components.

cs.MS↗

arXiv2025

How to project onto SL($n$)

We consider the closest-point projection with respect to the Frobenius norm of a general real square matrix to the set SL($n$) of matrices with unit determinant. As it turns out, it is sufficient to consider diagonal matrices only. We investigate the structure of the problem both in Euclidean coordinates and in an $n$-dimensional generalization of the classical hyperbolic coordinates of the positive quadrant. Using symmetry arguments we show that the global minimizer is contained in a particular cone. Based on different views of the problem, we propose four different iterative algorithms, and we give convergence results for all of them. Numerical tests show that computing the projection costs essentially as much as a singular value decomposition. Finally, we give an explicit formula for the first derivative of the projection.

math.OC↗

arXiv2025

Quasiconvex relaxation of planar Biot-type energies and the role of determinant constraints

We derive the quasiconvex relaxation of the Biot-type energy density $\lVert\sqrt{\operatorname{D}\varphi^T \operatorname{D}\varphi}-I_2\rVert^2$ for planar mappings $\varphi\colon\mathbb{R}^2\to \mathbb{R}^2$ in two different scenarios. First, we consider the case $\operatorname{D}\varphi\in\textrm{GL}^+(2)$, in which the energy can be expressed as the squared Euclidean distance $\operatorname{dist}^2(\operatorname{D}\varphi,\textrm{SO}(2))$ to the special orthogonal group $\textrm{SO}(2)$. We then allow for planar mappings with arbitrary $\operatorname{D}\varphi\in\mathbb{R}^{2\times 2}$; in the context of solid mechanics, this lack of determinant constraints on the deformation gradient would allow for self-interpenetration of matter. We demonstrate that the two resulting relaxations do not coincide and compare the analytical findings to numerical results for different relaxation approaches, including a rank-one sequential lamination algorithm, trust-region FEM calculations of representative microstructures and physics-informed neural networks.

math.AP↗

arXiv2024

Cross-Chip Partial Reconfiguration for the Initialisation of Modular and Scalable Heterogeneous Systems

The almost unlimited possibilities to customize the logic in an FPGA are one of the main reasons for the versatility of these devices. Partial reconfiguration exploits this capability even further by allowing to replace logic in predefined FPGA regions at runtime. This is especially relevant in heterogeneous SoCs, combining FPGA fabric with conventional processors on a single die. Tight integration and supporting frameworks like the FPGA subsystem in Linux facilitate use, for example, to dynamically load custom hardware accelerators. Although this example is one of the most common use cases for partial reconfiguration, the possible applications go far beyond. We propose to use partial reconfiguration in combination with the AXI C2C cross-chip bus to extend the resources of heterogeneous MPSoC and RFSoC devices by connecting peripheral FPGAs. With AXI C2C it is easily possible to link the programmable logic of the individual devices, but partial reconfiguration on peripheral FPGAs utilising the same channel is not officially supported. By using an AXI ICAP controller in combination with custom Linux drivers, we show that it is possible to enable the PS of the heterogeneous SoC to perform partial reconfiguration on peripheral FPGAs, and thus to seamlessly access and manage the entire multi-device system. As a result, software and FPGA firmware updates can be applied to the entire system at runtime, and peripheral FPGAs can be added and removed during operation.

physics.ins-det↗

arXiv2024

Two-level system hyperpolarization using a quantum Szilard engine

The innate complexity of solid state physics exposes superconducting quantum circuits to interactions with uncontrolled degrees of freedom degrading their coherence. By using a simple stabilization sequence we show that a superconducting fluxonium qubit is coupled to a two-level system (TLS) environment of unknown origin, with a relatively long energy relaxation time exceeding $50\,\text{ms}$. Implementing a quantum Szilard engine with an active feedback control loop allows us to decide whether the qubit heats or cools its TLS environment. The TLSs can be cooled down resulting in a four times lower qubit population, or they can be heated to manifest themselves as a negative temperature environment corresponding to a qubit population of $\sim 80\,\%$. We show that the TLSs and the qubit are each other's dominant loss mechanism and that the qubit relaxation is independent of the TLS populations. Understanding and mitigating TLS environments is therefore not only crucial to improve qubit lifetimes but also to avoid non-Markovian qubit dynamics.

quant-ph↗

arXiv2023

High-order integration on regular triangulated manifolds reaches super-algebraic approximation rates through cubical re-parameterizations

We present a novel methodology for deriving high-order volume elements (HOVE) designed for the integration of scalar functions over regular embedded manifolds. For constructing HOVE we introduce square-squeezing --a homeomorphic multilinear hypercube-simplex transformation reparametrizing an initial flat triangulation of the manifold to a cubical mesh. By employing square-squeezing, we approximate the integrand and the volume element for each hypercube domain of the reparameterized mesh through interpolation in Chebyshev-Lobatto grids. This strategy circumvents the Runge phenomenon, replacing the initial integral with a closed-form expression that can be precisely computed by high-order quadratures. We prove novel bounds of the integration error in terms of the $r^\text{th}$-order total variation of the integrand and the surface parameterization, predicting high algebraic approximation rates that scale solely with the interpolation degree and not, as is common, with the average simplex size. For smooth integrals whose total variation is constantly bounded with increasing $r$, the estimates prove the integration error to decrease even exponentially, while mesh refinements are limited to achieve algebraic rates. The resulting approximation power is demonstrated in several numerical experiments, particularly showcasing $p$-refinements to overcome the limitations of $h$-refinements for highly varying smooth integrals.

math.NA↗

arXiv2023

A geometrically nonlinear Cosserat shell model for orientable and non-orientable surfaces: Discretization with geometric finite elements

We investigate discretizations of a geometrically nonlinear elastic Cosserat shell with nonplanar reference configuration originally introduced by Bîrsan, Ghiba, Martin, and Neff in 2019. The shell model includes curvature terms up to order 5 in the shell thickness, which are crucial to reliably simulate high-curvature deformations such as near-folds or creases. The original model is generalized to shells that are not homeomorphic to a subset of $\mathbb{R}^2$. For this, we replace the originally planar parameter domain by an abstract two-dimensional manifold, and verify that the hyperelastic shell energy and three-dimensional reconstruction are invariant under changes of the local coordinate systems. This general approach allows to determine the elastic response for even non-orientable surfaces like the Möbius strip and the Klein bottle. We discretize the model with a geometric finite element method and, using that geometric finite elements are $H^1$-conforming, prove that the discrete shell model has a solution. Numerical tests then show the general performance and versatility of the model and discretization method.

math.NA↗

arXiv2023

Simultaneous MMC readout using a tailored μMUX based readout system

Magnetic microcalorimeters (MMCs) are cryogenic, energy-dispersive single-particle detectors providing excellent energy resolution, intrinsically fast signal rise time, quantum efficiency close to 100\%, large dynamic range as well as almost ideal linear response. One of the remaining challenges to be overcome to ultimately allow for the utilization of large-scale MMC based detector arrays with thousands to millions of individual pixels is the realization of a SQUID based multiplexing technique particularly tailored for MMC readout. Within this context, we report on the first truly multiplexed readout of an MMC based detector array using a frequency-division multiplexing approach realized by a custom microwave SQUID multiplexer based readout system.

physics.ins-det↗

arXiv2023

DTS-100G -- A versatile heterogeneous MPSoC board for cryogenic sensor readout

Heterogeneous devices such as the Multi-Processor System-on-Chip (MPSoC) from Xilinx are extremely valuable in custom instrumentation systems. This contribution presents the joint development of a heterogeneous MPSoC board called DTS-100G by DESY and KIT. The board is built around a Xilinx Zynq Ultrascale+ chip offering all available high-speed transceivers using QSFP28, 28 Gbps FireFly, FMC, and FMC+ interfaces. The board is not designed for a particular application, but can be used as a generic DAQ platform for a variety of physics experiments. The DTS-100G board was successfully developed, built, and commissioned. ECHo-100k is the first experiment which will employ the board. This contribution shows the system architecture and explains how the DTS-100G board is a crucial component in the DAQ chain.

physics.ins-det↗

arXiv2023

Split Boot -- True Network-Based Booting on Heterogeneous MPSoCs

In the context of the High-Luminosity (HL) upgrade of the LHC, many custom ATCA electronics boards are being designed containing heterogeneous System-on-Chip (SoC) devices, more specifically the Xilinx Zynq UltraScale+ (ZUS+) family. While the application varies greatly, these devices are regularly used for performing board management tasks, making them a fundamental element in the correct operation of the board. The large number of hundreds of SoC devices creates significant challenges in their firmware deployment, maintenance, and accessibility. Even though U-Boot on ZUS+ devices supports network boot through the Preboot Execution Environment (PXE), the standard ZUS+ boot process contains application-specific information at earlier boot steps, particularly within the First Stage Bootloader (FSBL). This prevents the initialization of several devices from a universal image. Inspired by the PXE boot process on desktop PCs, this paper describes split boot, a novel boot method tailored to the specific needs of the ZUS+. All application-specific configuration is moved to a network storage device and automatically fetched during the boot process. We considered the entire process, from firmware and software development to binary distribution in a large-scale system. The developed method nicely integrates with the standard Xilinx development toolset workflow.

physics.ins-det↗

arXiv2022

Benchmarking Numerical Algorithms for Harmonic Maps into the Sphere

We numerically benchmark methods for computing harmonic maps into the unit sphere, with particular focus on harmonic maps with singularities. For the discretization we compare two different approaches, both based on Lagrange finite elements. While the first method enforces the unit-length constraint only at the Lagrange nodes, the other one adds a pointwise projection to fulfill the constraint everywhere. For the solution of the resulting algebraic problems we compare a nonconforming gradient flow with a Riemannian trust-region method. Both are energy-decreasing and can be shown to converge globally to stationary points of the discretized Dirichlet energy. We observe that while the nonconforming and the conforming discretizations both show similar behavior for smooth problems, the nonconforming discretization handles singularities better. On the solver side, the second-order trust-region method converges after few steps, whereas the number of gradient-flow steps increases proportionally to the inverse grid element diameter.

math.NA↗

arXiv2022

Representative volume element approximations in elastoplastic spring networks

We study the large-scale behavior of a small-strain lattice model for a network composed of elastoplastic springs with random material properties. We formulate the model as an evolutionary rate independent system (ERIS). In an earlier work we derived a homogenized continuum model, which has the form of linearized elastoplasticity, as evolutionary $Γ$-limit as the lattice parameter tends to zero. In the present paper we introduce a periodic representative volume element approximation (RVE) for the homogenized system. As a main result we prove convergence of the RVE approximation as the size of the RVE tends to infinity. We also show that the hysteretic stress-strain relation of the effective system can be described with help of a generalized Prandt-Ishlinskii operator, and we prove convergence of a periodic RVE approximation for that operator. We combine the RVE approximation with a numerical scheme for rate-independent systems and obtain a computational scheme that we use to numerically investigate the homogenized system in the specific case when the original network is given by a two-dimensional lattice model. We simulate the response of the system to cyclic and uniaxial, monotonic loading, and numerically investigate the convergence rate of the periodic RVE approximation. In particular, our simulations show that the RVE error decays with the same rate as the RVE error in the static case of linear elasticity.

math.NA↗

arXiv2022

A homogenized bending theory for prestrained plates

The presence of prestrain can have a tremendous effect on the mechanical behavior of slender structures. Prestrained elastic plates show spontaneous bending in equilibrium -- a property that makes such objects relevant for the fabrication of active and functional materials. In this paper we study microheterogeneous, prestrained plates that feature nonflat equilibrium shapes. Our goal is to understand the relation between the properties of the prestrained microstructure and the global shape of the plate in mechanical equilibrium. To this end, we consider a three-dimensional, nonlinear elasticity model that describes a periodic material that occupies a domain with small thickness. We consider a spatially periodic prestrain described in the form of a multiplicative decomposition of the deformation gradient. By simultaneous homogenization and dimension reduction, we rigorously derive an effective plate model as a Γ-limit for vanishing thickness and period. That limit has the form of a nonlinear bending energy with an emergent spontaneous curvature term. The homogenized properties of the bending model (bending stiffness and spontaneous curvature) are characterized by corrector problems. For a model composite -- a prestrained laminate composed of isotropic materials -- we investigate the dependence of the homogenized properties on the parameters of the model composite. Secondly, we investigate the relation between the parameters of the model composite and the set of shapes with minimal bending energy. Our study reveals a rather complex dependence of these shapes on the composite parameters.

math.AP↗