arXiv subjects

Mohsen Moradi

Publications and source records attributed to Mohsen Moradi.

At least 19 recordsLinked to original sources

arXiv2026

Hardware-Efficient Reinforcement-Learned Scheduling for Quantum LDPC Decoders

Quantum low-density parity-check (QLDPC) codes are promising for fault-tolerant quantum computing, but their decoding algorithms present significant hardware implementation challenges. Reinforcement-learned sequential belief propagation (RL-S) improves the error-correction performance of conventional belief propagation (BP) through adaptive variable-node scheduling. However, its heap-based priority management introduces substantial hardware overhead. This paper presents hardware implementations of BP, RL-S, and bucket-based reinforcement-learned BP (BRL-S) for the [[288,12,18]] bivariate bicycle QLDPC code. The BRL-S architectures employ quantized priorities and first-in, first-out (FIFO) buckets to simplify scheduling. Three configurations with two, four, and eight priority levels are evaluated. FPGA synthesis results demonstrate that BRL-S reduces lookup-table utilization by approximately 68--72% compared with RL-S. ASIC synthesis further shows reductions of 63--67% in area and 64--69% in estimated power consumption. These results demonstrate that bucket-based scheduling substantially improves the hardware efficiency of reinforcement-learned QLDPC decoders.

cs.IT↗

arXiv2026

PMR-Aided Shifted-Pruning SCL-Flip Decoding for CRC-Aided Polar Codes

We propose a posterior-mass rescue (PMR)-aided shifted-pruning SCL-flip decoder for CRC-aided polar codes. After CRC-aided SCL (CA-SCL) and differential-metric shifted-pruning recovery fail to find a CRC-valid candidate, PMR locally continues discarded prefixes stored during the initial CA-SCL pass, ranked by estimated posterior mass, without increasing the shifted-pruning retry budget. Simulation results for a (128, 64) code with the Reed-Muller (RM) rate profile and a (256, 128) code with the polarization-weight (PW) rate profile, both using an 11-bit CRC, show lower observed FER than SCLF-Diff (T = 15) and the considered literature baselines under the evaluated recovery budgets, with observed FER close to that of SCLF-Diff (T = 20). At the reported moderate and high SNRs, the average reconstruction-aware path-step count is within a few percent of that of SCLF-Diff (T = 20), while at 2.0 dB it is 9.4% and 4.3% higher for the two codes, respectively. The proposed decoder also has a larger worst-case path-step bound.

cs.IT↗

arXiv2026

Low-Latency Belief-Propagation Decoding of Quantum LDPC Codes with Reinforcement-Learned Scheduling

Belief propagation (BP) is attractive for quantum low-density parity-check (QLDPC) decoding because of its low complexity and low latency, but short cycles and degeneracy can limit its error-correction performance. Reinforcement-learned sequential scheduling (RL-S) substantially improves this performance by adapting the variable node (VN) update order, although Q-table storage and heap-based selection introduce additional overhead. We propose bucket RL-S (B-RL-S), which quantizes learned Q-values into integer priorities and schedules VN updates using dynamically maintained first-in, first-out buckets. Without retraining or changing the BP message updates, B-RL-S reduces policy storage and refreshes only priorities affected by local residual syndrome changes. A fixed number of priority levels enables constant-time VN selection and queue relocation. For the $[[288,12,18]]$ bivariate bicycle code over the depolarizing channel at $p=0.05$, B-RL-S with eight priority levels achieves approximately one fifth the block error rate (BLER) of flooding BP followed by order-10 ordered-statistics decoding. The respective caps are $1000$ sequential iterations for B-RL-S and $1000$ flooding iterations for the BP stage of the reference decoder. These results highlight strong error correction with inexpensive scheduling and no additional post-processing stage.

cs.IT↗

arXiv2026

Learned Parallel Bit-Flipping Sequential Belief Propagation Decoding of Quantum LDPC Codes

Quantum low-density parity-check (QLDPC) codes are promising candidates for low-overhead fault-tolerant quantum computation, but their practical use requires fast, low-complexity, and reliable decoders. Belief propagation (BP) is attractive because of its local message-passing structure, yet standard flooding BP often suffers from convergence failures on QLDPC codes due to short cycles, degeneracy, and symmetric decoding trajectories. Learned sequential BP improves convergence by using a reinforcement-learning policy to choose variable-node update orders, but a single learned trajectory can still be sensitive to unfavorable local Pauli decisions. We propose a learned parallel bit-flipping sequential BP decoder with a new quaternary score combining syndrome gain, a quantized Pauli log-likelihood penalty, and Q-table lookahead at hypothetical post-flip states. Our decoder first runs learned sequential BP for a fixed number of iterations. If the syndrome is not satisfied, it constructs quaternary bit-flipping candidates, each corresponding to changing the current Pauli decision of one qubit. The selected candidates initialize independent learned sequential BP continuations from the same decoder state. Since these continuations are independent, they can be executed in parallel, so testing several candidates mainly increases parallel hardware resources rather than sequential decoding latency. Simulations on representative QLDPC codes over the depolarizing channel show that the proposed decoder improves the reliability of learned sequential BP while having a parallel low-latency structure.

quant-ph↗

arXiv2026

Conflict-Free Color-Clustered Sequential Belief-Propagation Decoding of Quantum LDPC Codes via Reinforcement Learning

Belief-propagation (BP) decoding for quantum low-density parity-check (QLDPC) codes is attractive due to its low complexity and low latency, but it is often limited by short cycles, degeneracy, and convergence failures. Reinforcement-learning-based sequential BP decoding (RL-S) improves BP by learning a syndrome-dependent variable-node (VN) update order, but its VN-by-VN schedule has limited within-iteration parallelism. In this paper, we propose a conflict-free color-clustered extension of RL-S. We construct a VN conflict graph in which two VNs are adjacent if they share an X-type or Z-type check, and color this graph so that same-color VNs have disjoint check neighborhoods. This also prevents VNs from the same Tanner 4- or 6-cycle from being updated simultaneously. During decoding, the trained VN-level Q-table selects a seed VN, and all remaining VNs with the same color are updated in parallel using the same pre-batch messages. For the [[288,12,18]] bivariate-bicycle code over the depolarizing channel, our proposed decoder achieves block-error-rate performance close to VN-level RL-S while reducing the scheduling decisions from 288 VNs to 11 color classes per BP iteration.

cs.IT↗

arXiv2026

Lifted-Product QLDPC Codes in the Polynomial Domain

This paper presents a finite-length polynomial-domain formulation of lifted-product quantum low-density parity-check (QLDPC) codes. We formulate the code construction over the quotient ring F 2[D]/(D L + 1), where polynomial base matrices are lifted entrywise to binary circulant blocks. This representation gives a compact algebraic description of the lifted-product parity-check matrices and allows CSS orthogonality to be analyzed before binary expansion. We show that the standard circulant lifting map is compatible with polynomial conjugation, which implies that the resulting binary matrices satisfy the CSS commutation constraint. The construction is illustrated with a constraint length 7, rate 1/2 NASA convolutional code example, and numerical examples are provided from a 3 x 4 polynomial parity-check matrix. The finite-length performance of selected constructed codes is then evaluated over the depolarizing channel using various benchmark decoders. The resulting framework gives a structured method to construct finite-length lifted-product QLDPC codes from small polynomial base matrices.

cs.IT↗

arXiv2026

High-Performance Reinforcement-Learned BP Decoding of Quantum LDPC Codes

Belief-propagation (BP) decoding is attractive for quantum low-density parity-check (QLDPC) codes because it uses local message passing on sparse Tanner graphs. However, conventional flooding BP often stalls due to stabilizer degeneracy and short cycles. Reinforcement-learning-based sequential variable-node scheduling (RL-S), which learns the update order offline, has shown that adaptive scheduling can improve BP convergence. In this paper, we extend this idea with a second-order local update decoder, RL-S2LU. The proposed decoder preserves BP locality and low complexity, while numerical results show significant error-correction gains over conventional BP and the considered BP-OSD-10 baseline.

cs.IT↗

arXiv2026

Learning to Decode Quantum LDPC Codes via Cluster-Based Sequential Belief Propagation

Belief-propagation (BP) decoding for quantum low-density parity-check (QLDPC) codes is attractive due to its low complexity, but its performance is often limited by short cycles, degeneracy, and convergence failures. Recently, reinforcement-learning-based sequential variable-node (VN) scheduling (RL-S) was shown to improve BP decoding by learning state-dependent update orders. However, the VN-by-VN nature of that approach offers limited within-iteration parallelism, since only one VN is updated at a time. In this paper, we propose a cluster-based extension of RL-S for QLDPC codes. The VNs are partitioned into fixed clusters, and at each scheduling step the RL agent selects one cluster to update, after which all VNs in that cluster are updated in parallel using the same pre-update incoming messages. To keep the tabular state space practical for large cluster sizes, we introduce a permutation-invariant cluster state based on a normalized histogram of local mismatch weights, followed by quantization. This representation makes the number of cluster states depend on the quantization resolution rather than the cluster size. We also develop the corresponding cluster-level Markov decision process, reward function, and Q-learning update. Numerical results on representative QLDPC codes show that the proposed clustered learned scheduling preserves most of the error-rate benefit of VN-level learned sequential scheduling while substantially reducing the number of scheduling decisions per BP iteration, thereby providing an attractive latency-parallelism tradeoff.

cs.IT↗

arXiv2026

Learning-Based List Sequential Belief Propagation Decoding of Quantum LDPC Codes

Quantum low-density parity-check (QLDPC) codes are strong candidates for fault-tolerant quantum computation, but efficient decoding remains a major challenge due to short cycles, degeneracy, and the poor convergence of standard belief-propagation (BP) decoders. We propose a reinforcement learning-based list sequential (RL-LS) BP decoder for QLDPC codes by extending the reinforcement-learning-based sequential variable-node scheduling (RL-S) framework with list-based search. At each step, the learned policy selects the next variable node to update; the decoder then retains the ordinary RL-S trajectory while also exploring a competing branch obtained by softly biasing the post-update LLR pair toward the second-most likely Pauli symbol, recomputing the incident local BP messages, and setting the visited variable node to that second-best symbol. Candidate trajectories are ranked and pruned using our proposed cumulative path metric. The resulting decoder extends the learned decoder by combining the improved convergence of learned sequential scheduling with list exploration. Numerical results on representative QLDPC benchmark codes over the depolarizing channel show that our proposed method improves the decoding performance of the underlying decoder and compares favorably with existing BP-based decoding methods.

cs.IT↗

arXiv2026

Efficient Low-Memory Fast Stack Decoding with Variance Polarization for PAC Codes

Polarization-adjusted convolutional (PAC) codes have recently emerged as a promising class of error-correcting codes, achieving near-capacity performance particularly in the short block-length regime. In this paper, we propose an enhanced stack decoding algorithm for PAC codes that significantly improves parallelization by exploiting specialized bit nodes, such as rate-0 and rate-1 nodes. For a rate-1 node with $N_0$ leaf nodes in its corresponding subtree, conventional stack decoding must either explore all $2^{N_0}$ paths, or, same as in fast list decoding, restrict attention to a constant number of candidate paths. In contrast, our approach introduces a pruning technique that removes candidate paths with small path metrics while ensuring that the probability of pruning the correct path decays exponentially with the threshold. Furthermore, we propose a novel approximation method for estimating variance polarization under the binary-input additive white Gaussian noise (BI-AWGN) channel. Leveraging these approximations, we develop an efficient stack-pruning strategy that selectively preserves decoding paths whose bit-metric values align with their expected means. This targeted pruning substantially reduces the number of active paths in the stack, thereby decreasing both decoding latency and computational complexity. Numerical results demonstrate that for a PAC$(128,64)$ code, our method achieves up to a 70\% reduction in the average number of paths without degrading error-correction performance.

cs.IT↗

arXiv2026

Learning to Decode Quantum LDPC Codes Via Belief Propagation

Belief-propagation (BP) decoding for quantum low-density parity-check (QLDPC) codes is appealing due to its low complexity, yet it often exhibits convergence issues due to quantum degeneracy and short cycles that exist in the Tanner graph. To overcome this challenge, this paper proposes a reinforcement-learning (RL) approach that learns (offline) how to decode QLDPC codes based on sequential decoding trajectories. The decoding is formulated as a Markov decision process with a local, syndrome-driven state representation of the underlying RL agent. To enable fast inference, critical for practical implementation, we incrementally update our RL-based QLDPC decoder using second-order neighborhoods that avoid global rescans. Simulation results on representative QLDPC codes demonstrate the superiority of the proposed RL-based QLDPC decoders in terms of performance and convergence speed when compared to flooding and random sequential schedules, while achieving performance competitive with state-of-the-art BP-based decoders at comparable complexity.

cs.IT↗

arXiv2026

Sequential BP-based Decoding of QLDPC Codes

Quantum low-density parity-check (QLDPC) codes are a leading approach to quantum error correction, yet conventional belief propagation (BP) decoders often perform poorly, primarily due to non-convergence exacerbated by stabilizer constraints, which induce short cycles and degeneracy. We propose two scheduling variants, sequential check node scheduling (SCNS) and sequential variable node scheduling (SVNS), that improve BP's error-correction ability by processing check nodes (CNs) or variable nodes (VNs), respectively, in a fixed order, stabilizing message updates and reducing stalls. We also employ this technique to an improved BP-variant called BP guided decimation (BPGD), where symbols are progressively fixed during decoding iterations. Here, we demonstrate that the sequential BPGD (SBPGD) decoder can further improve the convergence properties and performance of the decoder. On standard QLDPC benchmarks under a Pauli-X noise model, our sequential schedules are shown to lower the block error rate relative to conventional BP, and SBPGD outperforms BPGD while using significantly fewer decimation rounds, translating to lower computational cost. These results demonstrate that changing the update schedule, without altering the code, can improve both the reliability and efficiency of BP-based decoding for QLDPC codes. For the [[1922,50,16]] C2 hypergraph-product code with independent X errors, SVNS-BP surpasses BP-OSD-0 in error correction at roughly the same complexity as standard BP.

cs.IT↗

arXiv2025

Layered Normalized Min-Sum Decoding with Bit Flipping for FDPC Codes

Fair-density parity-check (FDPC) codes have been recently introduced demonstrating improved performance compared to low-density parity-check (LDPC) codes standardized in 5G systems particularly in high-rate regimes. In this paper, we introduce a layered normalized min-sum (LNMS) message-passing decoding algorithm for the FDPC codes. We also introduce a syndrome-guided bit flipping (SGBF) method to enhance the error-correction performance of our proposed decoder. The LNMS decoder leverages conflict graph coloring for efficient layered scheduling, enabling faster convergence by grouping non-conflicting check nodes and updating variable nodes immediately after each layer. In the event of decoding failure, the SGBF method is activated, utilizing a novel reliability metric that combines log-likelihood ratio (LLR) magnitudes and syndrome-derived error counts to identify the least reliable bits. A set of candidate sequences is then generated by performing single-bit flips at these positions, with each candidate re-decoded via LNMS. The optimal candidate is selected based on the minimum syndrome weight. Extensive simulation results demonstrate the superiority of the proposed decoder. Numerical simulations on FDPC$(256,192)$ code with a bit-flipping set size of $T = 128$ and a maximum of $5$ iterations demonstrate that the proposed decoder achieves approximately a $0.5\,\mathrm{dB}$ coding gain over standalone LNMS decoding at a frame error rate (FER) of $10^{-3}$, while providing coding gains of $0.75-1.5\,\mathrm{dB}$ over other state-of-the-art codes including polar codes and 5G-LDPC codes at the same length and rate and also under belief propagation decoding.

cs.IT↗

arXiv2025

A New Metric Function for SC-based Polar Decoders: Polarization, Pruning, and Fast Decoders

In this paper, we propose a method to obtain the optimal metric function at each depth of the polarization tree through a process we call polarization of the metric function. This polarization process generates an optimal metric at intermediate levels of the polarization tree, which can be applied in fast successive-cancellation-based (FSC) and SC list-based (FSCL) decoders -- decoders that partially explore the binary tree representation. We prove that at each step of the polarization tree, the expected value of the metric function random variable is the mutual information of the corresponding channel, while its variance equals the varentropy of the channel -- two parameters that are particularly relevant in finite block-length regimes. Additionally, we show that after polarization, the variances of the bit metrics approach zero for binary-input discrete memoryless channels (BI-DMCs). Moreover, we provide an estimate for calculating the variance of the binary-input additive white Gaussian noise (BI-AWGN) channel. We introduce a list-pruning strategy for FSCL decoding that retains only the paths whose metric values are close to the average. As a result, our method significantly reduces the number of required sorting operations in FSCL-based decoding algorithms. We also derive an upper bound, as a function of the polarized channel varentropy, on the probability that the distance between a bit-metric random variable and the bit-channel mutual information exceeds a given threshold. Leveraging this result, we further propose a varentropy-based list-pruning strategy for the SCL (VPSCL) decoding algorithm that adapts to the varentropy of the corresponding bit-channel. Our proposed pruning strategy also benefits stack decoding (VPStack) by discarding partial paths and avoiding unnecessary extensions.

cs.IT↗

arXiv2025

PAC codes with Bounded-Complexity Sequential Decoding: Pareto Distribution and Code Design

Recently, a novel variation of polar codes known as polarization-adjusted convolutional (PAC) codes has been introduced by Arıkan. These codes significantly outperform conventional polar and convolutional codes, particularly for short codeword lengths, and are shown to operate very close to the optimal bounds. It has also been shown that if the rate profile of PAC codes does not adhere to certain polarized cutoff rate constraints, the computation complexity for their sequential decoding grows exponentially. In this paper, we address the converse problem, demonstrating that if the rate profile of a PAC code follows the polarized cutoff rate constraints, the required computations for its sequential decoding can be bounded with a distribution that follows a Pareto distribution. This serves as a guideline for the rate-profile design of PAC codes. For a high-rate PAC\,$(1024,899)$ code, simulation results show that the PAC code with Fano decoder, when constructed based on the polarized cutoff rate constraints, achieves a coding gain of more than $0.75$ dB at a frame error rate (FER) of $10^{-5}$ compared to the state-of-the-art 5G polar and LDPC codes.

cs.IT↗

arXiv2025

Bounds and New Constructions for Girth-Constrained Regular Bipartite Graphs

In this paper, we explore the design and analysis of regular bipartite graphs motivated by their application in low-density parity-check (LDPC) codes specifically with constrained girth and in the high-rate regime. We focus on the relation between the girth of the graph, and the size of the sets of variable and check nodes. We derive bounds on the size of the vertices in regular bipartite graphs, showing how the required number of check nodes grows with respect to the number of variable nodes as girth grows large. Furthermore, we present two constructions for bipartite graphs with girth $\mathcal{G} = 8$; one based on a greedy construction of $(w_c, w_r)$-regular graphs, and another based on semi-regular graphs which have uniform column weight distribution with a sublinear number of check nodes. The second construction leverages sequences of integers without any length-$3$ arithmetic progression and is asymptotically optimal while maintaining a girth of $8$. Also, both constructions can offer sparse parity-check matrices for high-rate codes with medium-to-large block lengths. Our results solely focus on the graph-theoretic problem but can potentially contribute to the ongoing effort to design LDPC codes with high girth and minimum distance, specifically in high code rates.

cs.IT↗

arXiv2025

On the High-Rate FDPC Codes: Construction, Encoding, and a Generalization

Recently introduced Fair-Density Parity-Check (FDPC) codes, targeting high-rate applications, offer superior error-correction performance (ECP) compared to 5G Low-Density Parity-Check (LDPC) codes, given the same number of message-passing decoding iterations. In this paper, we present a novel construction method for FDPC codes, introduce a generalization of these codes, and propose a low-complexity encoding algorithm. Numerical results demonstrate the fast convergence of the message-passing decoder for FDPC codes.

cs.IT↗

arXiv2024

PAC Code Rate-Profile Design Using Search-Constrained Optimization Algorithms

In this paper, we introduce a novel rate-profile design based on search-constrained optimization techniques to assess the performance of polarization-adjusted convolutional (PAC) codes under Fano (sequential) decoding. The results demonstrate that the resulting PAC code offers much reduced computational complexity compared to a construction based on a conventional genetic algorithm without a performance loss in error-correction performance. As the fitness function of our algorithm, we propose an adaptive successive cancellation list decoding algorithm to determine the weight distribution of the rate profiles. The simulation results indicate that, for a PAC(256, 128) code, only 8% of the population requires that their fitness function be evaluated with a large list size. This represents an improvement of almost 92% over a conventional evolutionary algorithm. For a PAC(64, 32) code, this improvement is about 99%. We also plotted the performance of the high-rate PAC(128, 105) and PAC(64, 51) codes, and the results show that they exhibit superior performance compared to other algorithms.

cs.IT↗