arXiv subjects

Mark Oxborrow

Publications and source records attributed to Mark Oxborrow.

At least 19 recordsLinked to original sources

arXiv2026

Host-guest Crystal Engineering Tailors the Room Temperature Spin Dynamics in Molecular Quantum Devices

Molecular materials that enable coherent control over an electron's spin state at room temperature are promising candidates for quantum technologies, including quantum sensors and ultra-low noise microwave amplifiers, known as masers. Host-guest molecular crystals enable independent control of spin-active guests and their local environments to enhance molecular spin properties and so improve device performance. Using electron paramagnetic resonance and optically-detected magnetic resonance, we demonstrate the ability to tune triplet population, depopulation, and spin-lattice relaxation by modulating host-dependent lattice rigidity and vibrational coupling to significantly reduce the operating requirements for building useful masers. Importantly, the most rigid host, picene, reveals the ability to slow spin-lattice relaxation without lengthening triplet lifetime, though at the cost of strain-induced line width broadening and reduced triplet spin polarisation. We also find that deuteration reduces the triplet resonance line width and vibrationally-mediated triplet depopulation. Consequently, we find that perdeuterated pentacene in perdeuterated p-terphenyl is the most viable candidate for building a continuous wave maser. This work demonstrates host-guest engineering as an important and practical method for tuning the spin-dependent performance of room-temperature molecular quantum technologies.

quant-ph↗

arXiv2026

Heterogeneous Optically-Detected Spin-Acoustic Resonance in Solid-State Molecular Thin-film

We report an implementation of spin-acoustic resonance in pentacene thin films integrated on a high-quality-factor (high-Q) surface acoustic wave (SAW) resonator on a lithium niobate substrate. Heterogeneous optically detected spin-acoustic resonance (HODSAR) is an optically detected spin-resonance measurement in which the resonant drive is delivered mechanically by a surface acoustic wave (SAW). By leveraging the photo-excited triplet state of pentacene at room temperature, we demonstrate coherent spin manipulation via acoustic driving under zero externally applied magnetic field. The heterogeneously integrated device, referred to as HODSAR, utilizes spin-phonon coupling to achieve mechanically driven, zero-field spin resonance, opening avenues for room-temperature mechanically addressable spin control and device integration. We show that the high-Q multimode response of the SAW resonator enables spectrally selective acoustic addressing of triplet transitions near 105 MHz. Coherent control is evidenced by Rabi oscillations, with a Rabi frequency that increases linearly with the square root of the applied RF input power over the measured drive range, consistent with driven two-level dynamics under acoustic excitation. These results establish spin-acoustic resonance in a heterogeneously integrated molecular thin-film platform and provide a quantitative basis for benchmarking mechanically mediated spin control.

quant-ph↗

arXiv2026

Scaleable LED-pumped Room-temperature Maser using a Multi-blade Optical Injector

Though the performance of room-temperature masers has improved over the last decade, relatively little attention has been paid to the optics used to pump the maser's gain medium. In this work, we investigate a novel multi-blade optical ``injector'' that permits more effective and more scaleable pumping. The reported work encompasses an interdisciplinary mix of conceptualization, simulation, crystal growth, fabrication, and microwave engineering. Our gain medium is pentacene dissolved as a solid solution with para-terphenyl (Pc:PTP) molecular crystal. We accurately determine this pentacene's molecular absorption cross-section as a function of wavelength. Ray-tracing is then used to assess how different designs of waveguide inject light into the Pc:PTP crystal. A multi-blade injector made of high-refractive-index glass (namely Ohara S-TIH6) is predicted to pump it more completely and uniformly than previous designs. Upon hand-fabricating such an injector and Bridgman-growing a crystal of 0.1% Pc:PTP over it, an experimental maser oscillator using this combined injector-crystal assembly is demonstrated. The performance and scaleability of multiblade injection vis-a-vis alternative strategies is analyzed.

physics.optics↗

arXiv2025

Single-LED-pumped, room-temperature, solid-state maser

Through their ability to achieve cryogenic levels of noise performance while operating at room temperature, optically-pumped, solid-state (OPSS) masers show great promise as quantum sensors, oscillators, and amplifiers. We here demonstrate maser oscillation in a microwave cavity containing a crystal of pentacene-doped para-terphenyl (ptc:ptp) pumped by a single, chip-scale LED. Here, unlike previous work, the size of the pump source does not dominate the size of the maser system as a whole. This miniaturization is achieved through invasive optical pumping in the form of a waveguide, the tip of which is embedded into the maser crystal. Using experimental measurements combined with microwave and optical simulations, we find that our approach offers at least a factor-of-2 enhancement in cooperativity over end-on optical excitation. We use our simulations to define a figure of merit for maser pumping efficiency, and conclude that there remains significant headroom to improve the performance of ptc:ptp masers through improved optical design.

quant-ph↗

arXiv2025

Watt-level coherent microwave emission from dissipation engineered solid-state quantum batteries

Recently proposed metastability-induced quantum batteries have shown particular promise for coherent microwave generation. However, achieving high-power coherent microwave generation in quantum batteries remains fundamentally challenging due to quantum correlations, aging, and self-discharging processes. For the cavity-quantum-electrodynamics (CQED)-based quantum batteries, a further trade-off arises between strong spin-photon coupling for energy storage and sufficient output coupling for power delivery. To overcome these constraints, we introduce dissipation engineering as a dynamic control strategy that temporally separates energy storage and release. By suppressing emission during charging and rapidly enhancing the output coupling during discharging, we realize nanosecond microwave bursts with watt-level peak power. By optimizing three dissipation schemes, we improve work extraction efficiency of the quantum battery by over two orders of magnitude and achieve high power compression factors outperforming the state-of-the-art techniques, establishing dissipation engineering as a pathway toward room-temperature, high-power coherent microwave sources.

quant-ph↗

arXiv2024

Cavity-QED Simulation of a Maser beyond the Mean-Field Approximation

Based on the well-known Tavis-Cummings (TC) model of cavity quantum electrodynamics (QED), we introduce a method for quantum-mechanically simulating the dynamics of experimental masers beyond the mean-field approximation (MFA) that takes into account the spatial variation of the a.c. magnetic field of the maser's amplified microwave mode across its gain medium. The distribution in the coupling between the amplified mode and the medium's very large number (typically $10^{17}$) of spatially distributed quantum emitters can be determined straightforwardly for a given geometry and composition using an electromagnetic-field solver. Upon discretising this distribution as a histogram over a small finite number of bins, we assign -- as an approximation -- the same coupling to all emitters that fall within the same bin, where the value of this coupling equals the center value of the bin's range. With our approximate Hamiltonian arranged as a weighted sum over these bins, we generate expressions for expectation values of operators in the Heisenberg picture to second order in cumulant expansion, using the publicly available QuantumCumulants.jl package in Julia. For ten evenly spaced bins, our model, which can be run on a laptop computer, is used to simulate the recorded output from an experimental maser with a pentacene-doped para-terphenyl gain medium. We find that it replicates the quantum-mechanical features of the measured maser's dynamics, in particular its damped collective Rabi oscillations, more closely than the standard TC model under the MFA can, with an R$^2$ value of 0.774, as opposed to 0.265. Our model should thus aid the quantitative engineering of improved, optimised maser designs.

quant-ph↗

arXiv2024

Surveying optically addressable spin qubits for quantum information and sensing technology

Quantum technologies offer ways to solve certain tasks more quickly, efficiently, and with greater precision than their classical counterparts. Yet substantial challenges remain in the construction of sufficiently error-free and scalable quantum platforms needed to unlock any real benefits to society. Acknowledging that this hardware can take vastly different forms, our review here focuses on so-called spintronic (\textit{i.e.}~spin-electronic) materials that use electronic or nuclear spins to embody qubits. Towards helping the reader to spot trends and pick winners, we have surveyed the various families of optically addressable spin qubits and attempted to benchmark and identify the most promising ones in each. We go on to reveal further trends that demonstrate how qubit lifetimes depend on the material's synthesis, the concentration/distribution of its embedded qubits, and the experimental conditions.

quant-ph↗

arXiv2024

Room-temperature self-cavity lasing from organic color centers

Color centers, which are point defects in crystals, play a crucial role in altering the optical properties of their host materials, enabling widespread applications in the field of quantum information processing. While the majority of the state-of-the-art color centers are inorganic, they come with limitations such as the challenging material preparations and insufficient amount of available centers. In contrast, organic color centers have recently gained attention due to their ease of preparations and tailorable functionalities. Here, pentacene-doped p-terphenyl (Pc:Ptp), an organic color-center system normally used for microwave quantum electronics, is demonstrated for the first time its ability of self-cavity laser emission at room temperature. The laser emission is characterized by strong polarization and high anisotropy, attributed to the unique packing of the color-center molecules within the crystal. The optical coherence is found to be a figure of merit to distinguish the processes of the amplified spontaneous emission (ASE) and lasing in Pc:Ptp. This work highlights the potential of Pc:Ptp as a compact and efficient platform for light-matter interactions , offering significant promise for enhancing the performance of solid-state quantum devices based on this organic color-center system.

physics.optics↗

arXiv2024

Unlocking the Potential of Photoexcited Molecular Electron Spins for Room Temperature Quantum Information Processing

Future information processing technologies like quantum memory devices have the potential to store and transfer quantum states to enable quantum computing and networking. A central consideration in practical applications for such devices is the nature of the light-matter interface which determines the storage state density and efficiency. Here, we employ an organic radical, $\alpha$,$\gamma$-bisdiphenylene-$\beta$-phenylallyl (BDPA) doped into an o-terphenyl host to explore the potential for using tuneable and high-performance molecular media in microwave-based quantum applications. We demonstrate that this radical system exhibits millisecond-long spin-lattice relaxation and microsecond-long phase memory times at room temperature, while also having the capability to generate an oscillating spin-polarized state using a co-dissolved photo-activated tetraphenylporphyrin moiety, all enabled by using a viscous liquid host. This latest system builds upon collective wisdom from previous molecules-for-quantum literature by combining careful host matrix selection, with dynamical decoupling, and photoexcited triplet-radical spin polarisation to realise a versatile and robust quantum spin medium.

cond-mat.mtrl-sci↗

arXiv2024

Overcoming the Thermal-Noise Limit of Microwave Measurements by Pre-cooling with an Active Cold Load

We introduce a method, which we here name ``active pre-cooling'' (APC), for removing, just prior to performing a measurement, a large fraction of the deleterious thermal photons that would otherwise occupy the electromagnetic modes of a microwave cavity or some alternative form of radio-frequency resonator. The removal is achieved by temporarily over-coupling the cavity's modes to an active cold load (ACL). We report a room-temperature bench-top demonstration of the method, where this load takes the form of the input of a commercial low-noise amplifier (LNA). No isolator is inserted between the LNA's input and the cavity's coupling port. The noise temperature of a monitored microwave mode drops to 123 K. Upon incorporating our pre-coolable cavity into a time-resolved (tr-) EPR spectrometer, a commensurate improvement in the signal-to-noise ratio is observed, corresponding to a factor-of-5 speed up over a conventional tr-EPR measurement at room temperature for the same precision and/or sensitivity. Modeling indicates the feasibility, for realistic mode quality factors and couplings, of cooling the room-temperature cavity's modes down to a few tens of K, and for this coldness to last several tens of microseconds, whilst the cavity and its contents are optimally interrogated by a microwave tone or pulse sequence. The method thus provides a simple and generally applicable approach to improving the sensitivity and/or read-out speed in pulsed and time-resolved EPR spectroscopy, quantum detection and other radiometric measurements. It provides a first-stage cold reservoir (of microwave photons) for other, deeper cooling methods to work from and, through the use of cryogenic ACLs (realized, in the first instance, as the inputs of existing cryogenic low-noise amplifiers), the method could itself be directly extended to lower temperature regimes.

quant-ph↗

arXiv2024

Ultra-sensitive solid-state organic molecular microwave quantum receiver

High-accuracy microwave sensing is widely demanded in various fields, ranging from cosmology to microwave quantum technology. Quantum receivers based on inorganic solid-state spin systems are promising candidates for such purpose because of the stability and compatibility, but their best sensitivity is currently limited to a few pT/$\sqrt{\rm{Hz}}$. Here, by utilising an enhanced readout scheme with the state-of-the-art solid-state maser technology, we develop a robust microwave quantum receiver functioned by organic molecular spins at ambient conditions. Owing to the maser amplification, the sensitivity of the receiver achieves 6.14 $\pm$ 0.17 fT/$\sqrt{\rm{Hz}}$ which exceeds three orders of magnitude than that of the inorganic solid-state quantum receivers. The heterodyne detection without additional local oscillators improves bandwidth of the receiver and allows frequency detection. The scheme can be extended to other solid-state spin systems without complicated control pulses and thus enables practical applications such as electron spin resonance spectroscopy, dark matter searches, and astronomical observations.

quant-ph↗

arXiv2023

Tailoring coherent microwave emission from a solid-state hybrid system for room-temperature microwave quantum electronics

Quantum electronics operating in the microwave domain are burgeoning and becoming essential building blocks of quantum computers, sensors and communication devices. However, the field of microwave quantum electronics has long been dominated by the need for cryogenic conditions to maintain the delicate quantum characteristics. Here we report on a solid-state hybrid system, constituted by a photo-excited pentacene triplet spin ensemble coupled to a dielectric resonator, that is for the first time capable of both coherent microwave quantum amplification and oscillation at X band via the masing process at room temperature. By incorporating external driving and active dissipation control into the hybrid system, we achieve efficient tuning of the maser emission characteristics at around 9.4 GHz, which is key to optimizing the performance of the maser device. Our work not only pushes the boundaries of the operating frequency and functionality of the existing pentacene masers, but also demonstrate a universal route for controlling the masing process at room temperature, highlighting opportunities for optimizing emerging solid-state masers for quantum information processing and communication.

quant-ph↗

arXiv2023

`Maser-in-a-Shoebox': a portable plug-and-play maser device at room-temperature and zero magnetic-field

Masers, the microwave analogues of lasers, have seen a renaissance owing to the discovery of gain media that mase at room-temperature and zero-applied magnetic field. However, despite the ease with which the devices can be demonstrated under ambient conditions, achieving the ubiquity and portability which lasers enjoy has to date remained challenging. We present a maser device with a miniaturized maser cavity, gain material and laser pump source that fits within the size of a shoebox. The gain medium used is pentacene-doped in para-terphenyl and it is shown to give a strong masing signal with a peak power of -5 dBm even within a smaller form factor. The device is also shown to mase at different frequencies within a small range of 1.5 MHz away from the resonant frequency. The portability and simplicity of the device, which weighs under 5 kg, paves the way for demonstrators particularly in the areas of low-noise amplifiers, quantum sensors, cavity quantum electrodynamics and long-range communications.

quant-ph↗

arXiv2023

Towards simultaneous coherent radiation in the visible and microwave bands with doped molecular crystals

Coherent sources exploiting the stimulated emission of non-equilibrium quantum systems, i.e. gain media, have proven indispensable for advancing fundamental research and engineering. The operating electromagnetic bands of such coherent sources have been continuously enriched for increasing demands.Nevertheless, for a single bench top coherent source, simultaneous generation of radiation in multiple bands, especially when the bands are widely separated, present formidable challenges with a single gain medium. Here, we propose a mechanism of simultaneously realizing the stimulated emission of radiation in the visible and microwave bands, i.e. lasing and masing actions, at ambient conditions by utilizing photoexcited singlet and triplet states of the pentacene molecules that are doped in p-terphenyl. The possibility is validated by the observed amplified spontaneous emission (ASE) at 645 nm with a narrow linewidth around 1 nm from the pentacene-doped p-terphenyl crystal used for masing at 1.45 GHz and consolidated by a 20 fold lower threshold of ASE compared to the reported masing threshold. The overall threshold of the pentacene-based multiband coherent source can be optimized by appropriate alignment of the pump-light polarization with the pentacene's transition dipole moment. Our work not only shows a great promise on immediate realization of multiband coherent sources but also establishes an intriguing solid-state platform for fundamental research of quantum optics in multiple frequency domains.

physics.optics↗

arXiv2022

Superradiant Masing with Solid-state Spins at Room Temperature

Steady-state superradiance and superradiant lasing attract significant attentions in the field of optical lattice clocks, but have not been achieved so far due to the technical challenges and atom loss problem. In this article, we propose that their counter-part may be observed in the microwave domain with solid-state spins-microwave resonator systems at room temperature with realistic technical restrictions. To validate our proposal, we investigate systematically the system dynamics and steady-state by solving quantum master equations for the multi-level and multi-process dynamic of trillions of spins. To this end, we employ a mean-field approach, and convert the mean-field dynamics of the spin ensemble into the one in a more intuitive Dicke state picture. Our calculations show that for systems with nitrogen vacancy center spins and pentacene molecular spins the superradiant Rabi oscillations occur firstly due to transitions among different Dicke states, and the subsequent continuous-wave superradiant masing can achieve a linewidth well below millihertz. Our work may guide further exploration of transient and steady-state superradiant masing with the mentioned and other solid-state spins systems, such as silicon vacancy centers in silicon carbide and boron vacancy centers in hexagonal boron nitride, where the coherent radiation with ultra-narrow linewidth may find applications in deep-space communications, radio astronomy and high-precision metrology.

quant-ph↗

arXiv2022

Move aside pentacene: Diazapentacene doped para-terphenyl as a zero-field room-temperature maser with strong coupling for cavity quantum electrodynamics

Masers, the microwave analogue of lasers, promise to deliver ultra-low noise amplification of microwave signals for use in medical MRI imaging and deep-space communication. Research on masers in modern times was rekindled thanks to the discovery of gain media that were operable at room-temperature, eschewing bulky cryogenics that hindered their use. However, besides the two known materials of pentacene doped in para-terphenyl and negatively-charged nitrogen-vacancy defects in diamond, there has been scarce progress in the search for completely new room-temperature gain media. Here we show the discovery of 6,13-diazapentacene doped in para-terphenyl as a maser gain medium that can operate at room-temperature and without an external magnetic field. A measured maser pulse power of -10 dBm shows it is on par with pentacene-doped para-terphenyl in absolute power, while possessing compelling advantages against its pentacene predecessor in that it has a faster amplification startup time, can be excited with longer wavelength light at 620 nm and enjoys greater chemical stability from added nitrogen groups. Furthermore, we show that the maser bursts allow 6,13-diazapentacene-doped para-terphenyl to reach the strong coupling regime for cavity quantum electrodynamics, where it has a high cooperativity of 182. We study the optical and microwave spin dynamics of 6,13-diazapentacene-doped para-terphenyl in order to evaluate its behavior as a maser gain medium, where it features fast intersystem crossing and an advantageously higher triplet quantum yield. Our results pave the way for the future discovery of other similar maser materials and help point to such materials as promising candidates for the study of cavity quantum electrodynamic effects at room-temperature.

quant-ph↗

arXiv2022

Enhanced quantum sensing with room-temperature solid-state masers

Quantum sensing with solid-state systems finds broad applications in diverse areas ranging from material and biomedical sciences to fundamental physics. Several solid-state spin sensors have been developed, facilitating the ultra-sensitive detection of physical quantities such as magnetic and electric fields and temperature. Exploiting collective behaviour of non-interacting spins holds the promise of pushing the detection limit to even lower levels, while to date, those levels are scarcely reached due to the broadened linewidth and inefficient readout of solid-state spin ensembles. Here, we experimentally demonstrate that such drawbacks can be overcome by newly reborn maser technology at room temperature in the solid state. Owing to maser action, we observe a 4-fold reduction in the inhomogeneously broadened linewidth of a molecular spin ensemble, which is narrower than the same measured from single spins at cryogenic temperatures. The maser-based readout applied to magnetometry showcases a signal-to-noise ratio (SNR) of 30 dB for single shots. This technique would be a significant addition to the toolbox for boosting the sensitivity of solid-state ensemble spin sensors.

quant-ph↗

arXiv2021

Quasi-Continuous Cooling of a Microwave Mode on a Benchtop using Hyperpolarized NV$^-$ Diamond

We demonstrate the cooling of a microwave mode at 2872 MHz through its interaction with optically spin-polarized NV$^-$ centers in diamond at zero applied magnetic field, removing thermal photons from the mode. By photo-exciting (pumping) a brilliant-cut red diamond jewel with a continuous-wave 532-nm laser, outputting 2 W, the microwave mode is cooled down to a noise temperature of 188 K. This noise temperature can be preserved continuously for as long as the diamond is optically excited and kept cool. The latter requirement restricted operation out to 10 ms in our preliminary setup. The mode-cooling performance of NV$^-$ diamond is directly compared against that of pentacene-doped para-terphenyl, where we find that the former affords the advantages of cooling immediately upon light excitation without needing to mase beforehand (or at all) and being able to cool continuously at substantially lower optical pump power.

quant-ph↗