arXiv Science⌕ Search

arXiv subjects

M. Winkel

Publications and source records attributed to M. Winkel.

5 recordsLinked to original sources

High-power X-Point Target divertor experiments on the TCV tokamak

Stationary power exhaust in the X-Point Target (XPT) divertor configuration is investigated in high-power ($2.5\,\text{MW}$) TCV L-mode discharges, in which the Lengyel detachment scaling metric $P_{\text{SOL}}B_{0}/(R_{0}n_{e,\text{u}}^{2})$ lies in the range expected for reactors (SPARC, ITER, ARC). Compared with a conventional single-null (SN) divertor, the XPT improves power exhaust performance, reducing the peak outer target heat flux by 40--60\% and enabling divertor detachment with nitrogen seeding under conditions in which the SN cannot be detached. Detachment evolves asymmetrically across the multiple XPT outer strike points. The sensitivities of the peak target heat fluxes and impurity emission front positions to the X-point separation ($\text{d}R_{\text{u},X2}$) are characterized and found to decrease at higher nitrogen seeding levels. Field-reversal experiments reveal the critical role of $E\times B$ drifts inherent to the magnetic topology of the secondary X-point, which drive an unconventional redistribution of density and impurity radiation in the XPT divertor and thereby cause the asymmetries between the XPT outer strike points, largely confirming the expectations from recent SOLPS-ITER modelling. A framework for understanding the power exhaust physics of the XPT is presented, detailing the roles of SOL splitting, connection length peaking, $E\times B$ drifts, and vessel geometry. Together, these results establish an experimental physics basis for the XPT divertor as a potential power exhaust solution for tokamak reactors.

physics.plasm-ph↗

Detachment dynamics and disturbance rejection in the TCV X-Point Target divertor

The X-Point Target (XPT) is an alternative divertor configuration with a secondary X-point in the divertor leg. We investigate its detachment dynamics and disturbance rejection capacity on the TCV tokamak, comparing it with a long-legged single-null (SN) divertor. We employ a system identification approach using multi-sine perturbations to D$_2$ fuelling in Ohmic L-mode scenarios and to N$_2$ seeding and electron cyclotron resonance heating (ECRH) power in auxiliary-heated L-mode scenarios, using the CIII emission front position as a proxy for the detached state evolution. For D$_2$ fuelling perturbations at 4-31 Hz, the gain of the front response at the secondary X-point is at least a factor of 3 lower than upstream of it, where the response is similar to that of the SN. This indicates that the reduced detachment sensitivity of the secondary X-point in an XPT configuration previously observed in quasi-steady state experiments, extends to control-relevant timescales as an enhanced disturbance rejection capacity. In auxiliary-heated scenarios, the CIII front in the XPT remains nearly stationary near the secondary X-point under N$_2$ seeding and ECRH power perturbations, whereas the CIII front in SN discharges responds strongly. However, due to complex SOL profiles in the region close to the secondary X-point of the XPT configuration, this reduction in CIII front response may not imply disturbance rejection of the detached state as a whole. The enhanced disturbance rejection at the secondary X-point could provide a passive buffer against disturbances, simplifying the task of exhaust controllers to maintain the detached state throughout a discharge cycle.

physics.plasm-ph↗

High-power TCV scenario for conventional and alternative divertor studies

Alternative divertor configurations (ADCs) must be evaluated under boundary plasma conditions approaching reactor-level values to be considered a reliable, physics-based solution for tokamak power exhaust. Most ADC experiments performed to date were at relatively low exhaust power. This work presents a high-power scenario on the TCV tokamak enabling the study of a wide variety of divertor magnetic shapes under an expanded SOL and power exhaust parameter space. The scenario is characterized by high power levels of electron cyclotron resonance heating ($2.5\,\text{MW}$ fully absorbed in a $\sim1\,\text{m}^{3}$ plasma) at high plasma current (edge safety factor $q_{95}\approx 2.5$), and low upstream separatrix densities ($n_{e,\text{u}}\approx1\times10^{19}\,\text{m}^{-3}$, Greenwald fraction $f_{\text{G}}\approx 0.1$). Stationary parallel heat fluxes up to $100\,\text{MW m}^{-2}$ are measured at the divertor target, an order of magnitude above previous TCV power exhaust studies. The obtained SOL collisionality and Lengyel detachment scaling metric lie within range of values expected in future reactors (SPARC, ITER, ARC).

physics.plasm-ph↗

Optical conductivity of warm dense matter in wide frequency range within quantum statistical and kinetic approach

Fundamental properties of warm dense matter are described by the dielectric function, which gives access to the frequency-dependent electrical conductivity, absorption, emission and scattering of radiation, charged particles stopping and further macroscopic properties. Different approaches to the dielectric function and the related dynamical collision frequency are compared in a wide frequency range. The high-frequency limit describing inverse bremsstrahlung and the low-frequency limit of the dc conductivity are considered. Sum rules and Kramers-Kronig relation are checked for the generalized linear response theory and the standard approach following kinetic theory. The results are discussed in application to aluminum, xenon and argon plasmas.

physics.plasm-ph↗

Particle identification using clustering algorithms

A method that uses fuzzy clustering algorithms to achieve particle identification based on pulse shape analysis is presented. The fuzzy c-means clustering algorithm is used to compute mean (principal) pulse shapes induced by different particle species in an automatic and unsupervised fashion from a mixed set of data. A discrimination amplitude is proposed using these principal pulse shapes to identify the originating particle species of a detector pulse. Since this method does not make any assumptions about the specific features of the pulse shapes, it is very generic and suitable for multiple types of detectors. The method is applied to discriminate between photon- and proton-induced signals in CsI(Tl) scintillator detectors and the results are compared to the well-known integration method.

physics.ins-det↗