arXiv subjects

Liang Hu

Publications and source records attributed to Liang Hu.

89 records · Page 5Linked to original sources

arXiv2021

Branching optical frequency transfer with enhanced post automatic phase noise cancellation

We present a technique for coherence transfer of laser light through a branching fiber link, where the optical phase noise induced by environmental perturbations via the fiber link is passively compensated by remote users without the requirements of any active servo components. At each remote site, an acousto-optic modulator (AOM) is simultaneously taken as a frequency distinguisher for distinguishing its unique frequency from other sites' and as an optical actuator for compensating the phase noise coming from the optical fiber. With this configuration, we incorporate a long outside loop path consisting of a fiber-pigtailed AOM into the loop, enabling the significant reduction of the outside loop phase noise in the passive way. To further address the residual out-of-loop phase noise coming from the interferometer and the two-way optical frequency comparison setup, we design a low-noise active temperature stabilization system. Measurements with a back-to-back system show that the stability in our stabilization system is $2\times10^{-16}$ at 1 s, reaching $2\times10^{-20}$ after 10,000 s. Adopting these techniques, we demonstrate transfer of a laser light through a branching fiber network with 50 km and 145 km two fiber links. After being compensated for the 145 km fiber link, the relative frequency instability is $3.4\times10^{-15}$ at the 1 s averaging time and scales down to $3.7\times10^{-19}$ at the 10,000 s averaging time. This proposed technique is suitable for the simultaneous transfer of an optical signal to a number of independent users within a local area.

physics.ins-det↗

arXiv2021

Passive Optical Phase Stabilization on a Ring Fiber Network

Optical frequency transfer provides the means for high-fidelity frequency transfer across thousands of kilometers. A critical step in the further developing optical frequency transfer is its capability to transfer a high spectral purity feature from ultrastable lasers or optical clocks to any remote locations and, at the same time, its adaptability to incorporate the optical frequency transfer technique into any existing communication networks with different topologies. Here we for the first time report a technique that delivers optical-frequency signals to multiple independent remote hubs along a ring optical-fiber network with passive phase stabilization. The technique automatically corrects optical-fiber length fluctuations of arbitrary hubs along the loop by mixing and shifting optical signals. Without the help of an active phase tracker and a compensator, it could significantly mitigate some technical problems such as the limited compensation speed and phase recovery time, the phase jitter contamination caused by the servo bump in conventional phase noise cancellation. Moreover, by transmitting optical signals along both directions using the same optical source, it can improve the signal-to-noise ratio at each hub. This technique maintains the same delay-limited phase noise correction capability as in conventional techniques and, furthermore, improves the phase jitter by a factor of 3, opening a way to a broad distribution of an ultrastable frequency reference with high spectral purity and enabling a wide range of applications beyond metrology over a ring fiber network with the naturally impressive reliability and scalability.

physics.ins-det↗

arXiv2021

All-passive multiple-place optical phase noise cancellation

We report on the realization of delivering coherent optical frequency to multiple places based on passive phase noise cancellation over a bus topology fiber network. This technique mitigates any active servo controller on the main fiber link and at arbitrary access places as opposed to the conventional technique, in which an active phase compensation circuit has to be adopted to stabilize the main fiber link. Although the residual fiber phase noise power spectral density (PSD) in the proposed technique turns out to be a factor of 7 higher than that of in the conventional multiple-access technique when the access place is close to the end of the fiber link, it could largely suppress the phase noise introduced by the servo bumps, improve the response speed and phase recovery time, and minimize hardware overhead in systems with many stations and connections without the need of the active servo circuits including phase discriminators and active compensators. The proposed technique could considerably simplify future efforts to make precise optical frequency signals available to many users, as required by some large-scale science experiments.

physics.ins-det↗

arXiv2021

Lyapunov-Based Reinforcement Learning State Estimator

In this paper, we consider the state estimation problem for nonlinear stochastic discrete-time systems. We combine Lyapunov's method in control theory and deep reinforcement learning to design the state estimator. We theoretically prove the convergence of the bounded estimate error solely using the data simulated from the model. An actor-critic reinforcement learning algorithm is proposed to learn the state estimator approximated by a deep neural network. The convergence of the algorithm is analysed. The proposed Lyapunov-based reinforcement learning state estimator is compared with a number of existing nonlinear filtering methods through Monte Carlo simulations, showing its advantage in terms of estimate convergence even under some system uncertainties such as covariance shift in system noise and randomly missing measurements. To the best of our knowledge, this is the first reinforcement learning based nonlinear state estimator with bounded estimate error performance guarantee.

cs.LG↗

arXiv2020

Jointly Modeling Intra- and Inter-transaction Dependencies with Hierarchical Attentive Transaction Embeddings for Next-item Recommendation

A transaction-based recommender system (TBRS) aims to predict the next item by modeling dependencies in transactional data. Generally, two kinds of dependencies considered are intra-transaction dependency and inter-transaction dependency. Most existing TBRSs recommend next item by only modeling the intra-transaction dependency within the current transaction while ignoring inter-transaction dependency with recent transactions that may also affect the next item. However, as not all recent transactions are relevant to the current and next items, the relevant ones should be identified and prioritized. In this paper, we propose a novel hierarchical attentive transaction embedding (HATE) model to tackle these issues. Specifically, a two-level attention mechanism integrates both item embedding and transaction embedding to build an attentive context representation that incorporates both intraand inter-transaction dependencies. With the learned context representation, HATE then recommends the next item. Experimental evaluations on two real-world transaction datasets show that HATE significantly outperforms the state-ofthe-art methods in terms of recommendation accuracy.

cs.IR↗

arXiv2020

Graph Learning Approaches to Recommender Systems: A Review

Recent years have witnessed the fast development of the emerging topic of Graph Learning based Recommender Systems (GLRS). GLRS mainly employ the advanced graph learning approaches to model users' preferences and intentions as well as items' characteristics and popularity for Recommender Systems (RS). Differently from conventional RS, including content based filtering and collaborative filtering, GLRS are built on simple or complex graphs where various objects, e.g., users, items, and attributes, are explicitly or implicitly connected. With the rapid development of graph learning, exploring and exploiting homogeneous or heterogeneous relations in graphs is a promising direction for building advanced RS. In this paper, we provide a systematic review of GLRS, on how they obtain the knowledge from graphs to improve the accuracy, reliability and explainability for recommendations. First, we characterize and formalize GLRS, and then summarize and categorize the key challenges in this new research area. Then, we survey the most recent and important developments in the area. Finally, we share some new research directions in this vibrant area.

cs.IR↗

arXiv2020

Fundamental Limitations of Rayleigh Backscattering Noise on Fiber-Based Multiple-Access Optical Frequency Transfer

While it has been shown that backscattering induced phase noise can be suppressed by adopting acoustic-optic-modulators (AOMs) at the local and remote sites to break the frequency symmetry in both directions. However, this issue can not be avoided for conventional fiber-optic multiple-access coherent optical phase dissemination in which the interference of the signal light with the Rayleigh backscattered light will probably destroy the coherence of the stabilized optical signal. We suppress the backscattering effect by locally breaking the frequency symmetry at the extraction point by inserting an additional AOM. Here, we theoretically analyze and experimentally demonstrate an add-drop one more AOM approach for suppressing the Rayleigh backscattering within the fiber link. Near-complete suppression of backscattering noise is experimentally confirmed through the measurement the elimination of a common interference term of the signal light and the Rayleigh backscattered light. The results demonstrate that the Rayleigh backscattering light has a limited effect compared to the residual delay-limited fiber phase noise on the system's performance. Our results also provide new evidence that it is possible to largely suppress Rayleigh and other backscattering noise within a long optical fiber link, where the accumulated phase noise could be large, by using frequency symmetry breaking at each access node to achieve robust multiple-access coherent optical phase propagation in spite of scatters or defects.

physics.ins-det↗

arXiv2020

Passive Optical Phase Noise Cancellation

We report on the realization of an optical phase noise cancellation technique by passively embedding the optical phase information into a radio frequency (RF) signal and shifting the optical frequency with the amount of phase noise introduced by optical phase perturbations. Neither phase discrimination nor active phase tracking is required due to the open-loop design, mitigating some technical problems, such as the limited compensation speed and the finite phase/timing jitter, in conventional phase noise cancellation. We experimentally demonstrate that this technique maintains the same delay-limited bandwidth and phase noise suppression capability as in conventional techniques, but significantly shortens the response speed and phase recovery time. Passive decoupling optical phase perturbation represents a powerful technique in the domains of optical frequency standard comparisons and clockworks for future optical atomic clocks, which are now under serious investigation for a potential redefinition of the International Time Scale.

physics.ins-det↗

arXiv2020

Multi-node optical frequency dissemination with post automatic phase correction

We report a technique for coherence transfer of laser light through a fiber link, where the optical phase noise induced by environmental perturbation via the fiber link is compensated by remote users with passive phase noise correction, rather than at the input as is conventional. Neither phase discrimination nor active phase tracking is required due to the open-loop design, mitigating some technical problems such as the limited compensation speed and the finite compensation precision as conventional active phase noise cancellation. We theoretically analyze and experimentally demonstrate that the delay effect introduced residual fiber phase noise after noise compensation is a factor of 7 higher than the conventional techniques. Using this technique, we demonstrate the transfer laser light through a 145-km-long, lab-based spooled fiber. After being compensated, the relative frequency instability in terms of overlapping Allan deviation is 1.9E-15 at 1s averaging time and scales down 5.3E-19 at 10,000 s averaging time. The frequency uncertainty of the light after transferring through the fiber relative to that of the input light is -0.36+-2.6E-18. As the transmitted optical signal remains unaltered until it reaches the remote sites, it can be transmitted simultaneously to multiple remote sites on an arbitrarily complex fiber network, paving a way to develop a multi-node optical frequency dissemination system with post automatic phase noise correction for a number of end users.

physics.optics↗

arXiv2019

Sequential Recommender Systems: Challenges, Progress and Prospects

The emerging topic of sequential recommender systems has attracted increasing attention in recent years.Different from the conventional recommender systems including collaborative filtering and content-based filtering, SRSs try to understand and model the sequential user behaviors, the interactions between users and items, and the evolution of users preferences and item popularity over time. SRSs involve the above aspects for more precise characterization of user contexts, intent and goals, and item consumption trend, leading to more accurate, customized and dynamic recommendations.In this paper, we provide a systematic review on SRSs.We first present the characteristics of SRSs, and then summarize and categorize the key challenges in this research area, followed by the corresponding research progress consisting of the most recent and representative developments on this topic.Finally, we discuss the important research directions in this vibrant area.

cs.IR↗

arXiv2019

Sr atom interferometry with the optical clock transition as a gravimeter and a gravity gradiometer

We characterize the performance of a gravimeter and a gravity gradiometer based on the $^{1}$S$_{0}$-$^3$P$_0$ clock transition of strontium atoms. We use this new quantum sensor to measure the gravitational acceleration with a relative sensitivity of $1.7\times10^{-5}$, representing the first realisation of an atomic interferometry gravimeter based on a single-photon transition. Various noise contributions to the gravimeter are measured and characterized, with the current primary limitation to sensitivity seen to be the intrinsic noise of the interferometry laser itself. In a gravity gradiometer configuration, a differential phase sensitivity of 1.53~rad/$\sqrt{Hz}$ was achieved at an artificially introduced differential phase of $π/2$~rad. We experimentally investigated the effects of the contrast and visibility based on various parameters and achieve a total interferometry time of 30~ms, which is longer than previously reported for such interferometers. The characterization and determined limitations of the present apparatus employing $^{88}$Sr atoms provides a guidance for the future development of large-scale clock-transition gravimeters and gravity gradiometers with alkali-earth and alkali-earth-like atoms (e.g., $^{87}$Sr, Ca, Yb).

physics.atom-ph↗

arXiv2019

Super-Exchange Theory for Polyvalent Anion Magnets

The Goodenough-Kanamori-Anderson (GKA) rules have been widely applied for explaining the magnetic properties induced by super-exchange interaction. As conclusions of the super-exchange theory, they reveal the antiferromagnetic (ferromagnetic) ordering along with bond angle of 180 degrees (90 degrees) in the cation-anion-cation interaction path, in which the theory sets a pre-condition that the electronic states of cations in all paths are identical. We observed that the GKA rules are in fact not universal and even invalid to materials containing anions with different valence states, for example, the layered CrOCl crystal (with two valence states of anions: O2- and Cl-). In this study, we propose an extended super-exchange theory (ESET) related to superposed electronic states of cation in a specific path. ESET is capable of predicting not only the sign and relative magnitude of magnetic exchange constants in different cation-anion-cation paths, but also the magnetic ground state. Through our proposed theory, we conclude that the magnetic ordering along with bond angle of 90 degrees in Cr-Cl-Cr path is moderately antiferromagnetic and of 180 degrees in Cr-O-Cr path is strongly ferromagnetic, which are opposite to the contents of GKA rules. Moreover, we clarify that monolayer CrOCl has antiferromagnetic ordering rather than ferromagnetic as reported recently. The reliability of ESET is verified via first-principles calculation and previous experimental report as well, and its universality is also demonstrated. Thus, our theory is powerful to predict the magnetic properties, which makes it possible to design new high Curie temperature two-dimensional semiconducting ferromagnets with polyvalent anion materials.

cond-mat.mtrl-sci↗

arXiv2017

Bragg gravity-gradiometer using the $^1$S$_0$-$^3$P$_1$ intercombination transition of $^{88}$Sr

We present a gradiometer based on matter-wave interference of alkaline-earth-metal atoms, namely $^{88}$Sr. The coherent manipulation of the atomic external degrees of freedom is obtained by large-momentum-transfer Bragg diffraction, driven by laser fields detuned away from the narrow $^1$S$_0$-$^3$P$_1$ intercombination transition. We use a well-controlled artificial gradient, realized by changing the relative frequencies of the Bragg pulses during the interferometer sequence, in order to characterize the sensitivity of the gradiometer. The sensitivity reaches $1.5 \times 10^{-5}$ s$^{-2}$ for an interferometer time of 20 ms, limited only by geometrical constraints. We observed extremely low sensitivity of the gradiometric phase to magnetic field gradients, approaching a value 10$^{5}$ times lower than the sensitivity of alkali-atom based gradiometers. An efficient double-launch technique employing accelerated red vertical lattices from a single magneto-optical trap cloud is also demonstrated. These results highlight strontium as an ideal candidate for precision measurements of gravity gradients, with potential application in future precision tests of fundamental physics.

physics.atom-ph↗

arXiv2017

Robust and Pristine Top ological Dirac Semimetal Phase in Pressured Two-Dimensional Black Phosphorous

Very recently, in spite of various efforts in searching for two dimensional topological Dirac semimetals (2D TDSMs) in phosphorene, there remains a lack of experimentally efficient way to activate such phase transition and the underlying mechanism for the topological phase acquisition is still controversial. Here, from first-principles calculations in combination with a band-sorting technique based on k.p theory, a layer-pressure topological phase diagram is obtained and some of the controversies are clarified. We demonstrate that, compared with tuning by external electric-fields, strain or doping by adsorption, hydrostatic pressure can be an experimentally more feasible way to activate the topological phase transition for 2D TDSM acquisition in phosphorene. More importantly, the resultant TDSM state is a pristine phase possessing a single pair of symmetry-protected Dirac cones right at the Fermi level, in startling contrast to the pressured bulk black phosphorous where only a carrier-mixed Dirac state can be obtained. We corroborate that the Dirac points are robust under external perturbation as long as the glide-plane symmetry preserves. Our findings provide a means to realize 2D pristine TDSM in a more achievable manner, which could be crucial in the realization of controllable TDSM states in phosphorene and related 2D materials.

cond-mat.mes-hall↗

arXiv2017

Atom interferometry with the Sr optical clock transition

We report on the realization of a matter-wave interferometer based on single-photon interaction on the ultra-narrow optical clock transition of strontium atoms. We experimentally demonstrated its operation as a gravimeter and as a gravity gradiometer. No reduction of interferometric contrast was observed up to an interferometer time $2T=10$ ms, limited by geometric constraints of the apparatus. In the gradiometric configuration, the sensitivity approaches the shot noise limit. Single-photon interferometers represent a new class of high-precision sensors that could be used for the detection of gravitational waves in so far unexplored frequency ranges and to enlighten the boundary between Quantum Mechanics and General Relativity.

physics.atom-ph↗

arXiv2017

Exact solutions to the (1+1)-dimensional nonlinear Maxwell equations in the orthogonal curvilinear coordinates

Characterizing electromagnetic wave propagation in nonlinear and inhomogeneous media is of great interest from both theoretical and practical perspectives, even though it is extremely complicated. In fact, it is still an unresolved issue to find the exact solutions to the nonlinear waves in the orthogonal curvilinear coordinates. In this paper, we present an analytic method to handle the problem of electromagnetic waves propagation in arbitrarily nonlinear and particularly inhomogeneous media without dispersion. Through the exact solutions of the (1+1)-dimensional nonlinear Maxwell equations, we discuss some nonlinear phenomena, including cylindrical shock waves, free nonlinear oscillations, and nonlinear superposition of waves.

physics.class-ph↗

arXiv2016

Orientation Driven Bag of Appearances for Person Re-identification

Person re-identification (re-id) consists of associating individual across camera network, which is valuable for intelligent video surveillance and has drawn wide attention. Although person re-identification research is making progress, it still faces some challenges such as varying poses, illumination and viewpoints. For feature representation in re-identification, existing works usually use low-level descriptors which do not take full advantage of body structure information, resulting in low representation ability. %discrimination. To solve this problem, this paper proposes the mid-level body-structure based feature representation (BSFR) which introduces body structure pyramid for codebook learning and feature pooling in the vertical direction of human body. Besides, varying viewpoints in the horizontal direction of human body usually causes the data missing problem, $i.e.$, the appearances obtained in different orientations of the identical person could vary significantly. To address this problem, the orientation driven bag of appearances (ODBoA) is proposed to utilize person orientation information extracted by orientation estimation technic. To properly evaluate the proposed approach, we introduce a new re-identification dataset (Market-1203) based on the Market-1501 dataset and propose a new re-identification dataset (PKU-Reid). Both datasets contain multiple images captured in different body orientations for each person. Experimental results on three public datasets and two proposed datasets demonstrate the superiority of the proposed approach, indicating the effectiveness of body structure and orientation information for improving re-identification performance.

cs.CV↗