arXiv subjects

Kei Okada

Publications and source records attributed to Kei Okada.

At least 19 recordsLinked to original sources

arXiv2026

LunaDrive: A Delay-Compensated High-Voltage GaN FET-Based Motor Driver for Dynamic Robots with Flat BLDC Motors

The performance improvement of high-power flat BLDC motors has accelerated the development of dynamic robots. However, many commercially available servo motors assume operating voltages of 48 V or lower, which limits the maximum rotational speed. Dynamic robots require rapid energy generation, so this voltage constraint restricts motion performance. Therefore, driving motors beyond the rated voltage is desirable to increase the instantaneous maximum speed. On the other hand, semiconductor devices used in motor drivers have a trade-off between voltage rating and current capacity. Conventional drivers using Si MOSFETs have difficulty achieving both high-voltage and high-current operation. Although GaN FETs are promising, compact drivers that can be mounted on the rear side of flat BLDC motors remain limited. In this study, a motor driver for high-power flat BLDC motors using GaN FETs is developed. The effect of delay compensation in the high-speed region beyond the rated operating range is also investigated. In the experiments, under 96 V operation, a continuous current of 30 A was achieved with a heat sink attached. A peak current of 80 A and a maximum electrical frequency of 3110 Hz were confirmed. A high-speed load lifting experiment driven by a LiPo battery 24S (100 V) was also conducted, demonstrating applicability to dynamic robot operation.

cs.RO↗

arXiv2026

A Morphing Aerial Robot With Thruster-Integrated Flexible Continuum Links for Shape Adaptive Aerial Manipulation

In recent years, aerial manipulation has attracted increasing attention as a key to expand the application of aerial robots. In this work, we focus on two major research directions for achieving versatile aerial manipulation: (i) acquiring high environmental adaptability using soft manipulators, and (ii) expanding the feasible wrench space by distributing thrusters along the manipulator. However, no aerial robot has simultaneously satisfied these two requirements. Therefore, in this paper, we propose a morphing rotor-distributed aerial robot with flexible continuum links that achieves both high shape adaptability and an expanded wrench space. The flexible continuum links function as soft manipulators, passively conforming to the shape of the environment, while the thrusters distributed along the continuum links expand the feasible thrust wrench space and enable the end-effector to exert large interaction forces. To realize the proposed robot, it is essential to suppress vibrations of the lightweight continuum links. Thus, we develop a composite leaf-spring structure that provides both high torsional and vertical stiffness, and vibration-suppressing control methods. Using these implementations, we demonstrate stable flight and a variety of aerial manipulation tasks. To the best of our knowledge, this is the first work to realize aerial manipulations using flexible links with an integrated thruster.

cs.RO↗

arXiv2026

Continuous Manifold-Decomposed Impedance Retargeting for Contact-Rich Imitation Learning

CMDIR extends Manifold-Decomposed Impedance Retargeting (MDIR) to transform fixed-impedance demonstrations into continuous variable-impedance controllers, which can also serve as structured supervision for imitation learning. Continuous Task-Manifold Impedance Representation (TMIR) pairs an evolving task frame with controller instructions. Demo-relative Compromise dynamics retain moving-basis transport and control/physical metric mismatch, yielding displacement, reaction-impulse, and perturbation-sensitivity criteria. Quality-to-Fast automatically compiles a solver structure from development paths within a predefined finite space, re-instantiates that structure for each demonstration, and certifies the resulting candidate by multi-resolution evaluation. Across 225 retargeted-controller trials in three real contact tasks, full CMDIR improves mean task-proxy retention and reduces mean pose deviation, force fluctuation, and peak force relative to discrete MDIR. FastMPO achieves a $5.8$--$9.4\times$ speedup over C-MPO with comparable closed-loop outcomes. Downstream experiments demonstrate learnability of the complete TMIR supervision interface; lower force fluctuation and peak force are observed among successful executions, while completion reliability remains uneven across tasks and environments.

cs.RO↗

arXiv2026

Anti-Gravity Walking by a Flying Humanoid Robot via Thrust-Rate Input Whole-Body Model Predictive Control

Flying humanoids are expected to perform tasks in diverse environments, while their existing locomotion is mainly limited to aerial flight and ground walking. The capability to move in complex three-dimensional space can greatly expand their application range. For such walking motion on ceilings and similar anti-gravity environments, whole-body MPC is effective. However, the discontinuous changes in dynamic structure accompanying contact switching during walking can induce thrust spikes, resulting in control instability. Therefore, in this work, we propose and implement a real-time whole-body MPC framework for anti-gravity bipedal walking. First, we formulate whole-body MPC using the time derivative of thrust, namely thrust-rate, as the control input. This formulation guarantees continuity of the thrust trajectory during contact switching while preserving the sparse structure of the optimal control problem for fast computation. Second, we address the lack of natural support forces in anti-gravity environments. We introduce lower bounds on the foot-normal component of the contact force, and smoothly transfer them during the doublesupport phase. Finally, we implement the proposed framework and demonstrate anti-gravity walking by a flying humanoid through simulation and a hardware experiment. To the best of our knowledge, this is the first demonstration of multi-contact whole-body MPC for a transformable aerial robot and walking by a flying humanoid beyond the ground.

cs.RO↗

arXiv2026

Design of a Biomimetic Joint-Covering Skin with Tissue-Like Structure to Enhance Proprioception in a Musculoskeletal Humanoid

Proprioception in musculoskeletal humanoids is typically estimated primarily from muscle sensing, while the role of cutaneous deformation around joints remains insufficiently explored. In biological systems, mechanoreceptors distributed within soft tissue complement muscle feedback and support reliable joint state estimation. This study presents the design of a biomimetic joint-covering skin with a tissue-like layered structure that integrates pressure- and stretch-sensitive elements within the joint-covering tissue. The proposed skin is implemented on the musculoskeletal humanoid Musashi-W, and its independent proprioceptive capability as well as its integration with muscle sensing are evaluated. Experimental results show that the proposed skin alone achieves joint angle estimation with an average error of approximately 3 degrees. Furthermore, integration with muscle sensing improves estimation accuracy. Owing to its joint-covering structure, the skin may mechanically mitigate the influence of external disturbances on the muscles, and the integration of multiple modalities suggests the possibility of contributing to the identification of external stimuli that are difficult to interpret using muscle sensing alone. This work presents a design methodology for biomimetic joint-covering skin and demonstrates that such tissue-structured skin can serve as an effective approach for extending proprioceptive systems in musculoskeletal humanoids.

cs.RO↗

arXiv2026

Robust Brachiation on a Life-Sized Dual-Arm Robot Using Waypoint-Guided Reinforcement Learning

Brachiation is a form of locomotion in which primates move primarily using their arms, enabling traversal in environments without footholds. However, this motion requires highly coordinated whole-body movement and precise timing control for bar grasping and release. As a result, achieving robust behavior on life-sized robotic platforms remains challenging. In this study, we present a reinforcement learning-based method to realize brachiation on a life-sized dual-arm robot. The core of the proposed approach is Waypoint-Guided Reinforcement Learning (WGRL), a learning framework for inducing non-linear and complex motions. For high-difficulty tasks where imitation learning data are unavailable, WGRL guides behavior acquisition by sparsely specifying waypoints for the end-effector trajectory, while whole-body motion is generated through reinforcement learning. In addition, by integrating the waypoint-following guidance with rewards based on task success and mechanical energy, and training in an environment designed for Sim-to-Real transfer, the proposed method achieves both forward progression and motion stability. The acquired behavior is evaluated through Sim-to-Sim experiments under monkey-bar environments with geometric variations and hardware experiments, confirming robust brachiation including failure recovery behavior. This study provides effective learning design guidelines for realizing arm-based locomotion on life-sized robotic hardware and expanding the traversable workspace of robots.

cs.RO↗

arXiv2026

Detachable Wire Drive : Reconfigurable Robot Architecture with Shared Actuators

Reconfigurable robots offer significant potential for adapting to diverse tasks; however, conventional centralized architectures often require dedicated actuators for each module, leading to substantial increases in overall system weight, volume, and cost. To address these challenges, this paper presents the "Detachable Wire Drive," a reconfigurable robotic system that enables the sharing of heavy and expensive actuators across various morphologies. The core of this system is the "Wire Detach Unit," a mechanism designed to physically split and reconnect wire drive paths, allowing motors to be consolidated into a common base unit. We demonstrate the versatility of this approach by developing a 2-DOF rigid arm, a continuum arm, and two distinct grippers, all of which are interchangeably attached to, and driven by, a single shared actuator set. Experimental results validate the mechanical reliability of the detachment process and the control framework's ability to seamlessly manage transitions between configurations, highlighting a path toward more efficient and multi-functional robotic systems.

cs.RO↗

arXiv2026

Neural Introspection Gating for Adaptive KV-Cache Reuse in Vision-Language-Action Models

Vision-Language-Action(VLA) models map camera images and language instructions directly to motor commands through a single autoregressive transformer. In real-time control, they still spend substantial compute recomputing key-value(KV) representations for visual tokens that barely change across neighboring frames. Recent work such as VLA-Cache reduces that cost by reusing KV states for visually static patches, but its policy relies only on observation-space heuristics and does not account for the model's own uncertainty. We propose Gated VLA-Cache, a lightweight, training-free extension that augments visual-similarity caching with neural introspection. The method monitors the logit margin between the top two predicted action tokens, a zero-cost confidence signal available during decoding. When the margin drops below a threshold, the cache is invalidated and a full recompute is triggered. Evaluated on four LIBERO benchmark suites with both OpenVLA and OpenVLA-OFT, Gated VLA-Cache improves reliability when blind caching hurts. On LIBERO-Goal and LIBERO-Long, it recovers over 100% of the lost accuracy while retaining 80% of the compute savings.

cs.RO↗

arXiv2026

MDIR: A Task-Manifold Impedance Retargeting Method for Contact-Rich Teleoperation

Fixed Cartesian impedance makes contact-rich teleoperation demonstrations practical, but gains that secure progress and contact support also determine impact and force variability. We study single-demonstration controller-to-controller impedance retargeting. Given one fixed Cartesian impedance command sequence {K0, D0, xcmd}, Manifold-Decomposed Impedance Retargeting (MDIR) deterministically reparameterizes the recorded controller into an executable task-channel variable-impedance command. MDIR targets this local retargeting problem by preserving projected task-channel responses near the demonstrated trajectory. It represents the source response in operational work, exertion, and support channels with a passive residual complement under a control-chain metric, computes an executable Cartesian-to-Manifold Retargeting (C2M) baseline, and applies Manifold-Constrained Parameter Optimization (MPO) to select a feasible representative with lower wrist-force peaks, impulse, force variability, and nominal controller power. Across planar wiping, pick-and-place, and pushing on a Franka Panda, the full MDIR controller passes Task Check in all 15 closed-loop executions and reduces all four aggressiveness metrics relative to the fixed-impedance demonstrations.

cs.RO↗

arXiv2026

TRACT: Temporally Routed Action Chunks with Chronological Phase Authority for Contact-Rich Manipulation

Action chunking shortens the effective decision horizon of robot imitation learning by predicting multiple future actions, while conventional phase conditioning describes the current control instant. When a predicted horizon crosses a procedural boundary, assigning the current phase to the entire chunk creates a structural temporal mismatch. We present TRACT, which factorizes phase-structured action chunking into an accepted current phase and a single CURRENT-to-NEXT boundary inside the future horizon. A task-local graph constrains chronological phase authority, and a cumulative boundary distribution monotonically routes future queries through phase-specific query and action paths. For contact execution, a causal response-deficit integrator compares policy intent with ACK-eligible subsequent motion, accumulates arm compensation when directional response is suppressed, and decays after confirmed recovery. Across six real-robot variants with ten trials each, full TRACT achieves 10/10 full-sequence success, 99.00 [88.75, 100.00]% median [min, max] wipe completion, zero observed phase ambiguity, and zero stalls. Under the current complete method package and evaluation setting, the routed representation obtains better observed task results than the flat package (6/10 vs. 3/10 success; 77.08% vs. 8.03% median wipe completion). Chronological authority reduces observed phase ambiguity from 8/10 to 0/10, and response integration reduces stalls from 4/10 to 0/10. The package comparison does not isolate routing from other generator-package differences.

cs.RO↗

arXiv2026

VLAff: Vision-Language-Affordance Model for Unified Actionable Affordances

Learning manipulation skills from human videos is promising for scalable robot learning. However, the embodiment mismatch between humans and robots makes this challenging. One promising solution is to learn object-centric actionable affordances that are embodiment-agnostic. In this work, we propose a framework that leverages egocentric human videos with state-of-the-art 3D Structure-from-Motion and hand mesh reconstruction to extract actionable affordances such as visual, grasp, and trajectory affordances that explicitly encode where to interact, how to grasp, and how to move. We construct EgoAffordance, a large-scale dataset comprising 204K episodes with 5.6M visual affordances and 11.6M grasp and trajectory affordances. Building on this, we introduce VLAff, a large vision-language model-based unified foundation model that learns cross-modal correlations across all actionable affordances. Given a visual observation and instruction, VLAff generates visual affordance heatmaps, grasp poses, and trajectories, which are then converted into directly executable actions by utilizing 3D scene information. Through extensive experiments, we demonstrate that VLAff not only achieves state-of-the-art performance on visual affordance prediction, but can also be effectively applied to real robot applications such as zero-shot manipulation and affordance-guided robot learning.

cs.RO↗

arXiv2026

WARL: Wrench-Augmented Reinforcement Learning for Task-Agnostic Learning in Legged Robots

While reinforcement learning for legged robots has achieved high motor performance, it has been constrained by the limited exploration capability of actions confined to the joint space. To address this issue, this study proposes a new method, Wrench-Augmented Reinforcement Learning (WARL), which introduces a wrenche (force and torque) into the action space. The proposed method combines wrench-guided exploration with a success rate-based curriculum mechanism to expand exploration capabilities in the early stages of learning, with the ultimate goal of acquiring behaviors based solely on joint control. Experiments using a quadruped robot demonstrated that WARL can learn robustly across diverse terrains and motor tasks without requiring terrain-specific reward adjustments or complex curriculum designs. Furthermore, an ablation study verified the effectiveness of the Switching Curriculum, which gradually eliminates the wrench. On the other hand, we also show that introducing a wrench can encourage behaviors that do not sufficiently exploit the robot's physical embodiment. These findings suggest that while wrench-based exploration enhancement is effective for improving learning efficiency, designing it in a way that is consistent with the robot's physical structure is a critical future challenge.

cs.RO↗

arXiv2026

MEVION: Low-Cost Open-Source Data Collection System for Powerful and High-Speed Dual-Arm Manipulation

The global competition for developing robotic foundation models is intensifying. Among the data collection systems used for dual-arm robots, ALOHA is representative of being low-cost and open-source, and is widely adopted by researchers as a de facto standard. However, due to its limited ability to generate high forces and speeds, it is difficult to handle heavy objects or perform fast manipulations. To address this, we developed MEVION, a low-cost and open-source dual-arm robot data collection system capable of generating greater force and speed. All parts of this robot can be sourced through e-commerce, and by extensively utilizing sheet metal welding, its large body structure is constructed with a small number of components at low cost, while also simplifying assembly. MEVION is equipped with four 6-DoF arms with parallel grippers. Each arm weighs 7.0 kg and has a maximum torque of 60 Nm, and the entire system can be constructed for about USD 14,000. The elbow joint adopts a closed-link mechanism similar to those used in quadruped robots, which reduces the distal mass and enables higher force and speed output at the end-effector. We demonstrate that MEVION enables data collection for object manipulation tasks not previously possible and supports imitation learning-based motion generation. All hardware and software of this work are included in the Supplementary Materials or https://github.com/haraduka/mevion.

cs.RO↗

arXiv2026

Design, Control, and Motion Strategy for DELTA: Transformable Multilink Multirotor for Air-Ground Hybrid Locomotion and Manipulation

In recent years, multimodal locomotion capabilities have enabled robots to maneuver in both terrestrial and aerial domains. However, most of these robots are designed only for locomotion, and few possess the manipulation capabilities required for practical tasks. By adding a manipulator, ground robots can perform manipulation, and some drones with robotic arms have demonstrated aerial manipulation. Nonetheless, such multirotors cannot be directly used for manipulation on the ground, and this configuration itself is unsuitable for air-ground hybrid locomotion. This is because their thruster-centralized structure makes it difficult to achieve both sufficient degrees of freedom (DoF) for manipulation and stable motion with contact and transformation. Therefore, in this work, we develop a new multilink multirotor with thrusters on each link and capable of contact with the environments. This robot can perform terrestrial rolling locomotion, aerial flight locomotion, and manipulation in multiple environments using joint actuation. First, we introduce a minimal configuration design of the proposed robot. We also describe a kinematic model and propose a design for each component based on this model. Second, we propose a real-time control method based on nonlinear optimization that considers contact and joint motion, which can be applied to various multirotors. Third, we propose motion strategies that include contact constraints specific to air-ground hybrid multilink multirotors, and analyze the limitations of manipulation capabilities based on multi-contact model. Finally, we demonstrate a variety of motions in both domains using the implemented prototype. To the best of our knowledge, this is the first demonstration of air-ground hybrid locomotion and manipulation by a multilink multirotor.

cs.RO↗

arXiv2026

WiXus: A Wheeled-Legged Robot with Wire-Driven Environmental Utilizing to Integrate Mobility and Manipulation

Wheeled-legged robots, which have wheels at their feet and achieve high mobility by coordinating wheel drive and leg drive, have been developed. These robots have been developed purely as platforms specialized for locomotion. Therefore, they do not have a means to repurpose their legs for roles other than locomotion, such as object manipulation or tool utilization. In this paper, we address the problem of how to draw out the potential task-execution capability of the legs by freeing them from the roles of locomotion through external body support. To this end, we propose and develop a new robot, WiXus, which fuses a wheeled-legged mechanism with a wire-driven mechanism that utilizes the external environment. The developed WiXus demonstrates not only planar locomotion with wheeled-legged drive, but also three-dimensional mobility such as cliff climbing by coordinating wire-driven and wheeled-legged actuation. Furthermore, by suspending the body with wire-driven actuation, WiXus successfully repurpose its legs as arms to perform object manipulation, (e.g., rescuing a dog (stuffed animal)), and tool utilization (e.g., harvesting an apple (mockup) with loppers). This study demonstrates that the approach of utilizing the environment with wire-driven actuation is a new design principle that extends the operational domain of wheeled-legged robots.

cs.RO↗

arXiv2026

Self-assembling Modular Aerial Robot for Versatile Aerial Tasks

Multirotor aerial robots excel at maneuvering in three-dimensional space, and recent advances enable nimble navigation in cluttered and confined environments, especially for small airframes. By contrast, platforms built for high-altitude work tend to be larger to deliver high thrust for stable physical interaction with the environment. However, these conflicting design requirements create a long-standing trade-off between nimble navigation and robust aerial manipulation. Here, we present LEGION units, which are reconfigurable modular aerial robots capable of in-flight self-assembly for cooperative manipulation, drawing inspiration from the self-organized collectives formed by ants. Each unit retains nimble maneuverability while joint-equipped docking interfaces at both ends enable end-to-end self-assembly into a flying manipulator. We show that multiple units autonomously dock in flight; once latched, they maintain a zero-clearance interlock by controlling the contact force and torque, enabling reliable aggregation and articulated motion even outdoors. We further show that self-reconfigurability enables morphological switching between nimble individual flight and collective articulated manipulation, while realizing core in-flight manipulation primitives including pushing, pulling, rotating, grasping, and carrying. LEGION's self-organization enables aerial robots, especially in swarms, to shift from passive observers to active participants in their environment, broadening the scope of aerial physical interaction.

cs.RO↗

arXiv2026

EFGCL: Learning Dynamic Motion through Spotting-Inspired External Force Guided Curriculum Learning

Learning dynamic whole-body motions for legged robots through reinforcement learning (RL) remains challenging due to the high risk of failure, which makes efficient exploration difficult and often leads to unstable learning. In this paper, we propose External Force Guided Curriculum Learning (EFGCL), a guided RL approach based on the principle of physical guidance, in which external assistive forces are introduced during training. Inspired by spotting in artistic gymnastics, EFGCL enables agents to physically experience successful motion executions without relying on task-specific reward shaping or reference trajectories. Experiments on a quadrupedal robot performing Jump, Backflip, and Lateral-Flip tasks demonstrate that EFGCL accelerates learning of the Jump task by approximately a factor of two and enables the acquisition of complex whole body motions that conventional RL methods fail to learn. We further show that the learned policies can be deployed on real robot, reproducing motions consistent with those observed in simulation. These results indicate that physically guided exploration, which allows agents to experience success early in training, is an effective and general strategy for improving learning efficiency in dynamic whole-body motion tasks.

cs.RO↗

arXiv2026

Exploring the proprioceptive potential of joint receptors using a biomimetic robotic joint

In neuroscience, joint receptors have traditionally been viewed as limit detectors, providing positional information only at extreme joint angles, while muscle spindles are considered the primary sensors of joint angle position. However, joint receptors are widely distributed throughout the joint capsule, and their full role in proprioception remains unclear. In this study, we specifically focused on mimicking Type I joint receptors, which respond to slow and sustained movements, and quantified their proprioceptive potential using a biomimetic joint developed with robotics technology. Results showed that Type I-like joint receptors alone enabled proprioceptive sensing with an average error of less than 2 degrees in both bending and twisting motions. These findings suggest that joint receptors may play a greater role in proprioception than previously recognized and that the relative contributions of muscle spindles and joint receptors are differentially weighted within neural networks during development and evolution. Furthermore, this work may prompt new discussions on the differential proprioceptive deficits observed between the elbows and knees in patients with hereditary sensory and autonomic neuropathy type III. Together, these findings highlight the potential of biomimetics-based robotic approaches for advancing interdisciplinary research bridging neuroscience, medicine, and robotics.

cs.RO↗