arXiv subjects

Juejun Hu

Publications and source records attributed to Juejun Hu.

At least 19 recordsLinked to original sources

arXiv2026

Grammar-based topology search for reconfigurable integrated photonic spectrometers

Reconfigurable integrated photonic spectrometers can generate exponentially increasing measurement states from a small number of switching elements, making them a promising design class for high-performance portable spectroscopy. However, selecting a circuit architecture remains largely intuition driven. We introduce a grammar-based topology optimization framework that composes standard photonic building blocks, canonicalizes and physically prunes candidate circuits, and jointly searches topology and component parameters using a coherent scattering-matrix model. Designs are screened by a decoder-independent architecture objective that combines absolute singular-value noise gain with multi-line conditioning, thereby accounting for response diversity and optical throughput. Direct held-out spectrum reconstruction confirms that this surrogate is a strong predictor of reconstruction quality at high incident signal-to-noise ratio (SNR). Across the nonresonant and resonator-augmented design spaces examined, dFT and its variants offer the best balanced performance; increased component loss favors a shallower dFT variant in which one differential-delay stage is replaced by an analog optical phase shifter. Passive and active rings provide no robust advantage attributable to resonant amplitude coding. The results identify balanced complementary interferometric responses, efficient terminal collection, and limited lossy circuit depth as central design rules, and establish a systematic route for selecting task-optimized photonic circuit topologies under technology-specific constraints.

physics.optics↗

arXiv2026

Nanophotonic control of spatial information in scintillation detectors

X-rays enable non-invasive imaging across medicine, security, materials science, and beyond, yet modern systems remain constrained by the need to resolve finer structures at lower radiation dose. Scintillators are the dominant materials for detecting X-rays, but face a longstanding compromise: thick scintillators absorb X-rays effectively, whereas optical photons generated throughout their volume spread before detection, degrading spatial information. Existing scintillator architectures largely try to preserve resolution by physically confining light using pixels, columnar crystals, or microstructured channels. Here, we show that high-resolution detection does not require the volumetric confinement of scintillation light. A metalens integrated directly with a bulk scintillator uses nanophotonic wavefront control to preferentially transfer high-spatial-frequency information from volumetrically generated scintillation light to the detector, while retaining the X-ray absorption of a thick scintillator. We experimentally recover fine spatial detail in X-ray images of inorganic and biological specimens. In a detector geometry relevant to computed tomography (CT), the experimentally validated model predicts a fivefold reduction in required X-ray dose and a 25-fold increase in resolution bandwidth relative to a state-of-the-art pixelated scintillator. These results establish wavefront engineering as a route to separating efficient X-ray absorption from optical image formation, with the potential for substantially higher-resolution, lower-dose CT.

physics.optics↗

arXiv2026

Dosimetric characterization of a nanophotonic scintillator and applications to real-time in-vivo total body irradiation dosimetry

Purpose: Recent advances in metasurface photonics and manufacturing have enabled a nanophotonic surface coating to be applied to conventional scintillators, which has been shown to significantly improve light yield. However, the dosimetric properties of such coatings has not been established. We performed the first dosimetric characterization of a nanophotonic scintillator and explored clinical application to real-time in-vivo total body irradiation (TBI) dosimetry. Methods: A 4.5x1.5 cm cerium-doped yttrium aluminum garnet (YAG:Ce) scintillator, half patterned with the nanophotonic structure, half left unpatterned, enabled direct comparison between conventional and nanophotonic surfaces. The scintillator was placed in a 3D-printed light-tight box with an off-axis CMOS camera and irradiated with a clinical linear accelerator. Absolute dosimetry was done with dose-calibrated radiochromic film. For TBI, the scintillator was positioned on an anthropomorphic phantom in a TBI booth, with signal measured by both CMOS and consumer-grade phone cameras under different room lighting conditions. Results: The nanophotonic scintillator showed a 4.1x increase in signal and a 3.7x increase in contrast-to-noise ratio versus the conventional scintillator. Both scintillators exhibited dose-rate independence and linear dose response, with modest energy dependence. For TBI, the nanophotonic scintillator produced a clearly detectable signal with both CMOS and phone cameras, whereas the conventional scintillator signal was undetectable. Conclusions: Nanophotonic structures significantly enhance light output of conventional scintillators without impacting their dosimetric properties. Nanophotonic scintillators may enable real-time in-vivo TBI dosimetry. Future work should investigate this technology for improved dosimetry equipment and X-ray imaging detectors.

physics.med-ph↗

arXiv2026

Inverse designed resistive heaters for uniform switching of Phase Change Materials

Non-volatile phase-change material (PCM)-integrated metasurfaces offer a promising pathway toward next-generation solid-state reconfigurable free-space optics. However, their practical operation is currently bottlenecked by the highly non-uniform thermal profiles generated by the external heaters used to switch the PCM between its amorphous and crystalline states. The non-uniform heat profile in turn severely restricts the active switching area of the PCM integrated devices. In this work, we present an inverse-designed doped silicon resistive heater on a silicon-on-sapphire platform, featuring a spatially varying doping profile explicitly tailored to generate uniform heat. The new heater significantly improves spatial temperature uniformity, reducing the thermal gradient from 110 K in the case of typical conventional heater to merely 25 K in the case of the inverse-designed heater at a target temperature of ~1000 K. By meticulously optimizing the doping and annealing processes to suppress lateral dopant diffusion, we achieve a near-perfect spatial doping resolution capable of patterning two distinct doped Silicon filaments just 100 nm apart. We experimentally fabricate these devices and demonstrate their efficacy by successfully switching a large area (~18 x 14 micrometer square) of the wide-bandgap phase-change material (PCM) Sb2S3 using a compact heater geometry of size 26 x 26 micrometer square. We show that our inverse-designed heater achieves a 10-fold increase in active PCM switching area despite a reduction in the total heater footprint when compared to a conventional heater. Ultimately, this work provides a crucial steppingstone toward the development of non-volatile PCM-based reconfigurable free-space optics.

physics.optics↗

arXiv2026

Ultrawide-angle diffraction-limited 2D beam steering via hybrid integrated metasurface-photonic circuit

Two-dimensional (2D) wide field-of-view (FOV) beam steering is a key enabling capability for emerging free-space optical systems, including inter-satellite optical links, airborne LiDAR, point-to-point optical wireless communications, and collaborative robotic platforms. These applications require rapid acquisition and tracking across both azimuth and elevation; architectures that offer wide scanning in only one dimension while maintaining limited coverage in the orthogonal direction constrain link availability, coverage uniformity, and system agility. Here, we demonstrate a chip-scale platform for ultrawide-angle, diffraction-limited 2D beam steering based on hybrid integration of a silicon photonic integrated circuit (PIC) and an optical metasurface. A free-form micro-optical reflector efficiently transforms the guided waveguide mode into an expanded free-space beam that illuminates an analytically optimized ultrawide-FOV metasurface. The integrated system achieves a measured FOV exceeding 160{\deg} while maintaining diffraction-limited beam quality over a broad angular range at telecom wavelengths. This hybrid PIC-metasurface architecture provides a compact and scalable route to high-quality 2D beam steering and establishes a practical pathway toward integrated optical projectors for space-based optical communications and other applications requiring agile, wide-angle, high-fidelity beam control.

physics.optics↗

arXiv2026

Increased endurance of nonvolatile photonics enabled by nanostructured phase-change materials

The rapid rise of artificial intelligence, and in-memory computing has reinvigorated research on scalable, energy-efficient, and reconfigurable photonic hardware. Non-volatile phase-change materials (PCMs) are attractive, as they offer large refractive index contrast, wavelength-scale footprints, and zero static power consumption. However, current PCM-based electrically controlled photonic devices are plagued by high insertion loss and low endurance. One prevalent hypothesis for these material limitations come from electromagnetic scattering in the interface and large programming volumes, respectively. Here, we validate this hypothesis by showing that nano-structuring of PCM minimizes optical loss and enhances the endurance. By tapering both ends of a wide bandgap PCM Sb2Se3 segment on a silicon waveguide, we suppressed the insertion loss by ~94% (resulting in a loss of ~0.1 dB per {\pi} phase shift). Through combining tapering and segmentation, we achieved high optical modulation amplitude (~70%), low loss (~0.5 dB per {\pi} phase shift), low-voltage (< 5V) actuation, and record high endurance greater than 100 million cycles. This work showcases the substantial advantage of nanopatterning PCMs to attain low loss and high cyclability.

physics.optics↗

arXiv2026

Wavefront Engineering for Scintillation-Based Imaging

Recent research in nanophotonics for scintillation-based imaging has demonstrated promising improvements in scintillator performance. In parallel, advances in nanophotonics have enabled wavefront control through metasurfaces, a capability that has transformed fields such as microscopy by allowing tailored control of optical propagation. This naturally raises the following question, which we address in this perspective: can wavefront-control strategies be leveraged to improve scintillation-based imaging? To answer this question, we explore nanophotonic- and metasurface-enabled wavefront control in scintillators to mitigate image blurring arising from their intrinsically diffuse light emission. While depth-of-field extension in scintillation faces fundamental limitations absent in microscopy, this approach reveals promising avenues, including stacked scintillators, selective spatial-frequency enhancement, and X-ray energy-dependent imaging. These results clarify the key distinctions in adapting wavefront engineering to scintillation and its potential to enable tailored detection strategies.

physics.optics↗

arXiv2025

Wide field-of-view and large depth-of-field metalenses

The ability to visualize both macroscopic and microscopic features over an extended field of view is essential for endoscopic imaging and other applications ranging from machine vision to microscopy. However, miniaturizing endoscopes introduces inherent trade-offs between size and optical performance, including field-of-view (FOV), depth-of-field (DOF), and resolution. These constraints limit the use of microendoscopes in clinical settings such as early cancer detection within narrow, hard-to-access anatomical regions, including the lung, ovaries, and pancreas. State-of-the-art microendoscopes typically rely on microlens assemblies that increase both cost and size. Their large f-numbers also hinder the collection of high-resolution information from live tissue. In this work, we present two compact metalens designs that provide wide FOV, extended DOF, and high resolution, enabled by custom-tailored point spread functions (PSFs). The devices achieve a full 172 degrees FOV, an extended DOF from 0.4 mm to beyond 300 mm, and a resolution of 30 line pairs per millimeter, all within a 1 mm x 1 mm x 0.2 mm footprint. A key advantage of our approach is the ability to transition seamlessly between low and high magnification without mechanical refocusing. Final images are reconstructed through backend deconvolution, highlighting the potential of hybrid imaging systems that integrate computational techniques with flat-optics components.

physics.optics↗

arXiv2025

Wafer-scale conformal metasurface optics

Curved and conformal optics offer significant advantages by unlocking additional geometric degrees of freedom for optical design. These capabilities enable enhanced optical performance and are essential for meeting non-optical constraints, such as those imposed by ergonomics, aerodynamics, or wearability. However, existing fabrication techniques such as direct electron or laser beam writing on curved substrates, and soft-stamp-based transfer or nanoimprint lithography suffer from limitations in scalability, yield, geometry control, and alignment accuracy. Here, we present a scalable fabrication strategy for curved and conformal metasurface optics leveraging thermoforming, an industry-standard, high-throughput manufacturing process widely used for shaping thermoplastics. Our approach uniquely enables wafer-scale production of highly curved metasurface optics, achieving sub-millimeter radii of curvature and micron-level alignment precision. To guide the design and fabrication process, we developed a thermorheological model that accurately predicts and compensates for the large strains induced during thermoforming. This allows for precise control of metasurface geometry and preservation of optical function, yielding devices with diffraction-limited performance. As a demonstration, we implemented an artificial compound eye comprising freeform micro-metalens arrays. Compared to traditional micro-optical counterparts, the device exhibits an expanded field of view, reduced aberrations, and improved uniformity, highlighting the potential of thermoformed metasurfaces for next-generation optical systems.

physics.optics↗

arXiv2025

2D Addressable Mid-infrared Metasurface Spatial Light Modulator

Active metasurfaces enable dynamic control of light for applications in beam steering, pixelated holography, and adaptive optics, but demonstrations of two-dimensional (2D) electrically addressable arrays have so far been limited. Here we introduce a scalable 2D architecture based on phase-change materials (PCMs) integrated metasurfaces and apply it to realize the first transmissive mid-infrared (mid-IR) spatial light modulator (SLM). The device is fabricated through standard silicon photonic foundry processing combined with backend-of-line (BEOL) integration and employs multilayer backend metal interconnects to implement a crossbar addressing scheme. Each pixel is integrated with a silicon diode selector to suppress sneak-path currents, a feature essential for scaling to large arrays. The result establishes a foundry-compatible route to high-density, large-area active metasurfaces with independently tunable pixels.

physics.optics↗

arXiv2025

Coherent all-optical tuning of large-area phase-gradient metasurface

Tunable active metasurfaces have become a major research focus in recent years. Among tuning mechanisms, all-optical coherent control stands out because it requires no material or geometric change, enabling ultrafast, low-energy, interference-based modulation of amplitude, phase, and polarization in ultrathin devices. However, when applied to phase-gradient metasurfaces, coherent control has been limited to small apertures effectively confined to a single Fresnel zone, leading to large divergence and degraded beam quality. Here we propose and numerically validate a scalable method that enables large-area coherent control. The key idea is to use coherent illumination to tune the phase gradient within each Fresnel zone while a direct search algorithm optimizes zone-by-zone parameters to meet system-level targets. Using this principle, we demonstrate continuous tuning of a large-area metasurface for continuous beam-steering without per-meta-atom phase actuation. The same framework applies broadly to continuously tunable phase-gradient optics, including varifocal metalenses, parfocal zoom metalenses, tunable axicons, and related dynamic focusing elements.

physics.optics↗

arXiv2025

Incorporating Si into Sb2Se3: Tailoring Optical Phase Change Materials via Nanocomposites

Chalcogenide-based optical phase change materials (OPCMs) exhibit a large contrast in refractive index when reversibly switched between their stable amorphous and crystalline states. OPCMs have rapidly gained attention due to their versatility as nonvolatile amplitude or phase modulators in various photonic devices. However, open challenges remain, such as achieving reliable response and transparency spanning into the visible spectrum, a combination of properties in which current broadband OPCMs (e.g., Ge2Sb2Se4Te1, Sb2Se3, or Sb2S3) fall short. Discovering novel materials or engineering existing ones is, therefore, crucial in extending the application scope of OPCMs. Here, we use magnetron co-sputtering to study the effects of Si doping into Sb2Se3. We employ ellipsometry, X-ray diffraction, Raman spectroscopy, and scanning and transmission electron microscopy to investigate the effects of Si doping on the optical properties and crystal structure and compare these results with those from first principles calculations. Moreover, we study the crystallization and melt-quenching of thin films via nano-differential scanning calorimetry (NanoDSC). Our experiments demonstrate that 20% Si doping increases the transparency window in both states, specifically to 800 nm (1.55 eV) in the amorphous phase, while reducing power consumption by lowering the melting temperature. However, this reduction comes at the cost of reducing the refractive index contrast between states and slowing the kinetics of the phase transition.

cond-mat.mtrl-sci↗

arXiv2025

Electrically reconfigurable nonvolatile transmissive metasurface in visible

The synergy between metasurfaces and non-volatile phase change materials (PCMs) has created many reconfigurable photonic devices for applications in optical memory, optical computing and optical communications. But these advances have been limited to the infrared wavelengths due to the high loss of PCMs in the visible regime. Here we demonstrate a nonvolatile visible metasurface that is electrically reconfigurable using wide bandgap PCM Sb2S3. Our device supports a resonant mode at 610 nm, a wavelength largely under-explored for PCM-based metasurfaces. By incorporating only a 20 nm thick layer of Sb2S3, we experimentally demonstrate a resonance tuning range of 16 nm. Reversible switching of the metasurface is accomplished in situ using a carefully engineered, ultrathin doped silicon micro-heater. Our work paves the way for integrating PCMs into visible-frequency systems, particularly for human-centric applications such as augmented and virtual reality displays.

physics.optics↗

arXiv2025

Roadmap on Neuromorphic Photonics

This roadmap consolidates recent advances while exploring emerging applications, reflecting the remarkable diversity of hardware platforms, neuromorphic concepts, and implementation philosophies reported in the field. It emphasizes the critical role of cross-disciplinary collaboration in this rapidly evolving field.

cs.ET↗

arXiv2024

Large-scale self-assembled nanophotonic scintillators for X-ray imaging

Scintillators are essential for converting X-ray energy into visible light in imaging technologies. Their widespread application in imaging technologies has been enabled by scalable, high-quality, and affordable manufacturing methods. Nanophotonic scintillators, which feature nanostructures at the scale of their emission wavelength, provide a promising approach to enhance emission properties like light yield, decay time, and directionality. However, scalable fabrication of such nanostructured scintillators has been a significant challenge, impeding their widespread adoption. Here, we present a scalable fabrication method for large-area nanophotonic scintillators based on the self-assembly of chalcogenide glass photonic crystals. This technique enables the production of nanophotonic scintillators over wafer-scale areas, achieving a six-fold enhancement in light yield compared to unpatterned scintillators. We demonstrate this approach using a conventional X-ray scintillator material, cerium-doped yttrium aluminum garnet (YAG:Ce). By analyzing the influence of surface nanofabrication disorder, we establish its effect on imaging performance and provide a route towards large-scale scintillation enhancements without decrease in spatial resolution. Finally, we demonstrate the practical applicability of our nanophotonic scintillators through X-ray imaging of biological and inorganic specimens. Our results indicate that this scalable fabrication technique could enable the industrial implementation of a new generation of nanophotonic-enhanced scintillators, with significant implications for advancements in medical imaging, security screening, and nondestructive testing.

physics.optics↗

arXiv2024

Unravelling and circumventing failure mechanisms in chalcogenide optical phase change materials

Chalcogenide optical phase change materials (PCMs) have garnered significant interest for their growing applications in programmable photonics, optical analog computing, active metasurfaces, and beyond. Limited endurance or cycling lifetime is however increasingly becoming a bottleneck toward their practical deployment for these applications. To address this issue, we performed a systematic study elucidating the cycling failure mechanisms of Ge$_2$Sb$_2$Se$_4$Te (GSST), a common optical PCM tailored for infrared photonic applications, in an electrothermal switching configuration commensurate with their applications in on-chip photonic devices. We further propose a set of design rules building on insights into the failure mechanisms, and successfully implemented them to boost the endurance of the GSST device to over 67,000 cycles.

physics.optics↗

arXiv2024

Thermal Inverse design for resistive micro-heaters

This paper proposes an inverse design scheme for resistive heaters. By adjusting the spatial distribution of a binary electrical resistivity map, the scheme enables objective-driven optimization of heaters to achieve pre-defined steady-state temperature profiles. The approach can be fully automated and is computationally efficient since it does not entail extensive iterative simulations of the entire heater structure. The design scheme offers a powerful solution for resistive heater device engineering in applications spanning electronics, photonics, and microelectromechanical systems.

physics.app-ph↗

arXiv2024

Electrically Tuning Quasi-Bound States in the Continuum with Hybrid Graphene-Silicon Metasurfaces

Metasurfaces have become one of the most prominent research topics in the field of optics owing to their unprecedented properties and novel applications on an ultrathin platform. By combining graphene with metasurfaces, electrical tunable functions can be achieved with fast tuning speed, large modulation depth and broad tuning range. However, the tuning efficiency of hybrid graphene metasurfaces within the short-wavelength infrared (SWIR) spectrum is typically low because of the small resonance wavelength shift in this wavelength range. In this work, through the integration of graphene and silicon metasurfaces that support quasi-bound states in the continuum (quasi-BIC), we experimentally demonstrate significant transmittance tuning even with less than 30 nm resonance wavelength shift thanks to the high quality-factor of quasi-BIC metasurfaces. The tunable transmittance spectrum was measured using Fourier Transform Infrared Spectroscopy (FTIR) with a modified reflective lens to improve the accuracy, and the electrical tuning was realized utilizing the cut-and-stick method of ion gel. At the wavelength of 3.0 um, the measured change of transmittance T_max-T_min and modulation depth (T_max-T_min)/T_max can reach 22.2% and 28.9%, respectively, under a small bias voltage ranging from -2 V to +2 V. To the best of our knowledge, this work is the first experimental demonstration of tunable graphene/quasi-BIC metasurfaces, which have potential applications in optical modulation, reconfigurable photonic devices, and optical communications.

physics.optics↗