arXiv subjects

Jeongdo Ahn

Publications and source records attributed to Jeongdo Ahn.

3 recordsLinked to original sources

arXiv2026

Design of a Fully Actuated 4-DOF Robotic Finger With Joint-Specific Hybrid Remote Actuation

This paper presents a fully actuated 4-DOF robotic finger using a joint-specific hybrid remote-actuation architecture. The metacarpophalangeal (MCP) joint is driven by two coordinated rigid-link transmission sets, whereas the proximal interphalangeal (PIP) and distal interphalangeal (DIP) joints are independently actuated by closed-loop wire transmissions incorporating circular rolling-contact joints (RCJs). A larger transmission radius is used at the PIP joint than at the DIP joint. The RCJ wire geometry maintains the total wire-loop length during joint rotation, and the DIP wire routing is designed so that PIP motion does not affect its differential actuation for a fixed MCP configuration. The distal wire transmission, MCP linkage, and fingertip kinematics are analytically modeled. In experiments, the transmission behavior was quantitatively evaluated from the ball-screw displacements measured using ArUco-marker tracking. MCP actuation produced measurable displacements of the PIP and DIP transmission units, whereas isolated PIP and DIP actuation with the MCP fixed supported the intended mechanical decoupling between the distal transmissions. The mean peak fingertip forces under isolated MCP, PIP, and DIP actuation were 21.28 N, 9.22 N, and 5.75 N, respectively. The resulting finger postures were also examined using objects of different geometries and sizes.

cs.RO↗

arXiv2026

Combinatorial Optimization of Robotic Hand Kinematic Structures Using a Potential-Dexterity-Based QUBO Formulation

Robotic hand kinematic design involves combinatorial selection among multiple finger structures whose performance depends on both individual kinematic characteristics and inter-finger interactions. This study presents a potential-dexterity-based quadratic unconstrained binary optimization (QUBO) formulation for combinatorial optimization of robotic hand kinematic structures. Potential dexterity-related metrics were evaluated through kinematic analysis and encoded into a 27-variable QUBO problem incorporating individual finger performance, thumb-to-finger workspace-overlap interactions, one-hot selection constraints, and pairwise structural compatibility. Exhaustive evaluation of the design space established a reference optimum and enabled direct validation of the formulated objective. Discretization sensitivity analysis showed that the selected design remained unchanged across the tested joint-space sampling intervals and at a finer workspace voxel resolution, while sensitivity was observed under coarse voxelization. Simulated annealing consistently recovered the reference optimum at higher sampling counts, and direct execution on D-Wave quantum annealing hardware also recovered the reference optimum under all tested sampling conditions. These results demonstrate that the proposed formulation provides a common QUBO representation for constrained robotic hand kinematic structure selection and enables evaluation using exhaustive, classical annealing, and quantum annealing approaches.

cs.RO↗

arXiv2026

Kinematic Optimization of Phalanx Length Ratios in Robotic Hands Using Potential Dexterity

In the design stage of robotic hands, it is not straightforward to quantitatively evaluate the effect of phalanx length ratios on dexterity without defining specific objects or manipulation tasks. Therefore, this study presents a framework for optimizing the phalanx length ratios of a five-finger robotic hand based on potential dexterity within a kinematic structure. The proposed method employs global manipulability, workspace volume, overlap workspace volume, and fingertip sensitivity as evaluation metrics, and identifies optimal design configurations using a weighted objective function under given constraints. The reachable workspace is discretized using a voxel-based representation, and joint motions are discretized at uniform intervals for evaluation. The optimization is performed over design sets for both the thumb and the other fingers, and design combinations that do not generate overlap workspace are excluded. The results show that each phalanx does not contribute equally to the overall dexterity, and the factors influencing each phalanx are identified. In addition, it is observed that the selection of weighting coefficients does not necessarily lead to the direct maximization of individual performance metrics, due to the non-uniform distribution of evaluation measures within the design space. The proposed framework provides a systematic approach to analyze the trade-offs among reachability, dexterity, and controllability, and can serve as a practical guideline for the kinematic design of multi-fingered robotic hands.

cs.RO↗