arXiv subjects

Helmut Soltner

Publications and source records attributed to Helmut Soltner.

12 recordsLinked to original sources

arXiv2026

Openable Force-Balanced Halbach Magnets: From Fibonacci Sphere Simulations to Icosahedral Realizations

A long-standing goal in magnet design is to completely surround a volume of highly homogeneous magnetic field with permanent magnets while maintaining practical access to that volume. In this work, we present a theoretical and experimental investigation of mechanically accessible spherical magnets in Halbach configuration that can be opened with minimal or vanishing force. Focusing on dipolar Halbach spheres composed of discrete magnetic subunits, we derive conditions for force-free opening along specific cutting planes. These conditions define a continuous set of geometries for which tensile magnetic forces cancel, leaving only shear components, enabling mechanically effortless opening. The theoretical predictions are validated experimentally using icosahedral approximations of the Halbach sphere, for which both opening forces and magnetic field properties are measured. The results demonstrate that excellent field homogeneity can be preserved while reducing opening forces by orders of magnitude. Although discussed in detail for the dipolar case, the theoretical framework is general and applicable to higher-order multipole Halbach systems. Finally, the concepts are extended to spherocylindrical Halbach configurations, highlighting their potential for large-volume, highly homogeneous, and mechanically accessible permanent-magnet systems for magnetic resonance

physics.ins-det↗

arXiv2025

Distributed Current Injection into a One-Dimensional Ballistic Edge Channel

We generalize Landauer's theory of ballistic transport in a one-dimensional (1D) conductor to situations where charge carrier injection and extraction are not any more confined to electrodes at either end of the channel, but may occur along its whole length. This type of distributed injection is expected to occur from the two-dimensional (2D) bulk of, e.g., a quantum spin (or anomalous) Hall insulator to its topologically protected edge states. We apply our conceptual solution to the case of two metal electrodes contacting the 2D bulk, enabling us to derive criteria that discriminate ballistic from resistive edge channels in multi-terminal transport experiments.

cond-mat.mes-hall↗

arXiv2024

Compact beam position monitor using a segmented toroidal coil

A new, compact beam position monitor based on segmented a toroidal coil surrounding the charged particle beam has been investigated. It makes use of the induced voltages in the windings instead of the induced charge imbalance on capacitor plates in the conventional beam position monitors. We theoretically investigate the response of the coils to the bunched particle beam based on a lumped element model and compare it with measurements in the laboratory and in the storage ring COSY, in terms of beam displacement. As to the frequency response of the coils, we find a resonant behavior, which may be exploited to increase the sensitivity of the device further. The resolution presently achieved is about 5 micrometer in a one second time interval for a beam current of 0.5 mA.

physics.acc-ph↗

arXiv2024

Theoretical development of a new spin filter generation

Since the early days of quantum mechanics hydrogen, as the simplest of all atoms, has been studied or used to investigate new physics. In parallel, this knowledge leads to different applications, e.g. a spin filter to separate metastable hydrogen atoms in single hyperfine substates with electron spin m_s=1/2. Subsequently, this work provides the necessary theory as well as experimental conditions to build a new generation of spin filter which permits the separation of all four individual metastable hydrogen hyperfine states as well as for its isotopes in a corresponding beam.

physics.atom-ph↗

arXiv2023

Preservation of $^3\mkern-2mu$He ion polarization after laser-plasma acceleration

The preservation of nuclear spin alignment in plasmas is a prerequisite for important applications, such as energy production through polarized fusion or the acceleration of polarized particle beams. Although this conservation property has been the basis of numerous theoretical papers, it has never been experimentally confirmed. Here, we report on first experimental data from a polarized $^3\mkern-2mu$He target heated by a PW laser pulse, showing evidence for persistence of the nuclear polarization after acceleration to MeV energies. The finding also validates the concept of using pre-polarized targets for experiments at high-power laser facilities.

physics.plasm-ph↗

arXiv2023

Practical Concepts for Design, Construction and Application of Halbach Magnets in Magnetic Resonance

This review is a compilation of relevant concepts in designing Halbach multipoles for magnetic resonance applications. The main focus is on providing practical guidelines to plan, design and build such magnets. Therefore, analytical equations are presented for estimating the magnetic field from ideal to realistic systems. Various strategies of homogenizing magnetic fields are discussed together with concepts of opening such magnets without force, or combining them for variable fields. Temperature compensation and other practical aspects are also reviewed. For magnetic resonance two polarities (di- and quadrupole) are of main interest, but higher polarities are also included.

physics.ins-det↗

arXiv2022

How cold is the junction of a millikelvin scanning tunnelling microscope?

We employ a scanning tunnelling microscope (STM) cooled to millikelvin temperatures by an adiabatic demagnetization refrigerator (ADR) to perform scanning tunnelling spectroscopy (STS) on an atomically clean surface of Al(100) in a superconducting state using normal-metal and superconducting STM tips. Varying the ADR temperatures between 30 mK and 1.2 K, we show that the temperature of the STM junction $T$ is decoupled from the temperature of the surrounding environment $T_{\mathrm{env}}$. Simulating the STS data with the $P(E)$ theory, we determine that $T_{\mathrm{env}} \approx 1.5$ K, while the fitting of the superconducting gap spectrum yields the lowest $T=77$ mK.

cond-mat.mes-hall↗

arXiv2022

First Search for Axion-Like Particles in a Storage Ring Using a Polarized Deuteron Beam

Based on the notion that the local dark-matter field of axions or axion-like particles (ALPs) in our Galaxy induces oscillating couplings to the spins of nucleons and nuclei (via the electric dipole moment of the latter and/or the paramagnetic axion-wind effect), we establish the feasibility of a new method to search for ALPs in storage rings. Based on previous work that allows us to maintain the in-plane polarization of a stored deuteron beam for a few hundred seconds, we performed a first proof-of-principle experiment at the Cooler Synchrotron COSY to scan momenta near 970 MeV/c. This entailed a scan of the spin precession frequency. At resonance between the spin precession frequency of deuterons and the ALP-induced EDM oscillation frequency there will be an accumulation of the polarization component out of the ring plane. Since the axion frequency is unknown, the momentum of the beam and consequently the spin precession frequency were ramped to search for a vertical polarization change that would occur when the resonance is crossed. At COSY, four beam bunches with different polarization directions were used to make sure that no resonance was missed because of the unknown relative phase between the polarization precession and the axion/ALP field. A frequency window of 1.5-kHz width around the spin precession frequency of 121 kHz was scanned. We describe the experimental procedure and a test of the methodology with the help of a radiofrequency Wien filter located on the COSY ring. No ALP resonance was observed. As a consequence an upper limit of the oscillating EDM component of the deuteron as well as its axion coupling constants are provided.

hep-ex↗

arXiv2022

Probing edge state conductance in ultra-thin topological insulator films

Quantum spin Hall (QSH) insulators have unique electronic properties, comprising a band gap in their two-dimensional interior and one-dimensional spin-polarized edge states in which current flows ballistically. In scanning tunneling microscopy (STM), the edge states manifest themselves as a localized density of states. However, there is a significant research gap between the observation of edge states in nanoscale spectroscopy, and the detection of ballistic transport in edge channels which typically relies on transport experiments with microscale lithographic contacts. Here, we study few-layer films of the three-dimensional topological insulator (Bi$_{x}$Sb$_{1-x})_2$Te$_3$, for which a topological transition to a two-dimensional topological QSH insulator phase has been proposed. Indeed, an edge state in the local density of states is observed within the band gap. Yet, in nanoscale transport experiments with a four-tip STM, 2 and 3 quintuple layer films do not exhibit a ballistic conductance in the edge channels. This demonstrates that the detection of edge states in spectroscopy can be misleading with regard to the identification of a QSH phase. In contrast, nanoscale multi-tip transport experiments are a robust method for effectively pinpointing ballistic edge channels, as opposed to trivial edge states, in quantum materials.

cond-mat.mes-hall↗

arXiv2020

Development of a multi-channel power supply for silicon photo-multipliers used with inorganic scintillators

The motivation of the current R&D project is based upon the requirements of the JEDI international collaboration aiming to measure Electric Dipole Moments (EDMs) of charged particles in storage rings. One of the most important elements of such an experiment will be a specially designed polarimeter with the detection system based on a modular inorganic scintillator (LYSO crystal) calorimeter. The calorimeter modules are read out by Silicon Photo Multipliers (SiPMs). This paper describes the development of a multi-channel power supply for the polarimeter modules, providing very stable and clean bias voltages for SiPMs. In order to ensure the best possible performance of SiPMs in conjunction with the crystal-based calorimeter modules and to guarantee the required level of calorimeter stability, several quality requirements have to be met by the power supply. Additionally, it is required to provide features including remote control via the network, ramping of the output voltage, measuring and sending the information about its output voltages and currents, etc. The obtained results demonstrate that the goals for the JEDI polarimeter are met. The developed hardware will be useful in other fields of fundamental and applied research, medical diagnostic techniques and industry, where SiPMs are used.

physics.ins-det↗

arXiv2016

Surface Conductivity of Si(100) and Ge(100) Surfaces Determined from Four-Point Transport Measurements Using an Analytical N-Layer Conductance Model

An analytical N-layer model for charge transport close to a surface is derived from the solution of Poisson's equation and used to describe distance-dependent electrical four-point measurements on the microscale. As the N-layer model comprises a surface channel, multiple intermediate layers and a semi-infinite bulk, it can be applied to semiconductors in combination with a calculation of the near-surface band-bending to model very precisely the measured four-point resistance on the surface of a specific sample and to extract a value for the surface conductivity. For describing four-point measurements on sample geometries with mixed 2D-3D conduction channels often a very simple parallel-circuit model has so far been used in the literature, but the application of this model is limited, as there are already significant deviations, when it is compared to the lowest possible case of the N-layer model, i.e. the 3-layer model. Furthermore, the N-layer model is applied to published distance-dependent four-point resistance measurements obtained with a multi-tip scanning tunneling microscope (STM) on Germanium(100) and Silicon(100) with different bulk doping concentrations resulting in the determination of values for the surface conductivities of these materials.

cond-mat.mes-hall↗

arXiv2015

Surface and Step Conductivities on Si(111) Surfaces

Four-point measurements using a multi-tip scanning tunneling microscope (STM) are carried out in order to determine surface and step conductivities on Si(111) surfaces. In a first step, distance-dependent four-point measurements in the linear configuration are used in combination with an analytical three-layer model for charge transport to disentangle the 2D surface conductivity from non-surface contributions. A termination of the Si(111) surface with either Bi or H results in the two limiting cases of a pure 2D or 3D conductance, respectively. In order to further disentangle the surface conductivity of the step-free surface from the contribution due to atomic steps, a square four-probe configuration is applied as function of the rotation angle. In total this combined approach leads to an atomic step conductivity of $\sigma_\mathrm{step} = (29 \pm 9)$ $\mathrm{\Omega}^{-1} \mathrm{m}^{-1}$ and to a step-free surface conductivity of $\sigma_\mathrm{surf} = (9 \pm 2) \cdot 10^{-6}\,\mathrm{\Omega}^{-1}/\square$ for the Si(111)-(7$\times$7) surface.

cond-mat.mes-hall↗