arXiv ScienceSearch

arXiv subjects

Frank Simon

Publications and source records attributed to Frank Simon.

At least 19 recordsLinked to original sources

Optimizing Sensor Placement for Hydrogen Leak Detection in Enclosed Infrastructure: A Comparative Study Using CFD-informed Genetic Algorithm and DeepSets Neural Surrogate

Hydrogen infrastructure in enclosed environments, such as parking facilities for fuel cell vehicles, presents significant safety challenges due to hydrogen's low ignition energy and wide flammability range. Current monitoring systems are largely reactive, detecting leaks only after hazardous concentrations have formed. This study develops a computational framework for proactive sensor placement optimization by integrating computational fluid dynamics (CFD), genetic algorithm (GA) optimization, and a DeepSets neural surrogate. A CFD database of 180 scenarios was generated for a representative 50 m x 30 m x 3 m garage, covering multiple leak positions, rates (1-150 g/s), and ventilation conditions (ACH = 3-10 per hour). Sensor placement was optimized using a multi-objective GA and compared with uniform, random, and surrogate-assisted approaches. The GA achieved a detection rate of 96.1% within 60 s and reduced blind areas to 0.12%, corresponding to an approximately 5% improvement in composite fitness over a uniform baseline. The DeepSets surrogate reproduced near-optimal configurations with a fitness gap below 0.01 while reducing CFD evaluations by 89% and computational time by two orders of magnitude. Detection performance and spatial coverage remained comparable to the GA, demonstrating that surrogate-assisted optimization can retain solution quality while enabling rapid design iteration. Overall, the results show that CFD-informed optimization improves detection effectiveness and reduces sensor requirements compared to conventional layouts. The proposed framework supports scalable deployment and provides a foundation for integrating optimized sensor networks with digital twin systems for real-time monitoring and risk assessment.

cs.NE

When Do Foundation Models Pay Off? A Break-Even Analysis of Pretrained Time Series Forecasters

Deploying a time series foundation model requires GPU infrastructure, engineering overhead, and carries no guarantee of improvement over XGBoost. We provide the first systematic break-even analysis answering when this investment pays off. Across 30 benchmark datasets, we compare zero-shot and LoRA fine-tuned foundation models (Chronos, Moirai, Lag-Llama) against classical baselines (Naive, ETS, ARIMA, XGBoost) at six training set sizes from 2% to 100% of available data. Foundation models outperform classical methods at every evaluated training fraction on 15 of 30 datasets -- GPU deployment is unconditionally justified on these regardless of data volume. On 6 datasets, classical methods surpass zero-shot foundation models with as little as 2% of training data (21-2,768 samples); on the remaining 9, break-even ranges from 24 to 8,361 samples. One robust deployment rule requires no model training: if n_train < 700 and seasonality is non-negligible, use FM zero-shot and skip fine-tuning -- this resolves 10 of 30 deployment decisions immediately. Contrary to common practice, LoRA fine-tuning can actively degrade performance on short series. We operationalise these findings as a two-step decision framework -- compute dataset length and seasonality strength, run a brief 5-10% pilot only if needed -- enabling practitioners to make the FM-versus-classical decision before committing to full infrastructure. Four dataset features motivate mechanistic hypotheses for the remaining cases, though reliable automated prediction at this benchmark scale remains an open problem. Code, benchmark, and decision tools are available at https://github.com/nicolaisi/fm-breakeven.

cs.LG

The Remote Analog to Digital Conversion DAQ System for the TRISTAN Detector Upgrade

The TRISTAN detector is an upgrade to the KATRIN experiment to enable a differential measurement of the tritium $\beta$-decay spectrum to search for sterile neutrinos with keV masses. This entails performing precision electron spectroscopy with over one thousand silicon drift detector pixels, each responsible for recording incident electron rates of $10^5$ counts per second. A project specific data acquisition (DAQ) system is developed to meet the experimental challenges through a remote analog to digital conversion (RADC) design. In this work, the conceptual design of the RADC DAQ is presented along with the built system for operating the TRISTAN detector upgrade. The system includes flexible signal processing logic and data management that is optimized for the high-rate precision measurement.

physics.ins-det

Timing performance of SiPM-on-Tile elements: Laboratory and test beam measurements

The SiPM-on-Tile technology for highly granular calorimeters, where small plastic scintillator tiles are directly read out with SiPMs, has been developed for the CALICE Analog Hadron Calorimeter, and has been adopted for parts of the hadronic section of the CMS High Granularity Calorimeter. For future electron-positron colliders, a single cell time stamping on the sub-nanosecond level for energy deposits corresponding to single minimum-ionizing particles is desired to provide background rejection and to support pattern recognition and energy reconstruction with particle flow algorithms. To better understand the time resolution achievable with the SiPM-on-Tile technology, we have performed detailed measurements in test beams at DESY, probing scintillator tiles of different sizes. The study is complemented by laser measurements that provide insights into processes within the scintillator tile relevant for timing. In this publication, we will discuss our measurement methods and the results of our SiPM-on-Tile timing study.

physics.ins-det

Focus topics for the ECFA study on Higgs / Top / EW factories

In order to stimulate new engagement and trigger some concrete studies in areas where further work would be beneficial towards fully understanding the physics potential of an $e^+e^-$ Higgs / Top / Electroweak factory, we propose to define a set of focus topics. The general reasoning and the proposed topics are described in this document.

hep-ph

Generalised Known Kinematics (GKK) An Approach for Kinematic Observables in Pair Production Events with Decays Involving Invisible Particles

Many analyses in high energy physics are limited due to missing kinematic information of known invisible particles in the detector, for example neutrinos. The undetected particle carries away momentum and energy information, preventing the full reconstruction of such an event. In this paper, we present a method to handle this missing information, referred to as the Generalised Known Kinematics (GKK) approach. It is based on constructing event-by-event probability density distributions that describe the physically allowed kinematics of an event. For GKK we take into account the available kinematic information and constraints given by the assumed final state. Summing these event-wise distributions over large data sets allows the determination of parameters that influence the event kinematics, such as particle masses, which are otherwise obscured by the missing information on the invisible final-state particles. The method is demonstrated in simulation studies with $τ^+ τ^-$ events in $e^+ e^-$ collisions at the $Υ$(4S) resonance, presenting a new, promising approach for the measurement of the $τ$ lepton mass.

hep-ex

Report of the Topical Group on Top quark physics and heavy flavor production for Snowmass 2021

This report summarizes the work of the Energy Frontier Topical Group on EW Physics: Heavy flavor and top quark physics (EF03) of the 2021 Community Summer Study (Snowmass). It aims to highlight the physics potential of top-quark studies and heavy-flavor production processes (bottom and charm) at the HL-LHC and possible future hadron and lepton colliders and running scenarios.

hep-ph

Time-assisted energy reconstruction in a highly-granular hadronic calorimeter

The software compensation algorithms developed for the CALICE Analog Hadron Calorimeter are extended to incorporate time information on the cell level, and the performance is studied in GEANT4 simulations with a detector model of a highly-granular SiPM-on-tile calorimeter. The addition of nanosecond-level time resolution is found to result in significant improvement of the energy resolution by approximately 3% to 4% for local software compensation compared to the software compensation based on local energy density alone, with further improvement possible with better timing resolution. The high correlation of energy density and time variables show that both provide sensitivity to correlated underlying shower features, which limits the potential of timing information when used as a global rather than a local variable.

physics.ins-det

Measurements of Beam Backgrounds in SuperKEKB Phase 2

The high design luminosity of the SuperKEKB electron-positron collider will result in challenging levels of beam-induced backgro\ unds in the interaction region. Understanding and mitigating these backgrounds is critical to the success of the Belle~II experi\ ment. We report on the first background measurements performed after roll-in of the Belle II detector, a period known as SuperKE\ KB Phase 2, utilizing both the BEAST II system of dedicated background detectors and the Belle II detector itself. We also repor\ t on first revisions to the background simulation made in response to our findings. Backgrounds measured include contributions f\ rom synchrotron radiation, beam-gas, Touschek, and injection backgrounds. At the end of Phase 2, single-beam backgrounds origina\ ting from the 4 GeV positron Low Energy Ring (LER) agree reasonably well with simulation, while backgrounds from the 7 GeV elect\ ron High Energy Ring (HER) are approximately one order of magnitude higher than simulation. We extrapolate these backgrounds for\ ward and conclude it is safe to install the Belle II vertex detector.

physics.ins-det

Higgs and top physics reconstruction challenges and opportunities at FCC-ee

The Higgs bosons and the top quark decay into rich and diverse final states, containing both light and heavy quarks, gluons, photons as well as W and Z bosons. This article reviews the challenges involved in reconstructing Higgs and top events at the FCC-ee and identifies the areas where novel developments are needed. The precise identification and reconstruction of these final states at the FCC-ee rely on the capability of the detector to provide excellent flavour tagging, jet energy and angular resolution, and global kinematic event reconstruction. Excellent flavour tagging performance requires low-material vertex and tracking detectors, and advanced machine learning techniques as successfully employed in LHC experiments. In addition, the Z pole run will provide abundant samples of heavy flavour partons that can be used for calibration of the tagging algorithms. For the reconstruction of jets, leptons, and missing energy, particle-flow algorithms are crucial to explore the full potential of the highly granular tracking and calorimeter systems, and give access to excellent energy-momentum resolution and precise identification of heavy bosons in their hadronic decays. This enables, among many other key elements, the reconstruction of Higgsstrahlung processes with leptonically and hadronically decaying Z bosons, and an almost background-free identification of top quark pair events. Exploiting the full available kinematic constraints together with exclusive jet clustering algorithms will allow for the optimisation of global event reconstruction with kinematic fitting techniques.

hep-ex

A time resolved study of injection backgrounds during the first commissioning phase of SuperKEKB

We report on measurements of beam backgrounds during the first commissioning phase of the SuperKEKB collider in 2016, performed with the plastic scintillator and silicon photomultiplier-based CLAWS detector system. The sub-nanosecond time resolution and single particle detection capability of the sensors allow bunch-by-bunch measurements, enable CLAWS to perform a novel time resolved analysis of beam backgrounds, and make the system uniquely suited for the study of injection backgrounds. We present measurements of various aspects of regular beam background and injection backgrounds which include time structure and decay behavior of injection backgrounds, hit-energy spectra and overall background rates. These measurements show that the elevated background rates following an injection generally last for several milliseconds, with the majority of the background particles typically observed within the first 500 us. The injection backgrounds exhibit pronounced patterns in time, connected to betatron and synchrotron oscillations in the accelerator rings. The frequencies of these patterns are determined from detector data.

physics.ins-det

ILC Study Questions for Snowmass 2021

To aid contributions to the Snowmass 2021 US Community Study on physics at the International Linear Collider and other proposed $e^+e^-$ colliders, we present a list of study questions that could be the basis of useful Snowmass projects. We accompany this with links to references and resources on $e^+e^-$ physics, and a description of a new software framework that we are preparing for $e^+e^-$ studies at Snowmass.

hep-ph

Scanning Strategies at the Top Threshold at ILC

A scan of the top quark pair production threshold at a future electron-positron collider provides the possibility for high-precision measurements of the top quark mass, and, when using two dimensional fits of the measured cross sections, also of other properties such as the width and the Yukawa coupling. The energy range of the scan and the distribution of the integrated luminosity can be optimized depending on the main goals of the threshold program. This contribution examines the possibility to determine the top quark mass in fast exploratory measurements with an adequate precision to enable such an optimization, and studies a scanning program with a reduced energy range of 6 GeV for the measurement of the mass, width and the Yukawa coupling, taking theoretical uncertainties from QCD scale variations and parametric uncertainties from the strong coupling constant into account.

hep-ex

Tests of the Standard Model at the International Linear Collider

We present an overview of the capabilities that the International Linear Collider (ILC) offers for precision measurements that probe the Standard Model. First, we discuss the improvements that the ILC will make in precision electroweak observables, both from W boson production and radiative return to the Z at 250 GeV in the center of mass and from a dedicated GigaZ stage of running at the Z pole. We then present new results on precision measurements of fermion pair production, including the production of b and t quarks. We update the ILC projections for the determination of Higgs boson couplings through a Standard Model Effective Field Theory fit taking into account the new information on precision electroweak constraints. Finally, we review the capabilities of the ILC to measure the Higgs boson self-coupling.

hep-ex

Silicon Photomultipliers in Particle and Nuclear Physics

Following first large-scale applications in highly granular calorimeters and in neutrino detectors, Silicon Photomultipliers have seen a wide adoption in accelerator-based particle and nuclear physics experiments. Today, they are used for a wide range of different particle detector types, ranging from calorimeters and trackers to particle identification and veto detectors, large volume detectors for neutrino physics and timing systems. This article reviews the current state and expected evolution of these applications, highlighting strengths and limitation of SiPMs and the corresponding design choices in the respective contexts. General trends and adopted technical solutions in the applications are discussed.

physics.ins-det

A highly granular SiPM-on-tile calorimeter prototype

The Analogue Hadron Calorimeter (AHCAL) developed by the CALICE collaboration is a scalable engineering prototype for a Linear Collider detector. It is a sampling calorimeter of steel absorber plates and plastic scintillator tiles read out by silicon photomultipliers (SiPMs) as active material (SiPM-on-tile). The front-end chips are integrated into the active layers of the calorimeter and are designed for minimizing power consumption by rapidly cycling the power according to the beam structure of a linear accelerator. 38 layers of the sampling structure are equipped with cassettes containing 576 single channels each, arranged on readout boards and grouped according to the 36 channel readout chips. The prototype has been assembled using techniques suitable for mass production, such as injection-moulding and semi-automatic wrapping of scintillator tiles, assembly of scintillators on electronics using pick-and-place machines and mass testing of detector elements. The calorimeter was commissioned at DESY and was taking data at the CERN SPS at the time of the conference. The contribution discusses the construction, commissioning and first test beam results of the CALICE AHCAL engineering prototype.

physics.ins-det

The International Linear Collider: A Global Project

The International Linear Collider (ILC) is now under consideration as the next global project in particle physics. In this report, we review of all aspects of the ILC program: the physics motivation, the accelerator design, the run plan, the proposed detectors, the experimental measurements on the Higgs boson, the top quark, the couplings of the W and Z bosons, and searches for new particles. We review the important role that polarized beams play in the ILC program. The first stage of the ILC is planned to be a Higgs factory at 250 GeV in the centre of mass. Energy upgrades can naturally be implemented based on the concept of a linear collider. We discuss in detail the ILC program of Higgs boson measurements and the expected precision in the determination of Higgs couplings. We compare the ILC capabilities to those of the HL-LHC and to those of other proposed e+e- Higgs factories. We emphasize throughout that the readiness of the accelerator and the estimates of ILC performance are based on detailed simulations backed by extensive RandD and, for the accelerator technology, operational experience.

hep-ex

A detector for CLIC: main parameters and performance

Together with the recent CLIC detector model CLICdet a new software suite was introduced for the simulation and reconstruction of events in this detector. This note gives a brief introduction to CLICdet and describes the CLIC experimental conditions at 380 GeV and 3 TeV, including beam-induced backgrounds. The simulation and reconstruction tools are introduced, and the physics performance obtained is described in terms of single particles, particles in jets, jet energy resolution and flavour tagging. The performance of the very forward electromagnetic calorimeters is also discussed.

physics.ins-det