arXiv subjects

F. Richard

Publications and source records attributed to F. Richard.

At least 19 recordsLinked to original sources

arXiv2026

$e^+e^- \rightarrow s\bar{s}$ at $\sqrt{s} = 250$ GeV at future linear colliders

The forward-backward asymmetry ($A_{FB}$) in light-quark production is a sensitive probe of the electroweak sector and potential flavour-dependent BSM effects. We present a study of $e^+e^- \rightarrow s\bar{s}$ at $\sqrt{s}=250$ GeV at future linear colliders, using full ILD simulation and reconstruction tools for ILC and LCF@CERN. We assess the impact of particle identification on charge reconstruction and $A_{FB}$ extraction, considering software improvements using Comprehensive PID (CPID) for optimal $dE/dx$ usage, as well as hardware scenarios including cluster counting ($dN/dx$) and ideal TPC performance. Statistical precision gains are evaluated, with corrections for charge misidentification and acceptance applied. Results indicate that precise $A_{FB}^{s\bar{s}}$ measurements are feasible and that advanced PID is key to maximising sensitivity to electroweak and new-physics effects.

hep-ex↗

arXiv2024

Shower Separation in Five Dimensions for Highly Granular Calorimeters using Machine Learning

To achieve state-of-the-art jet energy resolution for Particle Flow, sophisticated energy clustering algorithms must be developed that can fully exploit available information to separate energy deposits from charged and neutral particles. Three published neural network-based shower separation models were applied to simulation and experimental data to measure the performance of the highly granular CALICE Analogue Hadronic Calorimeter (AHCAL) technological prototype in distinguishing the energy deposited by a single charged and single neutral hadron for Particle Flow. The performance of models trained using only standard spatial and energy and charged track position information from an event was compared to models trained using timing information available from AHCAL, which is expected to improve sensitivity to shower development and, therefore, aid in clustering. Both simulation and experimental data were used to train and test the models and their performances were compared. The best-performing neural network achieved significantly superior event reconstruction when timing information was utilised in training for the case where the charged hadron had more energy than the neutral one, motivating temporally sensitive calorimeters. All models under test were observed to tend to allocate energy deposited by the more energetic of the two showers to the less energetic one. Similar shower reconstruction performance was observed for a model trained on simulation and applied to data and a model trained and applied to data.

physics.ins-det↗

arXiv2024

Probing gauge-Higgs Unification models at the ILC with quark-antiquark forward-backward asymmetry at center-of-mass energies above the Z mass

The International Linear Collider (ILC) will allow the precise study of $e^{-}e^{+}\rightarrow q\bar{q}$ interactions at different center-of-mass energies from the $Z$-pole to 1 TeV. In this paper, we discuss the experimental prospects for measuring differential observables in $e^{-}e^{+}\rightarrow b\bar{b}$ and $e^{-}e^{+}\rightarrow c\bar{c}$ at the ILC baseline energies, 250 and 500 GeV. The study is based on full simulation and reconstruction of the International Large Detector (ILD) concept. Two gauge-Higgs unification models predicting new high-mass resonances beyond the Standard Model are discussed. These models predict sizable deviations of the forward-backward observables at the ILC running above the $Z$ mass and with longitudinally polarized electron and positron beams. The ability of the ILC to probe these models via high-precision measurements of the forward-backward asymmetry is discussed. Alternative scenarios at other energies and beam polarization schemes are also discussed, extrapolating the estimated uncertainties from the two baseline scenarios.

hep-ph↗

arXiv2024

Software Compensation for Highly Granular Calorimeters using Machine Learning

A neural network for software compensation was developed for the highly granular CALICE Analogue Hadronic Calorimeter (AHCAL). The neural network uses spatial and temporal event information from the AHCAL and energy information, which is expected to improve sensitivity to shower development and the neutron fraction of the hadron shower. The neural network method produced a depth-dependent energy weighting and a time-dependent threshold for enhancing energy deposits consistent with the timescale of evaporation neutrons. Additionally, it was observed to learn an energy-weighting indicative of longitudinal leakage correction. In addition, the method produced a linear detector response and outperformed a published control method regarding resolution for every particle energy studied.

physics.ins-det↗

arXiv2023

Experimental methods and prospects on the measurement of electroweak $b$ and $c$-quark observables at the ILC operating at 250 GeV

This paper describes a comprehensive experimental study on viability and prospects for the measurement of electroweak observables in $e^{+}e^{-}\rightarrow b\bar{b}$ and $e^{+}e^{-}\rightarrow c\bar{c}$ processes at the International Linear Collider (ILC) operating at 250 GeV of centre of mass energy. The ILC will produce electron and positron beams with different degrees of longitudinal polarisation (up to 80$\%$ for electrons and $30\%$ for positrons). The studies are based on a detailed simulation of the International Large Detector (ILD) concept. This will allow to inspect in detail the four independent chirality combinations of the electroweak couplings to electrons and other fermions and also perform background free analysis. The ILD design is based on the particle flow approach and the excellent vertexing and tracking capabilities, including charged hadron identification thanks to the $dE/dx$. We evaluate the main sources of experimental systematic uncertainties and identify the key design aspects of the accelerator and detector that are crucial to achieve the required per mil level accuracy that matches the expected statistical accuracy.

hep-ex↗

arXiv2022

Energy reconstruction of hadronic showers at the CERN PS and SPS using the Semi-Digital Hadronic Calorimeter

The CALICE Semi-Digital Hadronic CALorimeter (SDHCAL) is the first technological prototype in a family of high-granularity calorimeters developed by the CALICE Collaboration to equip the experiments of future lepton colliders. The SDHCAL is a sampling calorimeter using stainless steel for absorber and Glass Resistive Plate Chambers (GRPC) as a sensitive medium. The GRPC are read out by 1~cm $\times$ 1~cm pickup pads combined to a multi-threshold electronics. The prototype was exposed to hadron beams in both the CERN PS and the SPS beamlines in 2015 allowing the test of the SDHCAL in a large energy range from 3~GeV to 80~GeV. After introducing the method used to select the hadrons of our data and reject the muon and electron contamination, we present the energy reconstruction approach that we apply to the data collected from both beamlines and we discuss the response linearity and the energy resolution of the SDHCAL. The results obtained in the two beamlines confirm the excellent SDHCAL performance observed with the data collected with the same prototype in the SPS beamline in 2012. They also show the stability of the SDHCAL in different beam conditions and different time periods.

hep-ex↗

arXiv2021

Properties of slowly rotating asteroids from the Convex Inversion Thermophysical Model

Results from the TESS mission showed that previous studies strngly underestimated the number of slow rotators, revealing the importance of studying those asteroids. For most slowly rotating asteroids (P > 12), no spin and shape model is available because of observation selection effects. This hampers determination of their thermal parameters and accurate sizes. We continue our campaign in minimising selection effects among main belt asteroids. Our targets are slow rotators with low light-curve amplitudes. The goal is to provide their scaled spin and shape models together with thermal inertia, albedo, and surface roughness to complete the statistics. Rich multi-apparition datasets of dense light curves are supplemented with data from Kepler and TESS. In addition to data in the visible range, we also use thermal data from infrared space observatories (IRAS, Akari and WISE) in a combined optimisation process using the Convex Inversion Thermophysical Model (CITPM). This novel method has so far been applied to only a few targets, and in this work we further validate the method. We present the models of 16 slow rotators. All provide good fits to both thermal and visible data. The obtained sizes are on average accurate at the 5% precision, with diameters in the range from 25 to 145 km. The rotation periods of our targets range from 11 to 59 hours, and the thermal inertia covers a wide range of values, from 2 to <400 SI units, not showing any correlation with the period. With this work we increase the sample of slow rotators with reliable spin and shape models and known thermal inertia by 40%. The thermal inertia values of our sample do not display a previously suggested increasing trend with rotation period, which might be due to their small skin depth.

astro-ph.EP↗

arXiv2020

Particle Identification Using Boosted Decision Trees in the Semi-Digital Hadronic Calorimeter Prototype

The CALICE Semi-Digital Hadronic CALorimeter (SDHCAL) prototype using Glass Resistive Plate Chambers as a sensitive medium is the first technological prototype of a family of high-granularity calorimeters developed by the CALICE collaboration to equip the experiments of future leptonic colliders. It was exposed to beams of hadrons, electrons and muons several times in the CERN PS and SPS beamlines between 2012 and 2018. We present here a new method of particle identification within the SDHCAL using the Boosted Decision Trees (BDT) method applied to the data collected in 2015. The performance of the method is tested first with Geant4-based simulated events and then on the data collected by the SDHCAL in the energy range between 10 and 80~GeV with 10~GeV energy steps. The BDT method is then used to reject the electrons and muons that contaminate the SPS hadron beams.

physics.ins-det↗

arXiv2020

Production and measurement of $e^{+}e^{-}\rightarrow c\bar{c}$ signatures at the 250 GeV ILC

This document discusses for the first time the experimental prospects on the measurement of cross section and the forward-backward asymmetry in $e^{-}e^{+}\rightarrow c\bar{c}$ collisions at 250 GeV at the International Linear Collider operating polarised beams. The cross section will be normalised to the total hadronic cross section. We discuss the results for an analysis assuming the integrated luminosity of 2000 fb$^{-1}$ foreseen in the baseline project. The measurement requires determining the charge of both jets identified as originated by a $c$-quark. The charge measurement is optimally performed using the precise micro-vertex detector of the detector ILD and the charged kaon identification provided by the $\frac{dE}{dx}$ information of its TPC. Thanks to the beam polarisation, we can separate the four independent chirality combinations of the electroweak couplings, enhancing in this way the sensitivity to new physics effects. We show that due to the unprecedented precision that will be achieved by the ILC for these observables, the ILC will be sensitive to the existence of beyond the standard model Randal Sundrum resonances of several tens of TeV.

hep-ex↗

arXiv2019

Complementarity between ILC250 and ILC-GigaZ

In view of the very precise measurements on fermion couplings which will be performed at ILC250 with polarized beams, there is emerging evidence that the LEP1/SLC measurements on these couplings are an order of magnitude too imprecise to match the accuracies reachable at ILC250. This will therefore severely limit the indirect sensitivity to new resonances and require revisiting the possibility to run ILC at the Z pole with polarized electrons. This work was done as a contribution to the ESU 2018-2020.

hep-ex↗

arXiv2019

Characterisation of different stages of hadronic showers using the CALICE Si-W ECAL physics prototype

A detailed investigation of hadronic interactions is performed using $\pi^-$-mesons with energies in the range 2--10 GeV incident on a high granularity silicon-tungsten electromagnetic calorimeter. The data were recorded at FNAL in 2008. The region in which the $\pi^-$-mesons interact with the detector material and the produced secondary particles are characterised using a novel track-finding algorithm that reconstructs tracks within hadronic showers in a calorimeter in the absence of a magnetic field. The principle of carrying out detector monitoring and calibration using secondary tracks is also demonstrated.

physics.ins-det↗

arXiv2019

Beam test performance of the highly granular SiW-ECAL technological prototype for the ILC

The technological prototype of the CALICE highly granular silicon-tungsten electromagnetic calorimeter (SiW-ECAL) was tested in a beam at DESY in 2017. The setup comprised seven layers of silicon sensors. Each layer comprised four sensors, with each sensor containing an array of 256 $5.5\times5.5$ mm$^2$ silicon PIN diodes. The four sensors covered a total area of $18\times18$ cm$^2$, and comprised a total of 1024 channels. The readout was split into a trigger line and a charge signal line. Key performance results for signal over noise for the two output lines are presented, together with a study of the uniformity of the detector response. Measurements of the response to electrons for the tungsten loaded version of the detector are also presented.

physics.ins-det↗

arXiv2019

Analysis of Testbeam Data of the Highly Granular RPC-Steel CALICE Digital Hadron Calorimeter and Validation of Geant4 Monte Carlo Models

We present a study of the response of the highly granular Digital Hadronic Calorimeter with steel absorbers, the Fe-DHCAL, to positrons, muons, and pions with momenta ranging from 2 to 60 GeV/c. Developed in the context of the CALICE collaboration, this hadron calorimeter utilises Resistive Plate Chambers as active media, interspersed with steel absorber plates. With a transverse granularity of $1\,\times\,1\,$cm$^{2}$ and a longitudinal segmentation of 38 layers, the calorimeter counted 350,208 readout channels, each read out with single-bit resolution (digital readout). The data were recorded in the Fermilab test beam in 2010-11. The analysis includes measurements of the calorimeter response and the energy resolution to positrons and muons, as well as detailed studies of various shower shape quantities. The results are compared to simulations based on Geant4, which utilise different electromagnetic and hadronic physics lists.

physics.ins-det↗

arXiv2018

Commissioning of the highly granular SiW-ECAL technological prototype

In this article we describe the commissioning and a first analysis of the the beam test performance of a small prototype of a highly granular silicon tungsten calorimeter. The prototype features detector elements with a channel number similar to that envisaged for e.g. the ILD Detector of the International Linear Collider (ILC). The analysis demonstrates the capability of the detector to record signals as low as 0.5 MIP. Further, no loss of performance has been observed when operating the detector in a high magnetic field.

physics.ins-det↗

arXiv2018

Hadronic Energy Resolution of a Combined High Granularity Scintillator Calorimeter System

This paper presents results obtained with the combined CALICE Scintillator Electromagnetic Calorimeter, Analogue Hadronic Calorimeter and Tail Catcher & Muon Tracker, three high granularity scintillator-SiPM calorimeter prototypes. The response of the system to pions with momenta between 4 GeV/c and 32 GeV/c is analysed, including the energy response, resolution, and longitudinal shower profiles. The results of a software compensation technique based on weighting according to hit energy are compared to those of a standard linear energy reconstruction. The results are compared to predictions of the GEANT4 physics lists QGSP_BERT_HP and FTFP_BERT_HP.

physics.ins-det↗

arXiv2017

Against the biases in spins and shapes of asteroids

Physical studies of asteroids depend on an availability of lightcurve data. Targets that are easy to observe and analyse naturally have more data available, so their synodic periods are confirmed from multiple sources. Also, thanks to availability of data from a number of apparitions, their spin and shape models can often be obtained. Almost half of bright (H<=11 mag) main-belt asteroid population with known lightcurve parameters have rotation periods considered long (P>12 hours) and are rarely chosen for photometric observations. There is a similar selection effect against asteroids with low lightcurve amplitudes (a_max<=0.25 mag). As a result such targets, though numerous in this brightness range, are underrepresented in the sample of spin and shape modelled asteroids. In the range of fainter targets such effects are stronger. These selection effects can influence what is now known about asteroid spin vs. size distribution, on asteroid internal structure and densities and on spatial orientation of asteroid spin axes. To reduce both biases at the same time, we started a photometric survey of a substantial sample of those bright main-belt asteroids that displayed both features: periods longer than 12 hours, and amplitudes that did not exceed 0.25 magnitude. First we aim at finding synodic periods of rotation, and after a few observed apparitions, obtaining spin and shape models. As an initial result of our survey we found that a quarter of the studied sample (8 out of 34 targets) have rotation periods different from those widely accepted. We publish here these newly found period values with the lightcurves. The size/frequency plot might in reality look different in the long-period range. Further studies of asteroid spins, shapes, and structure should take into account serious biases that are present in the parameters available today.

astro-ph.EP↗

arXiv2017

Measurement of b quark EW couplings at ILC

This paper describes an analysis performed at 250 GeV centre of mass energy for the reaction e+e- -> bbbar with the International Linear Collider, ILC, assuming an integrated luminosity of 500 fb-1. This measurement requires determining the b quark charge, which can be optimally performed using the precise micro-vertex detector of the detector ILD and the charged kaon identification provided by the dE/dx information of its TPC. Given that the forward backward asymmetry is maximal for e-L (Left-handed electron polarisation), it has been necessary to develop a new method to correct for unavoidable angular migration due to b charge mis-measurements. This correction is based on the reconstructed events themselves without introducing external corrections which would induce large uncertainties. With polarized beams, one can separate the Z and photon vector and axial couplings to b quarks. The precision reached is at the few per mill level, and should allow to confirm/discard the deviation observed at LEP1 on the ZbRbR coupling. Model independent upper bounds on the tensor couplings, F2V and F2A, are derived using the shape of the angular distribution.

hep-ex↗

arXiv2017

Construction and Response of a Highly Granular Scintillator-based Electromagnetic Calorimeter

A highly granular electromagnetic calorimeter with scintillator strip readout is being developed for future lepton collider experiments. A prototype of 21.5 $X_0$ depth and $180 \times 180 $mm$^2$ transverse dimensions was constructed, consisting of 2160 individually read out $10 \times 45 \times 3$ mm$^3$ scintillator strips. This prototype was tested using electrons of 2--32 GeV at the Fermilab Test Beam Facility in 2009. Deviations from linear energy response were less than 1.1\%, and the intrinsic energy resolution was determined to be $(12.5 \pm 0.1 (\mathrm{stat.}) \pm0.4 (\mathrm{syst.}))\%/\sqrt{E[\mathrm{GeV}]}\oplus (1.2 \pm 0.1(\mathrm{stat.})^{+0.6}_{-0.7}(\mathrm{syst.}))\%$, where the uncertainties correspond to statistical and systematic sources, respectively.

physics.ins-det↗