arXiv subjects

F. Caspers

Publications and source records attributed to F. Caspers.

At least 19 recordsLinked to original sources

arXiv2025

Search for solar axions produced through the axion-electron coupling $g_{ae}$ using a new GridPix detector at CAST

We present a search for solar axions produced through the axion-electron coupling $(g_{ae})$ using data from a novel 7-GridPix detector installed at the CERN Axion Solar Telescope (CAST). The detector, featuring ultra-thin silicon nitride windows and multiple veto systems, collected approximately 160 hours of solar tracking data between 2017-2018. Using machine learning techniques and the veto systems, we achieved a background rate of $1.06\times 10^{-5}\,\text{keV}^{-1}\text{cm}^{-2}\text{s}^{-1}$ at a signal efficiency of about $80\,\%$ in the $0.2$-$8\,\text{keV}$ range. Analysis of the data yielded no significant excess above background, allowing us to set a new upper limit on the product of the axion-electron and axion-photon couplings of $g_{ae}\cdot g_{a\gamma} < 7.35\times 10^{-23}\,\text{GeV}^{-1}$ at $95\,\%$ confidence level. This result improves upon the previous best helioscope limit and demonstrates the potential of GridPix technology for rare event searches. Additionally, we derived a limit on the axion-photon coupling of $g_{a\gamma} < 9.0\times 10^{-11}\,\text{GeV}^{-1}$ at $95\,\%$ CL, which, while not surpassing CAST's best limit, provides complementary constraints on axion models.

hep-ex↗

arXiv2024

A new upper limit on the axion-photon coupling with an extended CAST run with a Xe-based Micromegas detector

Hypothetical axions provide a compelling explanation for dark matter and could be emitted from the hot solar interior. The CERN Axion Solar Telescope (CAST) has been searching for solar axions via their back conversion to X-ray photons in a 9-T 10-m long magnet directed towards the Sun. We report on an extended run with the IAXO (International Axion Observatory) pathfinder detector, doubling the previous exposure time. The detector was operated with a xenon-based gas mixture for part of the new run, providing technical insights for future detector configurations in IAXO. No counts are detected in the 95% signal-encircling region during the new run, while 0.75 are expected. The new data improve the axion-photon coupling limit to 5.8$\times 10^{-11}\,$GeV$^{-1}$ at 95% C.L. (for $m_a \lesssim 0.02$ eV), the most restrictive experimental limit to date.

hep-ex↗

arXiv2024

Daily modulations and broadband strategy in axion searches. An application with CAST-CAPP detector

It has been previously advocated that the presence of the daily and annual modulations of the axion flux on the Earth's surface may dramatically change the strategy of the axion searches. The arguments were based on the so-called Axion Quark Nugget (AQN) dark matter model which was originally put forward to explain the similarity of the dark and visible cosmological matter densities $\Omega_{\rm dark}\sim \Omega_{\rm visible}$. In this framework, the population of galactic axions with mass $ 10^{-6} {\rm eV}\lesssim m_a\lesssim 10^{-3}{\rm eV}$ and velocity $\langle v_a\rangle\sim 10^{-3} c$ will be accompanied by axions with typical velocities $\langle v_a\rangle\sim 0.6 c$ emitted by AQNs. Furthermore, in this framework, it has also been argued that the AQN-induced axion daily modulation (in contrast with the conventional WIMP paradigm) could be as large as $(10-20)\%$, which represents the main motivation for the present investigation. We argue that the daily modulations along with the broadband detection strategy can be very useful tools for the discovery of such relativistic axions. The data from the CAST-CAPP detector have been used following such arguments. Unfortunately, due to the dependence of the amplifier chain on temperature-dependent gain drifts and other factors, we could not conclusively show the presence or absence of a dark sector-originated daily modulation. However, this proof of principle analysis procedure can serve as a reference for future studies.

hep-ex↗

arXiv2022

Search for Dark Matter Axions with CAST-CAPP

The CAST-CAPP axion haloscope, operating at CERN inside the CAST dipole magnet, has searched for axions in the 19.74 $\mu$eV to 22.47 $\mu$eV mass range. The detection concept follows the Sikivie haloscope principle, where Dark Matter axions convert into photons within a resonator immersed in a magnetic field. The CAST-CAPP resonator is an array of four individual rectangular cavities inserted in a strong dipole magnet, phase-matched to maximize the detection sensitivity. Here we report on the data acquired for 4124 h from 2019 to 2021. Each cavity is equipped with a fast frequency tuning mechanism of 10 MHz/min between 4.774 GHz and 5.434 GHz. In the present work, we exclude axion-photon couplings for virialized galactic axions down to $g_{a{\gamma}{\gamma}} = 8 \times {10^{-14}}$ $GeV^{-1}$ at the 90% confidence level. The here implemented phase-matching technique also allows for future large-scale upgrades.

hep-ex↗

arXiv2021

First results of the CAST-RADES haloscope search for axions at 34.67 $\mu$eV

We present results of the Relic Axion Dark-Matter Exploratory Setup (RADES), a detector which is part of the CERN Axion Solar Telescope (CAST), searching for axion dark matter in the 34.67$\mu$eV mass range. A radio frequency cavity consisting of 5 sub-cavities coupled by inductive irises took physics data inside the CAST dipole magnet for the first time using this filter-like haloscope geometry. An exclusion limit with a 95% credibility level on the axion-photon coupling constant of g$_{a\gamma}\gtrsim 4\times10^{-13} \text{GeV}^{-1}$ over a mass range of 34.6738 $\mu$eV < $m_a$ < 34.6771 $\mu$eV is set. This constitutes a significant improvement over the current strongest limit set by CAST at this mass and is at the same time one of the most sensitive direct searches for an axion dark matter candidate above the mass of 25 $\mu$eV. The results also demonstrate the feasibility of exploring a wider mass range around the value probed by CAST-RADES in this work using similar coherent resonant cavities.

hep-ex↗

arXiv2016

RF Measurements of the New TOTEM Roman Pot

The TOTEM experiment has been designed to measure the total proton-proton cross section and to study the elastic and diffractive scattering at the LHC energy. The measurement requires detecting protons at distances as small as 1 mm from the beam center: TOTEM uses Roman Pots, movable beam pipe insertions, hosting silicon detectors. In the first period of LHC operation no relevant problems were detected with Roman Pots retracted or inserted during special runs. However, when operating the LHC with high intensity beams, impedance induced heating has been observed during the Roman Pots insertion. In order to be compatible with the higher LHC beam current foreseen after the LS1, a new version of the Roman Pot has been proposed and optimized with respect to the beam coupling impedance. In this work we present the bench impedance measurements carried out on the new Roman Pot prototype. Single and double wire measurements, as well as probe measurements, were performed in order to detect possible harmful resonant modes. The laboratory setup has been as well simulated with the help of CST Particle Studio in order to benchmark the measurement results. Measurements and simulations are in close agreement confirming the equipment compatibility with the LHC requirements for safe operation.

physics.ins-det↗

arXiv2014

Progress with the Upgrade of the SPS for the HL-LHC Era

The demanding beam performance requirements of the High Luminosity (HL-) LHC project translate into a set of requirements and upgrade paths for the LHC injector complex. In this paper the performance requirements for the SPS and the known limitations are reviewed in the light of the 2012 operational experience. The various SPS upgrades in progress and still under consideration are described, in addition to the machine studies and simulations performed in 2012. The expected machine performance reach is estimated on the basis of the present knowledge, and the remaining decisions that still need to be made concerning upgrade options are detailed.

physics.acc-ph↗

arXiv2014

Conceptual Design of the International Axion Observatory (IAXO)

The International Axion Observatory (IAXO) will be a forth generation axion helioscope. As its primary physics goal, IAXO will look for axions or axion-like particles (ALPs) originating in the Sun via the Primakoff conversion of the solar plasma photons. In terms of signal-to-noise ratio, IAXO will be about 4-5 orders of magnitude more sensitive than CAST, currently the most powerful axion helioscope, reaching sensitivity to axion-photon couplings down to a few $\times 10^{-12}$ GeV$^{-1}$ and thus probing a large fraction of the currently unexplored axion and ALP parameter space. IAXO will also be sensitive to solar axions produced by mechanisms mediated by the axion-electron coupling $g_{ae}$ with sensitivity $-$for the first time$-$ to values of $g_{ae}$ not previously excluded by astrophysics. With several other possible physics cases, IAXO has the potential to serve as a multi-purpose facility for generic axion and ALP research in the next decade. In this paper we present the conceptual design of IAXO, which follows the layout of an enhanced axion helioscope, based on a purpose-built 20m-long 8-coils toroidal superconducting magnet. All the eight 60cm-diameter magnet bores are equipped with focusing x-ray optics, able to focus the signal photons into $\sim 0.2$ cm$^2$ spots that are imaged by ultra-low-background Micromegas x-ray detectors. The magnet is built into a structure with elevation and azimuth drives that will allow for solar tracking for $\sim$12 h each day.

physics.ins-det↗

arXiv2013

First results of the CERN Resonant WISP Search (CROWS)

The CERN Resonant WISP Search (CROWS) probes the existence of Weakly Interacting Sub-eV Particles (WISPs) like axions or hidden sector photons. It is based on the principle of an optical light shining through the wall experiment, adapted to microwaves. Critical aspects of the experiment are electromagnetic shielding, design and operation of low loss cavity resonators and the detection of weak sinusoidal microwave signals. Lower bounds were set on the coupling constant $g = 4.5 \cdot 10^{-8} $GeV$^{-1}$ for axion like particles with a mass of $m_a = 7.2 \mu$eV. For hidden sector photons, lower bounds were set for the coupling constant $\chi = 4.1 \cdot 10^{-9}$ at a mass of $m_{\gamma'} = 10.8 \mu$eV. For the latter we were probing a previously unexplored region in the parameter space.

physics.ins-det↗

arXiv2013

Status report and first results of the microwave LSW experiment at CERN

To detect or exclude the existence of hidden sector photons or axion like particles, a table-top "microwaves shining through the wall" experiment has been set up at CERN. An overview of the experimental layout is given, the technical challenges involved are reviewed and the measurement procedure including data-evaluation and its results to date are shown.

physics.ins-det↗

arXiv2013

Status report of the CERN microwave axion experiment

"Light Shining Through the Wall" experiments can probe the existence of "axion like particles" through their weak coupling to photons. We have adapted such an experiment to the microwave regime and constructed the table top apparatus. This work presents an overview of the experimental setup and then focuses on our latest measurement run and its results. By operating the apparatus within a superconducting MRI magnet, competitive exclusion limits for axion like particles to the first generation optical light shining through the wall experiments have been achieved.

physics.ins-det↗

arXiv2013

Novel types of anti-ecloud surfaces

In high power RF devices for space, secondary electron emission appears as the main parameter governing the multipactor effect and as well as the e-cloud in large accelerators. Critical experimental activities included development of coatings with low secondary electron emission yield (SEY) for steel (large accelerators) and aluminium (space applications). Coatings with surface roughness of high aspect ratio producing the so-call secondary emission suppression effect appear as the selected strategy. In this work a detailed study of the SEY of these technological coatings and also the experimental deposition methods (PVD and electrochemical) are presented. The coating-design approach selected for new low SEY coatings include rough metals (Ag, Au, Al), rough alloys (NEG), particulated and magnetized surfaces, and also graphene like coatings. It was found that surface roughness also mitigate the SEY deterioration due to aging processes.

physics.acc-ph↗

arXiv2013

Dependence of e-cloud on the longitudinal bunch profile: studies in the PS & extension to the HL-LHC

Recent studies have shown that the prospects for significantly increasing bunch intensities in the LHC for the luminosity upgrade (HL-LHC) may be severely limited by the available cryogenic cooling capacity and the electron-cloud (EC) driven beam instability. However, it is planned that during the HL-LHC era the bunch intensities in the LHC will go up by nearly a factor of two compared to the LHC-design values. This motivates the exploration of additional EC mitigation techniques that can be adopted in addition to those already in place. Preliminary simulations indicated that long flat bunches can be beneficial over Gaussian bunches to reduce the EC build up. Rigorous studies using realistic bunch profiles have never been done. Therefore, we have undertaken an in-depth investigation in the CERN 26 GeV PS to see if we can validate the previous findings and, in particular, if flattening the bunch can mitigate the EC. Here we present the results from dedicated EC measurements in the PS using a variety of bunch shapes and a comparison with simulations. Finally, we investigate if reshaping the bunch profiles using a 2nd harmonic rf cavity can mitigate EC in the HL-LHC.

physics.acc-ph↗

arXiv2012

A microwave paraphoton and axion detection experiment with 300 dB electromagnetic shielding at 3 GHz

For the microwave equivalent of "light shining through the wall" (LSW) experiments, a sensitive microwave detector and very high electromagnetic shielding is required. The screening attenuation between the axion generating cavity and the nearby detection cavity should be greater than 300 dB, in order to improve over presently existing exclusion limits. To achieve these goals in practice, a "box in a box" concept was utilized for shielding the detection cavity, while a vector signal analyzer was used as a microwave receiver with a very narrow resolution bandwidth in the order of a few micro-Hz. This contribution will present the experimental layout and the results to date.

physics.ins-det↗

arXiv2012

Status report of the CERN light shining through the wall experiment with microwave axions and related aspects

One way to proof or exclude the existence of axion like particles is a microwave light shining through the wall experiment. In this publication we will emphasize on the engineering aspects of such a setup, currently under development at CERN. One critical point, to achieve meaningful results, is the electromagnetic shielding between axion-emitter and -receiver cavity, which needs to be in the order of 300 dB to improve over existing experimental bounds. The RF leakage or electromagnetic crosstalk between both cavities must be well controlled and quantified during the complete duration of the experiment. A very narrow band (in the 10^-6 Hz range) homodyne detection method is used to reveal the axion signal from background thermal noise. The current status of the experiment is presented.

physics.ins-det↗

arXiv2012

RF engineering basic concepts: the Smith chart

The Smith chart is a very valuable and important tool that facilitates interpretation of S-parameter measurements. This paper will give a brief overview on why and more importantly on how to use the chart. Its definition as well as an introduction on how to navigate inside the chart are illustrated. Useful examples show the broad possibilities for use of the chart in a variety of applications.

physics.acc-ph↗

arXiv2012

RF measurements I: signal receiving techniques

For the characterization of components, systems and signals in the RF and microwave range, several dedicated instruments are in use. In this paper the fundamentals of the RF-signal sampling technique, which has found widespread applications in 'digital' oscilloscopes and sampling scopes, are discussed. The key element in these front-ends is the Schottky diode which can be used either as an RF mixer or as a single sampler. The spectrum analyser has become an absolutely indispensable tool for RF signal analysis. Here the front-end is the RF mixer as the RF section of modern spectrum analysers has a rather complex architecture. The reasons for this complexity and certain working principles as well as limitations are discussed. In addition, an overview of the development of scalar and vector signal analysers is given. For the determination of the noise temperature of a one-port and the noise figure of a two-port, basic concepts and relations are shown. A brief discussion of commonly used noise measurement techniques concludes the paper.

physics.acc-ph↗

arXiv2012

RF engineering basic concepts: S-parameters

The concept of describing RF circuits in terms of waves is discussed and the S-matrix and related matrices are defined. The signal flow graph (SFG) is introduced as a graphical means to visualize how waves propagate in an RF network. The properties of the most relevant passive RF devices (hybrids, couplers, non-reciprocal elements, etc.) are delineated and the corresponding S-parameters are given. For microwave integrated circuits (MICs) planar transmission lines such as the microstrip line have become very important.

physics.acc-ph↗