arXiv subjects

Emil Björnson

Publications and source records attributed to Emil Björnson.

At least 289 records · Page 16Linked to original sources

arXiv2019

Techniques for System Information Broadcast in Cell-Free Massive MIMO

We consider transmission of system information in a cell-free massive MIMO system, when the transmitting access points do not have any channel state information and the receiving terminal has to estimate the channel based on downlink pilots. We analyze the system performance in terms of outage rate and coverage probability, and use space-time block codes to increase performance. We propose a heuristic method for pilot/data power optimization that can be applied without any channel state information at the access points. We also analyze the problem of grouping the access points, which is needed when the single-antenna access points jointly transmit a space-time block code.

cs.IT↗

arXiv2019

Large-Scale-Fading Decoding in Cellular Massive MIMO Systems with Spatially Correlated Channels

Massive multiple-input--multiple-output (MIMO) systems can suffer from coherent intercell interference due to the phenomenon of pilot contamination. This paper investigates a two-layer decoding method that mitigates both coherent and non-coherent interference in multi-cell Massive MIMO. To this end, each base station (BS) first estimates the channels to intra-cell users using either minimum mean-squared error (MMSE) or element-wise MMSE (EW-MMSE) estimation based on uplink pilots. The estimates are used for local decoding on each BS followed by a second decoding layer where the BSs cooperate to mitigate inter-cell interference. An uplink achievable spectral efficiency (SE) expression is computed for arbitrary two-layer decoding schemes. A closed-form expression is then obtained for correlated Rayleigh fading, maximum-ratio combining, and the proposed large-scale fading decoding (LSFD) in the second layer. We also formulate a sum SE maximization problem with both the data power and LSFD vectors as optimization variables. Since this is an NP-hard problem, we develop a low-complexity algorithm based on the weighted MMSE approach to obtain a local optimum. The numerical results show that both data power control and LSFD improves the sum SE performance over single-layer decoding multi-cell Massive MIMO systems.

cs.IT↗

arXiv2019

Massive MIMO in Sub-6 GHz and mmWave: Physical, Practical, and Use-Case Differences

The use of base stations (BSs) and access points (APs) with a large number of antennas, called Massive MIMO (multiple-input multiple-output), is a key technology for increasing the capacity of 5G networks and beyond. While originally conceived for conventional sub-6GHz frequencies, Massive MIMO (mMIMO) is ideal also for frequency bands in the range 30-300 GHz, known as millimeter wave (mmWave). Despite conceptual similarities, the way in which mMIMO can be exploited in these bands is radically different, due to their specific propagation behaviors and hardware characteristics. This paper reviews these differences and their implications, while dispelling common misunderstandings. Building on this foundation, we suggest appropriate signal processing schemes and use cases to efficiently exploit mMIMO in both frequency bands.

cs.IT↗

arXiv2019

How Energy-Efficient Can a Wireless Communication System Become?

The data traffic in wireless networks is steadily growing. The long-term trend follows Cooper's law, where the traffic is doubled every two-and-a-half year, and it will likely continue for decades to come. The data transmission is tightly connected with the energy consumption in the power amplifiers, transceiver hardware, and baseband processing. The relation is captured by the energy efficiency metric, measured in bit/Joule, which describes how much energy is consumed per correctly received information bit. While the data rate is fundamentally limited by the channel capacity, there is currently no clear understanding of how energy-efficient a communication system can become. Current research papers typically present values on the order of 10 Mbit/Joule, while previous network generations seem to operate at energy efficiencies on the order of 10 kbit/Joule. Is this roughly as energy-efficient future systems (5G and beyond) can become, or are we still far from the physical limits? These questions are answered in this paper. We analyze a different cases representing potential future deployment and hardware characteristics.

cs.IT↗

arXiv2018

Power Control for D2D Underlay in Multi-cell Massive MIMO Networks

This paper proposes a new power control and pilot allocation scheme for device-to-device (D2D) communication underlaying a multi-cell massive MIMO system. In this scheme, the cellular users in each cell get orthogonal pilots which are reused with reuse factor one across cells, while the D2D pairs share another set of orthogonal pilots. We derive a closed-form capacity lower bound for the cellular users with different receive processing schemes. In addition, we derive a capacity lower bound for the D2D receivers and a closed-form approximation of it. Then we provide a power control algorithm that maximizes the minimum spectral efficiency (SE) of the users in the network. Finally, we provide a numerical evaluation where we compare our proposed power control algorithm with the maximum transmit power case and the case of conventional multi-cell massive MIMO without D2D communication. Based on the provided results, we conclude that our proposed scheme increases the sum spectral efficiency of multi-cell massive MIMO networks.

cs.IT↗

arXiv2018

What Role Can NOMA Play in Massive MIMO?

This paper seeks to answer a simple but fundamental question: What role can NOMA play in massive MIMO? It is well-established that power-domain non-orthogonal multiple access (NOMA) schemes can outperform conventional orthogonal multiple access (OMA) schemes in cellular networks. However, this fact does not imply that NOMA is the most efficient way to communicate in massive MIMO setups, where the base stations have many more antennas than there are users in the cell. These setups are becoming the norm in future networks and are usually studied by assuming spatial multiplexing of the users using linear multi-user beamforming. To answer the above question, we analyze and compare the performance achieved by NOMA and multi-user beamforming in both NLOS and LOS scenarios. We reveal that the latter scheme gives the highest average sum rate in massive MIMO setups. We also identify specific cases where NOMA is the better choice in massive MIMO and explain how NOMA plays an essential role in creating a hybrid of NOMA and multi-user beamforming that is shown to perform better than two standalone schemes do.

cs.IT↗

arXiv2018

Humans and Machines can be Jointly Spatially Multiplexed by Massive MIMO

Future cellular networks are expected to support new communication paradigms such as machine-type communication (MTC) services along with conventional human-type communication (HTC) services. This requires base stations to serve a large number of devices in relatively short channel coherence intervals, which renders allocation of orthogonal pilot sequences per-device in each cell impractical. Furthermore, the stringent power constraints, place-and-play type connectivity and various data rate requirements of MTC devices make it impossible for the traditional cellular architecture to accommodate MTC and HTC services together. Massive multiple-input-multiple-output (mMIMO) technology has the potential to allow the coexistence of HTC and MTC services, thanks to its inherent spatial multiplexing properties and low transmission power requirements. In this work, we first tackle the optimal non-orthogonal pilot design problem and demonstrate that the optimal pilot sequences are Welch bound equality sequences. In the second part, we investigate the performance of a single cell under a shared physical channel assumption for MTC and HTC services and propose a novel scheme for sharing the time-frequency resources. The analysis reveals that mMIMO can significantly enhance the performance of such a setup and allow the inclusion of MTC services into the cellular networks without requiring additional resources.

cs.IT↗

arXiv2018

Network Deployment for Maximal Energy Efficiency in Uplink with Multislope Path Loss

This work aims to design the uplink (UL) of a cellular network for maximal energy efficiency (EE). Each base station (BS) is randomly deployed within a given area and is equipped with $M$ antennas to serve $K$ user equipments (UEs). A multislope (distance-dependent) path loss model is considered and linear processing is used, under the assumption that channel state information is acquired by using pilot sequences (reused across the network). Within this setting, a lower bound on the UL spectral efficiency and a realistic circuit power consumption model are used to evaluate the network EE. Numerical results are first used to compute the optimal BS density and pilot reuse factor for a Massive MIMO network with three different detection schemes, namely, maximum ratio combining, zero-forcing (ZF) and multicell minimum mean-squared error. The numerical analysis shows that the EE is a unimodal function of BS density and achieves its maximum for a relatively small density of BS, irrespective of the employed detection scheme. This is in contrast to the single-slope (distance-independent) path loss model, for which the EE is a monotonic non-decreasing function of BS density. Then, we concentrate on ZF and use stochastic geometry to compute a new lower bound on the spectral efficiency, which is then used to optimize, for a given BS density, the pilot reuse factor, number of BS antennas and UEs. Closed- form expressions are computed from which valuable insights into the interplay between optimization variables, hardware characteristics, and propagation environment are obtained.

cs.IT↗

arXiv2018

Channel Hardening and Favorable Propagation in Cell-Free Massive MIMO with Stochastic Geometry

Cell-Free (CF) Massive MIMO is an alternative topology for future wireless networks, where a large number of single-antenna access points (APs) are distributed over the coverage area. There are no cells but all users are jointly served by the APs using network MIMO methods. Prior works have claimed that CF Massive MIMO inherits the basic properties of cellular Massive MIMO, namely channel hardening and favorable propagation. In this paper, we evaluate if one can rely on these properties when having a realistic stochastic AP deployment. Our results show that channel hardening only appears in special cases, for example, when the pathloss exponent is small. However, by using 5--10 antennas per AP, instead of one, we can substantially improve the hardening. Only spatially well-separated users will exhibit favorable propagation, but when adding more antennas and/or reducing the pathloss exponent, it becomes more likely for favorable propagation to occur. The conclusion is that we cannot rely on channel hardening and favorable propagation when analyzing and designing CF Massive MIMO networks, but we need to use achievable rate expressions and resource allocation schemes that work well also in the absence of these properties. Some options are reviewed in this paper.

cs.IT↗

arXiv2018

When Is the Achievable Rate Region Convex in Two-User Massive MIMO Systems?

This letter investigates the achievable rate region in Massive multiple-input-multiple-output (MIMO) systems with two users, with focus on the i.i.d.~Rayleigh fading and line-of-sight (LoS) scenarios. If the rate region is convex, spatial multiplexing is preferable to orthogonal scheduling, while the opposite is true for non-convex regions. We prove that the uplink and downlink rate regions with i.i.d.~Rayleigh fading are convex, while the convexity in LoS depends on parameters such as angular user separation, number of antennas, and signal-to-noise ratio (SNR).

cs.IT↗

arXiv2018

Can Hardware Distortion Correlation be Neglected When Analyzing Uplink SE in Massive MIMO?

This paper analyzes how the distortion created by hardware impairments in a multiple-antenna base station affects the uplink spectral efficiency (SE), with focus on Massive MIMO. The distortion is correlated across the antennas, but has been often approximated as uncorrelated to facilitate (tractable) SE analysis. To determine when this approximation is accurate, basic properties of the distortion correlation are first uncovered. Then, we focus on third-order non-linearities and prove analytically and numerically that the correlation can be neglected in the SE analysis when there are many users. In i.i.d. Rayleigh fading with equal signal-to-noise ratios, this occurs when having five users.

cs.IT↗

arXiv2018

Uplink Spectral Efficiency of Massive MIMO with Spatially Correlated Rician Fading

This paper considers the uplink (UL) of a multi-cell Massive MIMO (multiple-input multiple-output) system with spatially correlated Rician fading channels. The channel model is composed of a deterministic line-of-sight (LoS) path and a stochastic non-line-of-sight (NLoS) component describing a spatially correlated multipath environment. We derive the statistical properties of the minimum mean squared error (MMSE) and least-square (LS) channel estimates for this model. Using these estimates for maximum ratio (MR) combining, rigorous closed-form UL spectral efficiency (SE) expressions are derived. Numerical results show that the SE is higher when using the MMSE estimator than the LS estimator, and the performance gap increases with the number of antennas. Moreover, Rician fading provides higher achievable SEs than Rayleigh fading since the LoS path improves the sum SE.

cs.IT↗

arXiv2018

The Essential Guide to Realizing 5G-Connected UAVs with Massive MIMO

What will it take for drones -- and the whole associated ecosystem -- to take off? Arguably, infallible command and control (C&C) channels for safe and autonomous flying, and high-throughput links for multi-purpose live video streaming. And indeed, meeting these aspirations may entail a full cellular support, provided through 5G-and-beyond hardware and software upgrades by both mobile operators and manufacturers of these unmanned aerial vehicles (UAVs). In this article, we vouch for massive MIMO as the key building block to realize 5G-connected UAVs. Through the sheer evidence of 3GPP-compliant simulations, we demonstrate how massive MIMO can be enhanced by complementary network-based and UAV-based solutions, resulting in consistent UAV C&C support, large UAV uplink data rates, and harmonious coexistence with legacy ground users.

cs.IT↗

arXiv2018

Understanding UAV Cellular Communications: From Existing Networks to Massive MIMO

The purpose of this article is to bestow the reader with a timely study of UAV cellular communications, bridging the gap between the 3GPP standardization status quo and the more forward-looking research. Special emphasis is placed on the downlink command and control (C&C) channel to aerial users, whose reliability is deemed of paramount technological importance for the commercial success of UAV cellular communications. Through a realistic side-by-side comparison of two network deployments -- a present-day cellular infrastructure versus a next-generation massive MIMO system -- a plurality of key facts are cast light upon, with the three main ones summarized as follows: (i) UAV cell selection is essentially driven by the secondary lobes of a base station's radiation pattern, causing UAVs to associate to far-flung cells; (ii) over a 10 MHz bandwidth, and for UAV heights of up to 300 m, massive MIMO networks can support 100 kbps C&C channels in 74% of the cases when the uplink pilots for channel estimation are reused among base station sites, and in 96% of the cases without pilot reuse across the network; (iii) supporting UAV C&C channels can considerably affect the performance of ground users on account of severe pilot contamination, unless suitable power control policies are in place.

cs.IT↗

arXiv2018

BER Performance Analysis of Coarse Quantized Uplink Massive MIMO

Having lower quantization resolution, has been introduced in the literature, as a solution to reduce the power consumption of massive MIMO and millimeter wave MIMO systems. In this paper, we analyze bit error rate (BER) performance of quantized uplink massive MIMO employing a few-bit resolution ADCs. Considering Zero-Forcing (ZF) detection, we derive a closed-form quantized signal-to-interference-plus-noise ratio (SINR) to achieve an analytical BER approximation for coarse quantized M-QAM massive MIMO systems, by using a linear quantization model. The proposed expression is a function of quantization resolution in bits. We further numerically investigate the effects of different quantization levels, from 1-bit to 4-bits, on the BER of three modulation types of QPSK, 16-QAM, and 64-QAM. Uniform and non-uniform quantizers are employed in our simulation. Monte Carlo simulation results reveal that our approximate formula gives a tight upper bound for the BER performance of $b$-bit resolution quantized systems using non-uniform quantizers, whereas the use of uniform quantizers cause a lower performance for the same systems. We also found a small BER performance degradation in coarse quantized systems, for example 2-3 bits QPSK and 3-4 bits 16-QAM, compared to the full-precision (unquantized) case. However, this performance degradation can be compensated by increasing the number of antennas at the BS.

eess.SP↗

arXiv2018

Downlink Power Control in Massive MIMO Networks with Distributed Antenna Arrays

In this paper, we investigate downlink power control in massive multiple-input multiple-output (MIMO) networks with distributed antenna arrays. The base station (BS) in each cell consists of multiple antenna arrays, which are deployed in arbitrary locations within the cell. Due to the spatial separation between antenna arrays, the large-scale propagation effect is different from a user to different antenna arrays in a cell, which makes power control a challenging problem as compared to conventional massive MIMO. We assume that the BS in each cell obtains the channel estimates via uplink pilots. Based on the channel estimates, the BSs perform maximum ratio transmission for the downlink. We then derive a closed-form spectral efficiency (SE) expression, where the channels are subject to correlated fading. Utilizing the derived expression, we propose a max-min power control algorithm to ensure that each user in the network receives a uniform quality of service. Numerical results demonstrate that, for the network considered in this work, optimizing for max-min SE through the max-min power control improves the sum SE of the network as compared to equal power allocation.

cs.IT↗

arXiv2018

Performance Analysis of Multi-User Massive MIMO Downlink under Channel Non-Reciprocity and Imperfect CSI

This paper analyzes the performance of linearly precoded time division duplex based multi-user massive MIMO downlink system under joint impacts of channel non-reciprocity (NRC) and imperfect channel state information (CSI). We consider a generic and realistic NRC model that accounts for transceiver frequency-response as well as mutual coupling mismatches at both user equipment (UE) and base station (BS) sides. The analysis covers two most prominent forms of linear precoding schemes, namely, zero-forcing (ZF) and maximum-ratio transmission (MRT), and assumes that only the statistical properties of the beamformed channel are used at the UE side to decode the received signal. Under the approximation of i.i.d. Gaussian channels, closed-form analytical expressions are derived for the effective signal to interference and noise ratios (SINRs) and the corresponding capacity lower bounds. The expressions show that, in moderate to high SNR, the additional interference caused by imperfect NRC calibration can degrade the performance of both precoders significantly. Moreover, ZF is shown to be more sensitive to NRC than MRT. Numerical evaluations with practical NRC levels indicate that this performance loss in the spectral efficiency can be as high as 42% for ZF, whereas it is typically less than 13% for MRT. It is also shown that due to the NRC, the asymptotic large-antenna performance of both precoders saturate to an identical finite level. The derived analytical expressions provide useful tools and valuable technical insight, e.g., into calculating the NRC calibration requirements in BSs and UEs for any given specific performance targets in terms of effective SINR or the system capacity bound.

cs.IT↗

arXiv2018

Distributed Power Control in Downlink Cellular Massive MIMO Systems

This paper compares centralized and distributed methods to solve the power minimization problem with quality-of-service (QoS) constraints in the downlink (DL) of multi-cell Massive multiple-input multiple-output (MIMO) systems. In particular, we study the computational complexity, number of parameters that need to be exchanged between base stations (BSs), and the convergence of iterative implementations. Although a distributed implementation based on dual decomposition (which only requires statistical channel knowledge at each BS) typically converges to the global optimum after a few iterations, many parameters need to be exchanged to reach convergence.

cs.IT↗