arXiv subjects

Cem Yalcin

Publications and source records attributed to Cem Yalcin.

6 recordsLinked to original sources

arXiv2025

DustNet: A Wireless Network of Ultrasonic Neural Implants

Spatially distributed peripheral nerve recordings can be used to reconstruct motor intention and improve natural control of prosthetics However, many existing clinical solutions rely on percutaneous wires to access peripheral nerves; these sites are prone to infection and motion-induced electrode degradation, preventing chronic use. To address the need for fully wireless neural recording systems, this paper presents DustNet: a spatially-distributed network of ultrasonically-powered neural recording implants capable of supporting up to 8 simultaneously recording nodes over a single ultrasound link. To enable high throughput multi-implant communication, DustNet implements a time-division multiple-access (TDMA) protocol with up to 16-level amplitude modulation of the ultrasound backscatter that achieves up to 4x higher data rates than traditional on-off keying methods. Each neural implant consists of a 0.7x0.7x0.7 mm$^3$ piezoceramic transducer, a 100 nF off-chip capacitor, and an IC mounted on a flexible PCB. The implant IC was fabricated in a 28nm CMOS process and occupies an area of 0.43 mm$^2$. System functionality was verified at 90mm depth in oil, achieving a maximum measured data rate of 200 kb/s at 2 MHz ultrasound carrier frequency, with each implant transmitting uplink data at 50 kb/s and dissipating just 7 $\mu$W; the system is demonstrated to support up to 400 kb/s total data rate over the same link.

eess.SY↗

arXiv2023

Fast non-iterative algorithm for 3D point-cloud holography

Recently developed iterative and deep learning-based approaches to computer-generated holography (CGH) have been shown to achieve high-quality photorealistic 3D images with spatial light modulators. However, such approaches remain overly cumbersome for patterning sparse collections of target points across a photoresponsive volume in applications including biological microscopy and material processing. Specifically, in addition to requiring heavy computation that cannot accommodate real-time operation in mobile or hardware-light settings, existing sampling-dependent 3D CGH methods preclude the ability to place target points with arbitrary precision, limiting accessible depths to a handful of planes. Accordingly, we present a non-iterative point cloud holography algorithm that employs fast deterministic calculations in order to efficiently allocate patches of SLM pixels to different target points in the 3D volume and spread the patterning of all points across multiple time frames. Compared to a matched-performance implementation of the iterative Gerchberg-Saxton algorithm, our algorithm's relative computation speed advantage was found to increase with SLM pixel count, exceeding 100,000x at 512x512 array format.

cs.GR↗

arXiv2022

A Sparse Sampling Sensor Front-end IC for Low Power Continuous SpO$_2$ \& HR Monitoring

Photoplethysmography (PPG) is an attractive method to acquire vital signs such as heart rate and blood oxygenation and is frequently used in clinical and at-home settings. Continuous operation of health monitoring devices demands a low power sensor that does not restrict the device battery life. Silicon photodiodes (PD) and LEDs are commonly used as the interface devices in PPG sensors; however, using of flexible organic devices can enhance the sensor conformality and reduce the cost of fabrication. In most PPG sensors, most of system power consumption is concentrated in powering LEDs, traditionally consuming mWs. Using organic devices further increases this power demand since these devices exhibit larger parasitic capacitances and typically need higher drive voltages. This work presents a sensor IC for continuous SpO$_2$ and HR monitoring that features an on-chip reconstruction-free sparse sampling algorithm to reduce the overall system power consumption by $\sim$70\% while maintaining the accuracy of the output information. The designed frontend is compatible with a wide range of devices from silicon PDs to organic PDs with parasitic capacitances up to 10 nF. Implemented in a 40 nm HV CMOS process, the chip occupies 2.43 mm$^2$ and consumes 49.7 $μ$W and 15.2 $μ$W of power in continuous and sparse sampling modes respectively. The performance of the sensor IC has been verified \textit{in vivo} with both types of devices and the results are compared against a clinical grade reference. Less than 1 bpm and 1\% mean absolute errors were achieved in both continuous and sparse modes of operation.

eess.SY↗

arXiv2021

A MEMS-based optical scanning system for precise, high-speed neural interfacing

Optical scanning is a prevalent technique for optical neural interfaces where light delivery with high spatial and temporal precision is desired. However, due to the sequential nature of point-scanning techniques, the settling time of optical modulators is a major bottleneck for throughput and limits random-access targeting capabilities. While fast lateral scanners exist, commercially available varifocal elements are constrained to >3ms settling times, limiting the speed of the overall system to hundreds of Hz. Faster focusing methods exist but cannot combine fast operation and dwelling capability with electrical and optical efficiency. Here, we present a varifocal mirror comprised of an array of piston-motion MEMS micromirrors and a custom driver ASIC, offering fast operation with dwelling capability while maintaining high diffraction efficiency. The ASIC features a reconfigurable nonlinear DAC to simultaneously compensate for the built-in nonlinearity of electrostatic actuators and the global process variations in MEMS mirrors. Experimental results demonstrate a wide continuous sweeping range that spans 22 distinctly resolvable depth planes with refresh rates greater than 12 kHz.

physics.app-ph↗

arXiv2020

A micromirror array with annular partitioning for high-speed random-access axial focusing

Dynamic axial focusing functionality has recently experienced widespread incorporation in microscopy, augmented/virtual reality (AR/VR), adaptive optics, and material processing. However, the limitations of existing varifocal tools continue to beset the performance capabilities and operating overhead of the optical systems that mobilize such functionality. The varifocal tools that are the least burdensome to drive (ex: liquid crystal, elastomeric or optofluidic lenses) suffer from low (~ 100 Hz) refresh rates. Conversely, the fastest devices sacrifice either critical capabilities such as their dwelling capacity (ex: acoustic gradient lenses or monolithic micromechanical mirrors) or low operating overhead (e.g., deformable mirrors). Here, we present a general-purpose random-access axial focusing device that bridges these previously conflicting features of high speed, dwelling capacity and lightweight drive by employing low-rigidity micromirrors that exploit the robustness of defocusing phase profiles. Geometrically, the device consists of an 8.2 mm diameter array of piston-motion and 48 um-pitch micromirror pixels that provide 2pi phase shifting for wavelengths shorter than 1 100 nm with 10-90 % settling in 64.8 us (i.e., 15.44 kHz refresh rate). The pixels are electrically partitioned into 32 rings for a driving scheme that enables phase-wrapped operation with circular symmetry and requires less than 30 V per channel. Optical experiments demonstrated the array's wide focusing range with a measured ability to target 29 distinct, resolvable depth planes. Overall, the features of the proposed array offer the potential for compact, straightforward methods of tackling bottlenecked applications including high-throughput single-cell targeting in neurobiology and the delivery of dense 3D visual information in AR/VR.

physics.optics↗

arXiv2019

A Sub-mm$^3$ Ultrasonic Free-floating Implant for Multi-mote Neural Recording

A 0.8 mm$^3$ wireless, ultrasonically powered, free-floating neural recording implant is presented. The device is comprised only of a 0.25 mm$^2$ recording IC and a single piezoceramic resonator that is used for both power harvesting and data transmission. Uplink data transmission is performed by analog amplitude modulation of the ultrasound echo. Using a 1.78 MHz main carrier, >35 kbps/mote equivalent uplink data rate is achieved. A technique to linearize the echo amplitude modulation is introduced, resulting in <1.2\% static nonlinearity of the received signal over a $\pm$10 mV input range. The IC dissipates 37.7 $μ$W, while the neural recording front-end consumes 4 $μ$W and achieves a noise floor of 5.3 $μ$V$_{rms}$ in a 5 kHz bandwidth. This work improves sub-mm recording mote depth by >2.5x, resulting in the highest measured depth/volume ratio by $\sim$3x. Orthogonal subcarrier modulation enables simultaneous operation of multiple implants, using a single-element ultrasound external transducer. Dual-mote simultaneous power up and data transmission is demonstrated at a rate of 7 kS/s at the depth of 50 mm.

eess.SP↗