arXiv subjects

Carl Blair

Publications and source records attributed to Carl Blair.

18 recordsLinked to original sources

arXiv2026

First Demonstration of Optical Feedback Control to Parametric Instability at Advanced LIGO

Increasing the circulating power in gravitational-wave detectors to the megawatt level is essential for future sensitivity improvement, but this is critically limited by optomechanical parametric instabilities. Current mitigation strategies are projected to be inadequate against instabilities when circulating power reaches a megawatt. Optical feedback offers a novel independent paradigm to mitigate parametric instability. In this Letter, we report the first demonstration of optical feedback control in a full-scale gravitational wave detector. We successfully suppressed an unstable mode at 10.428 kHz, reducing the parametric gain from R = 2 to R < 0.02. This work validates optical feedback control as an effective mitigation scheme for kilometre-scale interferometric gravitational-wave detectors, providing an effective strategy to allow detectors to reach the megawatt level.

gr-qc↗

arXiv2026

A Novel Arm-Length Stabilization Scheme for Gravitational-Wave Detectors with AlGaAs/GaAs Coated Mirrors

The arm length stabilisation system is employed in gravitational-wave detectors to reduce the velocity of the mirrors such that the arm cavities can be brought onto resonance in a controlled manner required to attain the detector operating point. For future upgrades of current gravitational wave detectors such as A#, which will incorporate AlGaAs/GaAs coatings, the current frequency-doubled arm length stabilisation system is unsuitable due to excessive absorption of the frequency-doubled 532nm beam by the AlGaAs/GaAs coating. We propose a novel multi-wavelength arm length stabilisation scheme that uses both frequency-doubled and frequency-tripled beams. The 1596nm auxiliary locking beam is outside the absorption bands of AlGaAs/GaAs coating. It is frequencytripled to 532nm and phase-locked with the 1064nm science laser through its second harmonic at 532 nm. In a tabletop setup, we experimentally demonstrated the stable cavity detuning and robust cavity locking transition by controlling the 1596nm laser and 1064nm laser phase locked loop. This demonstration confirmed that the proposed novel arm length stabilisation scheme is compatible with future upgrades or third-generation gravitational wave detectors that use AlGaAs/GaAs-coated test masses.

physics.optics↗

arXiv2026

Birefringence in a Silicon Beamsplitter at 2um for Future Gravitational Wave Detectors

The next generation of gravitational wave detectors will move to cryogenic operation in order to reduce thermal noise and thermal distortion. This necessitates a change in mirror substrate with silicon being a good candidate. Birefringence is an effect that will degrade the sensitivity of a detector and is of greater concern in silicon due to its crystalline nature. We measure the birefringence in a <100> float zone silicon beamsplitter since we expect there to be a large inherent birefringence due to the spatial dispersion effect. We observe that the birefringence varied between $3.44 \pm 0.12 \times 10^{-7}$ and $1.63 \pm 0.05 \times 10^{-7}$ and estimate the birefringence along the <110> axis to be $1.64 \pm 0.5 \times 10^{-6}$ at 2um. We demonstrate this effect and argue that it strengthens the case for 2um and <100> silicon.

physics.optics↗

arXiv2025

Seismic Isolation of Optical Tables Using Piezo Actuators

Seismic isolation is crucial for gravitational wave detectors as it minimizes ground vibrations, enabling the detection of faint gravitational wave signals. An active seismic isolation platform for precision measurement experiments is described. The table features piezo actuation along five degrees of freedom: three translational actuations and two tip-tilt degrees of freedom along the horizontal axes. It is stiff in rotation about the vertical axes. A seismometer is used to sense table motion. Piezo actuators are used to suppress seismic noise with feedback control bandwidth of 0.3 to 3 Hz. Suppression levels ranging from 21 to 36 dB of seismic noise within the frequency range of 0.5 to 1.3 Hz are demonstrated, as measured by a witness seismometer on the table, with the suppression direction along the axis of the longitudinal translation of the suspended mirror on the table. The suppression results in 1 $\mathrm{\mathrm{nm/\sqrt{Hz}}}$ residual horizontal motion at 1 Hz. Limitations such as tilt-to-translation coupling that prevent actuation over the desired range of 0.03 to 3 Hz are discussed.

astro-ph.IM↗

arXiv2024

Demonstration of optical spring in an un-detuned cavity containing an optical parametric amplifier

Here we demonstrate the capacity to manipulate the optical spring (OS) effect by employing an optical parametric amplifier (OPA) within an optical cavity. We observed more than a factor of 2 increase in the OS frequency shift with the OPA. We also showed for the first time that the OS can be tuned by solely adjusting the OPA phase and showing an un-detuned cavity exhibiting an optical spring. The method can be applied to gravitational wave detectors in the signal recycling configuration to realize narrow bandwidth high sensitivity. The OS can be tuned to align the detector peak sensitivity frequency to known frequency continuous gravitational wave signals, dynamically tuned to track the gravitational wave signal from merging compact binaries or tuned to search for the post-merger signal of known binary coalescence.

physics.optics↗

arXiv2023

Single and coupled cavity mode sensing schemes using a diagnostic field

Precise optical mode matching is of critical importance in experiments using squeezed-vacuum states. Automatic spatial-mode matching schemes have the potential to reduce losses and improve loss stability. However, in quantum-enhanced coupled-cavity experiments, such as gravitational-wave detectors, one must also ensure that the sub-cavities are also mode matched. We propose a new mode sensing scheme, which works for simple and coupled cavities. The scheme requires no moving parts, nor tuning of Gouy phases. Instead a diagnostic field tuned to the HG20/LG10 mode frequency is used. The error signals are derived to be proportional to the difference in waist position, and difference in Rayleigh ranges, between the sub-cavity eigenmodes. The two error signals are separable by 90 degrees of demodulation phase. We demonstrate reasonable error signals for a simplified Einstein Telescope optical design. This work will facilitate routine use of extremely high levels of squeezing in current and future gravitational-wave detectors.

physics.optics↗

arXiv2023

Seismic noise characterization at a potential gravitational wave detector site in Australia

A critical consideration in the design of next generation gravitational wave detectors is the understanding of the seismic environment that can introduce coherent and incoherent noise of seismic origin at different frequencies. We present detailed low-frequency ambient seismic noise characterization (0.1--10~Hz) at the Gingin site in Western Australia. Unlike the microseism band (0.06--1~Hz) for which the power shows strong correlations with nearby buoy measurements in the Indian Ocean, the seismic spectrum above 1~Hz is a complex superposition of wind induced seismic noise and anthropogenic seismic noise which can be characterized using beamforming to distinguish between the effects of coherent and incoherent wind induced seismic noise combined with temporal variations in the spatio-spectral properties of seismic noise. This also helps characterizing the anthropogenic seismic noise. We show that wind induced seismic noise can either increase or decrease the coherency of background seismic noise for wind speeds above 6~m/s due to the interaction of wind with various surface objects. In comparison to the seismic noise at the Virgo site, the secondary microseism (0.2~Hz) noise level is higher in Gingin, but the seismic noise level between 1 and 10~Hz is lower due to the sparse population and absence of nearby road traffic.

astro-ph.IM↗

arXiv2022

Low coherency of wind induced seismic noise: Implications for gravitational wave detection

Seismic noise poses challenges for gravitational wave detection. Effective vibration isolation and methods to subtract unsheildable Newtonian Noise are examples. Seismic arrays offer one way to deal with these issues assuming seismic coherency. In this paper we find that wind induced seismic noise is incoherent and will dramatically reduce the projected low frequency sensitivity of future gravitational wave detectors. To quantify this, we measure the coherence length of wind induced seismic noise from 0.06--20~Hz in three distinct locations: close to a building, among tall trees and in shrubs. We show that wind induced seismic noise is ubiquitous and reduces the coherence lengths form several hundred meters to 2--40~m for 0.06--0.1~Hz, from $>$60~m to 3--16~m for 1.5--2.5~Hz and from $>$35~m to 1--16~m around 16.6 Hz frequency bands in the study area. This leads to significant loss of velocity and angular resolution of the array for primary microseism, 5 times worse Newtonian Noise cancellation by wiener filtering at 2~Hz, while it does not pose additional challenge for Newtonian Noise cancellation between 10--20~Hz.

physics.geo-ph↗

arXiv2022

Demonstration of Parametric Instability suppression through optical feedback

We demonstrate the suppression of parametric instability using through optical actuation in an electro-optical feedback loop, stabilising the high order optical mode content in an 80 metre long Fabry-Perot cavity. The loop suppression of the high order mode is achieved by injecting a high order mode with the same frequency and opposite phase. Frequency matching is achieved by measuring the beat note signal between the fundamental and high order mode in transmission of the cavity and applying that signal to an electro-optical modulator to create the required frequency sideband. Spatial mode matching of the sideband to the high order mode is accomplished through the inherent mode overlap between the input injected beam and the high order mode of the cavity. The paper presents the theoretical analysis and experimental demonstration of parametric instability suppression, for an instability which would normally ring up with a parametric gain of approximately 2.5.

physics.optics↗

arXiv2022

Observing the optical modes of parametric instability

Parametric Instability (PI) is a phenomenon that results from resonant interactions between optical and acoustic modes of a laser cavity. This is problematic in gravitational wave interferometers where the high intra-cavity power and low mechanical loss mirror suspension systems create an environment where three mode PI will occur without intervention. We demonstrate a technique for real time imaging of the amplitude and phase of the optical modes of PI yielding the first ever images of this phenomenon which could form part of active control strategies for future detectors.

physics.optics↗

arXiv2020

Ground Based Gravitational Wave Astronomy in the Asian Region

The current gravitational wave detectors have identified a surprising population of heavy stellar mass black holes, and an even larger population of coalescing neutron stars. The first observations have led to many dramatic discoveries and the confirmation of general relativity in very strong gravitational fields. The future of gravitational wave astronomy looks bright, especially if additional detectors with greater sensitivity, broader bandwidth, and better global coverage can be implemented. The first discoveries add impetus to gravitational wave detectors designed to detect in the nHz, mHz and kHz frequency bands. This paper reviews the century-long struggle that led to the recent discoveries, and reports on designs and possibilities for future detectors. The benefits of future detectors in the Asian region are discussed, including analysis of the benefits of a detector located in Australia.

gr-qc↗

arXiv2019

The US Program in Ground-Based Gravitational Wave Science: Contribution from the LIGO Laboratory

Recent gravitational-wave observations from the LIGO and Virgo observatories have brought a sense of great excitement to scientists and citizens the world over. Since September 2015,10 binary black hole coalescences and one binary neutron star coalescence have been observed. They have provided remarkable, revolutionary insight into the "gravitational Universe" and have greatly extended the field of multi-messenger astronomy. At present, Advanced LIGO can see binary black hole coalescences out to redshift 0.6 and binary neutron star coalescences to redshift 0.05. This probes only a very small fraction of the volume of the observable Universe. However, current technologies can be extended to construct "$3^\mathrm{rd}$ Generation" (3G) gravitational-wave observatories that would extend our reach to the very edge of the observable Universe. The event rates over such a large volume would be in the hundreds of thousands per year (i.e.tens per hour). Such 3G detectors would have a 10-fold improvement in strain sensitivity over the current generation of instruments, yielding signal-to-noise ratios of 1000 for events like those already seen. Several concepts are being studied for which engineering studies and reliable cost estimates will be developed in the next 5 years.

astro-ph.IM↗

arXiv2018

Angular instability in high optical power suspended cavities

Advanced gravitational wave detectors use suspended test masses to form optical resonant cavities for enhancing the detector sensitivity. These cavities store hundreds of kilowatts of coherent light and even higher optical power for future detectors. With such high optical power, the radiation pressure effect inside the cavity creates sufficiently strong coupling between test masses whose dynamics are significantly altered. The dynamics of two independent nearly free masses become a coupled mechanical resonator system. The transfer function of the local control system used for controlling the test masses is modified by the radiation pressure effect. The changes in the transfer function of the local control systems can result in a new type of angular instability which occurs at only 1.3 \% of the Sidles-Sigg instability threshold power. We report experimental results on a 74~m suspended cavity with a few kilowatts of circulating power, for which the power to mass ratio is comparable to the current Advanced LIGO. The radiation pressure effect on the test masses behaves like an additional optical feedback with respect to the local angular control, potentially making the mirror control system unstable. When the local angular control system is optimized for maximum stability margin, the instability threshold power increases from 4~kW to 29~kW. The system behavior is consistent with our simulation and the power dependent evolution of both the cavity soft and hard mode is observed. We show that this phenomenon is likely to significantly affect proposed gravitational wave detectors that require very high optical power.

astro-ph.IM↗

arXiv2017

Thermal modelling of Advanced LIGO test masses

High-reflectivity fused silica mirrors are at the epicentre of current advanced gravitational wave detectors. In these detectors, the mirrors interact with high power laser beams. As a result of finite absorption in the high reflectivity coatings the mirrors suffer from a variety of thermal effects that impact on the detectors performance. We propose a model of the Advanced LIGO mirrors that introduces an empirical term to account for the radiative heat transfer between the mirror and its surroundings. The mechanical mode frequency is used as a probe for the overall temperature of the mirror. The thermal transient after power build-up in the optical cavities is used to refine and test the model. The model provides a coating absorption estimate of 1.5 to 2.0 ppm and estimates that 0.3 to 1.3 ppm of the circulating light is scattered on to the ring heater.

astro-ph.IM↗

arXiv2016

First Demonstration of Electrostatic Damping of Parametric Instability at Advanced LIGO

Interferometric gravitational wave detectors operate with high optical power in their arms in order to achieve high shot-noise limited strain sensitivity. A significant limitation to increasing the optical power is the phenomenon of three-mode parametric instabilities, in which the laser field in the arm cavities is scattered into higher order optical modes by acoustic modes of the cavity mirrors. The optical modes can further drive the acoustic modes via radiation pressure, potentially producing an exponential buildup. One proposed technique to stabilize parametric instability is active damping of acoustic modes. We report here the first demonstration of damping a parametrically unstable mode using active feedback forces on the cavity mirror. A 15,538 Hz mode that grew exponentially with a time constant of 182 sec was damped using electro-static actuation, with a resulting decay time constant of 23 sec. An average control force of 0.03 nNrms was required to maintain the acoustic mode at its minimum amplitude.

physics.ins-det↗

arXiv2016

Analytical model for ring heater thermal compensation in the Advanced Laser Interferometer Gravitational-wave Observatory

Advanced laser interferometer gravitational-wave detectors use high laser power to achieve design sensitivity. A small part of this power is absorbed in the interferometer cavity mirrors where it creates thermal lenses, causing aberrations in the main laser beam that must be minimized by the actuation of "ring heaters," which are additional heater elements that are aimed to reduce the temperature gradients in the mirrors. In this article we derive the first, to the best of our knowledge, analytical model of the temperature field generated by an ideal ring heater. We express the resulting optical aberration contribution to the main laser beam in this axisymmetric case. Used in conjunction with wavefront measurements, our model provides a more complete understanding of the thermal state of the cavity mirrors and will allow a more efficient use of the ring heaters in the Advanced Laser Interferometer Gravitational-wave Observatory.

astro-ph.IM↗

arXiv2015

Parametric Instability in Long Optical Cavities and Suppression by Dynamic Transverse Mode Frequency Modulation

Three mode parametric instability has been predicted in Advanced gravitational wave detectors. Here we present the first observation of this phenomenon in a large scale suspended optical cavity designed to be comparable to those of advanced gravitational wave detectors. Our results show that previous modelling assumptions that transverse optical modes are stable in frequency except for frequency drifts on a thermal deformation time scale is unlikely to be valid for suspended mass optical cavities. We demonstrate that mirror figure errors cause a dependence of transverse mode offset frequency on spot position. Combined with low frequency residual motion of suspended mirrors, this leads to transverse mode frequency modulation which suppresses the effective parametric gain. We show that this gain suppression mechanism can be enhanced by laser spot dithering or fast thermal modulation. Using Advanced LIGO test mass data and thermal modelling we show that gain suppression factors of 10-20 could be achieved for individual modes, sufficient to greatly ameliorate the parametric instability problem.

physics.optics↗

arXiv2013

Radiation pressure excitation of test mass ultrasonic modes via three mode opto-acoustic interactions in a suspended Fabry-Perot cavity

Three-mode parametric-instabilities risk stable operation of gravitational-wave detectors. Instabilities occur through time varying radiation-pressure distributions, derived from beating between two optical modes, exciting mirror acoustic modes in Fabry-Perot cavities. Here we report the first demonstration of radiation-pressure driving of ultrasonic-acoustic modes via pairs of optical modes in gravitational-wave type optical cavities. In this experiment ~0.4W of TEM01 mode and ~1kW of TEM00 mode circulated inside the cavity, an ~181.6kHz excitation was observed with amplitude ~5E-13m. The results verify the driving force term in Braginsky's parametric instability feedback model. The interaction parametric gain was (3.8+/-0.5)E-3 and mass-ratio scaled opto-acoustic overlap 2.7+/-0.4.

physics.optics↗