arXiv subjects

Bikshapathi Gouda

Publications and source records attributed to Bikshapathi Gouda.

16 recordsLinked to original sources

arXiv2026

Over-the-Air Beamforming Design for Full-Duplex Cell-Free Massive MIMO Systems

We study a full-duplex (FD) cell-free massive MIMO system where distributed access points (APs) operate in FD mode while user equipments (UEs) remain half-duplex. Although simultaneous uplink (UL) and downlink (DL) transmissions improve spectral efficiency, they introduce residual self-interference, AP-to-AP coupling, and UE-to-UE cross-link interference. Building on prior over-the-air distributed beamforming frameworks, we develop a fully distributed beamforming design based on iterative UL and DL pilot signaling under a joint UL and DL sum mean-square error criterion that explicitly accounts for these interference components. In FD operation, simultaneous UL and DL pilot transmissions cause UE-to-UE pilot leakage, which contaminates the reconstruction of the cross terms required for AP-specific beamforming design. To mitigate this effect, we introduce a pilot-domain projection of the received signals at the UEs, which suppresses the interference component and enables accurate cross-term reconstruction at the APs. In addition, best-response updates at the UEs are employed within the alternating optimization framework to improve convergence under strong UE-to-UE interference. Numerical results demonstrate faster convergence and higher effective sum rate, with particularly significant gains for strongly interfering UEs, compared with both separate UL and DL distributed OTA beamforming training schemes and designs based solely on local channel state information.

eess.SP↗

arXiv2026

SEP Analysis of Quantized SIMO Systems with M-PSK over Correlated Fading Channels

The average symbol error probability (SEP) of a phase-quantized single-input multiple-output system with M-ary phase-shift keying modulation and maximum ratio combining (MRC) is analyzed under correlated Rayleigh fading and additive white Gaussian noise. Building on our prior framework for independent and identically distributed Rayleigh fading, we extend the analysis to the spatially correlated case by introducing an asymptotically equivalent MRC combiner that enables tractable SEP characterization. Using this approach, we derive closed-form expressions at high signal-to-noise ratio (SNR) that explicitly characterize the diversity and coding gains as functions of the receive correlation structure, phase-quantization resolution, and modulation order, up to a scaling factor bounded between 1 and 2. The results show that channel correlation primarily degrades the coding gain, leading to an SNR penalty, while the diversity gain is preserved when the channel covariance matrix is full-rank. The analytical findings are validated through Monte Carlo simulations, demonstrating a tight match across a wide SNR range.

eess.SP↗

arXiv2026

SEP Analysis of a Low-Resolution SIMO System with M-PSK over Fading Channels

In this paper, the average symbol error probability (SEP) of a phase-quantized single-input multiple-output (SIMO) system with M-ary phase-shift keying (PSK) modulation is analyzed under Rayleigh fading and additive white Gaussian noise. By leveraging a novel method, we derive exact SEP expressions for a quadrature PSK (QPSK)-modulated n-bit phase-quantized SIMO system with maximum ratio combining (SIMO-MRC), along with the corresponding high signal-to-noise ratio (SNR) characterizations in terms of diversity and coding gains. For a QPSK-modulated 2-bit phase-quantized SIMO system with selection combining, the diversity and coding gains are further obtained for an arbitrary number of receive antennas, complementing existing results. Interestingly, the proposed method also reveals a duality between a SIMO-MRC system and a phase-quantized multiple-input single-output (MISO) system with maximum ratio transmission, when the modulation order, phase-quantization resolution, antenna configuration, and the channel state information (CSI) conditions are reciprocal. This duality enables direct inference to obtain the diversity of a general M-PSK-modulated n-bit phase-quantized SIMO-MRC system, and extends the results to its MISO counterpart. All the above results have been obtained assuming perfect CSI at the receiver (CSIR). Finally, the SEP analysis of a QPSK-modulated 2-bit phase-quantized SIMO system is extended to the limited CSIR case, where the CSI at each receive antenna is represented by only 2 bits of channel phase information. In this scenario, the diversity gain is shown to be further halved in general.

eess.SP↗

arXiv2025

SEP Analysis of 1-Bit Quantized SIMO Systems with QPSK over Fading Channels

The average symbol error probability (SEP) of a 1-bit quantized single-input multiple-output (SIMO) system is analyzed under Rayleigh fading channels and quadrature phase-shift keying (QPSK) modulation. Previous studies have partially characterized the diversity gain for selection combining (SC). In this paper, leveraging a novel analytical method, an exact analytical SEP expression is derived for a 1-bit quantized SIMO system employing QPSK modulation at the transmitter and maximum ratio combining (MRC) at the receiver. The corresponding diversity and coding gains of a SIMO-MRC system are also determined. Furthermore, the diversity and coding gains of a 1-bit quantized SIMO-SC system are quantified for an arbitrary number of receive antennas, thereby extending and complementing prior results.

eess.SP↗

arXiv2025

Coordinated Multi-BS SSB Beam Design for Enhanced Initial Access Coverage

Ensuring strong synchronization signal block (SSB) coverage is essential for reliable user equipment (UE) connection during initial access. While techniques such as power boosting and network densification are commonly used, this work explores joint transmission (JT) of SSBs as an alternative to enhance coverage. Although JT is widely applied in data transmission, its use for SSBs has not been explored due to the lack of channel state information, which prevents coherent signal alignment across base stations (BSs). To address this, we propose a repetition-based JT strategy using a small set of predefined phase configurations at the BSs. This enables the UE to coherently combine multiple SSB receptions and achieve constructive gain regardless of its location. To reduce overhead, a limited number of joint beam configurations is selected to maximize the coverage. Simulation results under the line-of-sight conditions show up to 6 dB relative SNR gain with JT of SSBs using 4 BSs, compared to independent SSB transmission under the same resource budget. These results highlight the potential of JT to improve the coverage of SSBs during the initial access.

eess.SP↗

arXiv2025

Near-Field MIMO Channel Acquisition: Geometry-Aided Feedback and Transmission Design

Near-field (NF) line-of-sight (LoS) MIMO systems enable efficient channel state information (CSI) acquisition and precoding by exploiting known antenna geometries at both the base station (BS) and user equipment (UE). This paper introduces a compact parameterization of the NF LoS MIMO channel using two angles of departure (AoDs) and a BS-UE relative rotation angle. The inclusion of the second AoD removes the need for fine-grained distance grids imposed by conventional NF channel parametrization. To address the user-specific uplink pilot overhead in multiuser NF CSI acquisition, we propose a scheme that uses a fixed, UE-independent set of downlink pilots transmitted from a carefully selected subset of BS antennas. In dominant LoS conditions, as few as four pilots suffice, with Cram\'er-Rao bound (CRB) analysis confirming that increased antenna spacing improves estimation accuracy. Each UE estimates and quantizes its angular parameters and feeds them back to the BS for geometry-based CSI reconstruction, eliminating the need for full channel feedback. To enhance robustness against noise, quantization errors, and non-line-of-sight (NLoS) components, we introduce a two-stage precoding method. The initial precoding is computed from estimated LoS CSI and refined through bidirectional over-the-air (OTA) training. Furthermore, a two-step stream allocation strategy reduces pilot and computational overhead. Simulations demonstrate that the proposed approach achieves high data rates with significantly fewer OTA iterations, approaching the performance of perfect CSI.

eess.SP↗

arXiv2025

Data-Aided Regularization of Direct-Estimate Combiner in Distributed MIMO Systems

This paper explores the data-aided regularization of the direct-estimate combiner in the uplink of a distributed multiple-input multiple-output system. The network-wide combiner can be computed directly from the pilot signal received at each access point, eliminating the need for explicit channel estimation. However, the sample covariance matrix of the received pilot signal that is used in its computation may significantly deviate from the actual covariance matrix when the number of pilot symbols is limited. To address this, we apply a regularization to the sample covariance matrix using a shrinkage coefficient based on the received data signal. Initially, the shrinkage coefficient is determined by minimizing the difference between the sample covariance matrices obtained from the received pilot and data signals. Given the limitations of this approach in interference-limited scenarios, the shrinkage coefficient is iteratively optimized using the sample mean squared error of the hard-decision symbols, which is more closely related to the actual system's performance, e.g., the symbol error rate (SER). Numerical results demonstrate that the proposed regularization of the direct-estimate combiner significantly enhances the SER, particularly when the number of pilot symbols is limited.

eess.SP↗

arXiv2024

Uplink Transmit Power Optimization for Distributed Massive MIMO Systems with 1-Bit ADCs

This paper addresses the problem of uplink transmit power optimization in distributed massive multiple-input multiple-output systems, where remote radio heads (RRHs) are equipped with 1-bit analog-to-digital converters (ADCs). First, in a scenario where a single RRH serves a single user equipment (UE), the signal-to-noise-and-distortion ratio (SNDR) is shown to be a non-monotonic and unimodal function of the UE transmit power due to the quantization distortion (QD). Upon the introduction of multiple RRHs, adding properly tuned dithering at each RRH is shown to render the SNDR at the output of the joint receiver unimodal. In a scenario with multiple RRHs and UEs, considering the non-monotonic nature of the signal-to-interference-plus-noise-and-distortion ratio (SINDR), both the UE transmit powers and the RRH dithering levels are jointly optimized subject to the min-power and max-min-SINDR criteria, while employing Bussgang-based maximum ratio combining (BMRC) and minimum mean squared error (BMMSE) receivers. To this end, gradient and block coordinate descent methods are introduced to tune the UE transmit powers, whereas a line search coupled with gradient updates is used to adjust the RRH dithering levels. Numerical results demonstrate that jointly optimizing the UE transmit power and the RRH dithering levels can significantly enhance the system performance, thus facilitating joint reception from multiple RRHs across a range of scenarios. Comparing the BMMSE and BMRC receivers, the former offers a better interference and QD alleviation while the latter has a lower computational complexity.

eess.SP↗

arXiv2024

Combined DL-UL Distributed Beamforming Design for Cell-Free Massive MIMO

We consider a cell-free massive multiple-input multiple-output system with multi-antenna access points (APs) and user equipments (UEs), where the UEs can be served in both the downlink (DL) and uplink (UL) within a resource block. We tackle the combined optimization of the DL precoders and combiners at the APs and DL UEs, respectively, together with the UL combiners and precoders at the APs and UL UEs, respectively. To this end, we propose distributed beamforming designs enabled by iterative bi-directional training (IBT) and based on the minimum mean squared error criterion. To reduce the IBT overhead and thus enhance the effective DL and UL rates, we carry out the distributed beamforming design by assuming that all the UEs are served solely in the DL and then utilize the obtained beamformers for the DL and UL data transmissions after proper scaling. Numerical results show the superiority of the proposed combined DL-UL distributed beamforming design over separate DL and UL designs, especially with short resource blocks.

cs.IT↗

arXiv2023

Pilot-Based Uplink Power Control in Single-UE Massive MIMO Systems With 1-Bit ADCs

We propose uplink power control (PC) methods for massive multiple-input multiple-output systems with 1-bit analog-to-digital converters, which are specifically tailored to address the non-monotonic data detection performance with respect to the transmit power of the user equipment (UE). Considering a single UE, we design a multi-amplitude pilot sequence to capture the aforementioned non-monotonicity, which is utilized at the base station to derive UE transmit power adjustments via single-shot or differential power control (DPC) techniques. Both methods enable closed-loop uplink PC using different feedback approaches. The single-shot method employs one-time multi-bit feedback, while the DPC method relies on continuous adjustments with 1-bit feedback. Numerical results demonstrate the superiority of the proposed schemes over conventional closed-loop uplink PC techniques.

eess.SP↗

arXiv2023

Uplink Power Control for Distributed Massive MIMO with 1-Bit ADCs

We consider the problem of uplink power control for distributed massive multiple-input multiple-output systems where the base stations (BSs) are equipped with 1-bit analog-to-digital converters (ADCs). The scenario with a single-user equipment (UE) is first considered to provide insights into the signal-tonoise-and-distortion ratio (SNDR). With a single BS, the SNDR is a unimodal function of the UE transmit power. With multiple BSs, the SNDR at the output of the joint combiner can be made unimodal by adding properly tuned dithering at each BS. As a result, the UE can be effectively served by multiple BSs with 1-bit ADCs. Considering the signal-to-interference-plus-noise-anddistortion ratio (SINDR) in the multi-UE scenario, we aim at optimizing the UE transmit powers and the dithering at each BS based on the min-power and max-min-SINDR criteria. To this end, we propose three algorithms with different convergence and complexity properties. Numerical results show that, if the desired SINDR can only be achieved via joint combining across multiple BSs with properly tuned dithering, the optimal UE transmit power is imposed by the distance to the farthest serving BS (unlike in the unquantized case). In this context, dithering plays a crucial role in enhancing the SINDR, especially for UEs with significant path loss disparity among the serving BSs.

cs.IT↗

arXiv2022

Pilot-Aided Distributed Multi-Group Multicast Precoding Design for Cell-Free Massive MIMO

We propose fully distributed multi-group multicast precoding designs for cell-free massive multiple-input multiple-output (MIMO) systems with modest training overhead. We target the minimization of the sum of the maximum mean squared errors (MSEs) over the multicast groups, which is then approximated with a weighted sum MSE minimization to simplify the computation and signaling. To design the joint network-wide multi-group multicast precoders at the base stations (BSs) and the combiners at the user equipments (UEs) in a fully distributed fashion, we adopt an iterative bi-directional training scheme with UE-specific or group-specific precoded uplink pilots and group-specific precoded downlink pilots. To this end, we introduce a new group-specific uplink training resource that entirely eliminates the need for backhaul signaling for the channel state information (CSI) exchange. The precoders are optimized locally at each BS by means of either best-response or gradient-based updates, and the convergence of the two approaches is analyzed with respect to the centralized implementation with perfect CSI. Finally, numerical results show that the proposed distributed methods greatly outperform conventional cell-free massive MIMO precoding designs that rely solely on local CSI.

cs.IT↗

arXiv2022

Distributed Precoding Design for Multi-Group Multicasting in Cell-Free Massive MIMO

We consider multi-group multicast precoding designs for cell-free massive multiple-input multiple-output (MIMO) systems. To optimize the transmit and receive beamforming strategies, we focus on minimizing the sum of the maximum mean squared errors (MSEs) over the multicast groups, which is then approximated with the sum MSE to simplify the computation and signaling. We adopt an iterative bi-directional training scheme with uplink and downlink precoded pilots to cooperatively design the multi-group multicast precoders at each base station and the combiners at each user equipment in a distributed fashion. An additional group-specific uplink training resource is introduced, which entirely eliminates the need for backhaul signaling for channel state information (CSI) exchange. We also propose a simpler distributed precoding design based solely on group-specific pilots, which can be useful in the case of scarce training resources. Numerical results show that the proposed distributed methods greatly outperform conventional cell-free massive MIMO precoding designs that rely solely on local CSI.

cs.IT↗

arXiv2021

Joint Minimum DL-UL Rate Maximization for Cell-Free Massive MIMO

In cell-free massive multiple-input multiple-output (MIMO) systems, the beamforming strategies at the base stations (BSs) and user equipments (UEs) can be computed building on bi-directional training. However, the precoding/decoding optimization in the downlink (DL) and in the uplink (UL) generally requires two separate bi-directional training phases, which can be wasteful in the case of short scheduling blocks. This paper proposes a framework to reduce the bi-directional training overhead by considering a common beamforming training strategy for both DL and UL when the UEs to be served in the two directions are the same. In doing so, we consider the problem of maximizing the (weighted) minimum DL-UL rate among all the UEs. Numerical results show that, in scenarios with short scheduling blocks, the proposed framework outperforms the case where the DL and UL beamforming strategies are computed individually via two separate bi-directional training phases thanks to the reduced training overhead. Even more substantial gains are observed with respect to the case with a single bi-directional training phase, where the DL (resp. UL) beamforming strategies are reused in the UL (resp. DL).

eess.SP↗

arXiv2021

Low-complexity Multicast Beamforming for Multi-stream Multi-group Communications

In this paper, assuming multi-antenna transmitter and receivers, we consider multicast beamformer design for the weighted max-min-fairness (WMMF) problem in a multi-stream multi-group communication setup. Unlike the single-stream scenario, the WMMF objective in this setup is not equivalent to maximizing the minimum weighted SINR due to the summation over the rates of multiple streams. Therefore, the non-convex problem at hand is first approximated with a convex one and then solved using Karush-Kuhn-Tucker (KKT) conditions. Then, a practically appealing closed-form solution is derived, as a function of dual variables, for both transmit and receive beamformers. Finally, we use an iterative solution based on the sub-gradient method to solve for the mutually coupled and interdependent dual variables. The proposed solution does not rely on generic solvers and does not require any bisection loop for finding the achievable rate of various streams. As a result, it significantly outperforms the state-of-art in terms of computational cost and convergence speed.

cs.IT↗

arXiv2020

Distributed Precoding Design via Over-the-Air Signaling for Cell-Free Massive MIMO

Most works on cell-free massive multiple-input multiple-output (MIMO) consider non-cooperative precoding strategies at the base stations (BSs) to avoid extensive channel state information (CSI) exchange via backhaul signaling. However, considerable performance gains can be accomplished by allowing coordination among the BSs. This paper proposes the first distributed framework for cooperative precoding design in cell-free massive MIMO (and, more generally, in joint transmission coordinated multi-point) systems that entirely eliminates the need for backhaul signaling for CSI exchange. A novel over-the-air (OTA) signaling mechanism is introduced such that each BS can obtain the same cross-term information that is traditionally exchanged among the BSs via backhaul signaling. The proposed distributed precoding design enjoys desirable flexibility and scalability properties, as the amount of OTA signaling does not scale with the number of BSs or user equipments. Numerical results show fast convergence and remarkable performance gains as compared with non-cooperative precoding design. The proposed scheme can also outperform the centralized precoding design under realistic CSI acquisition.

cs.IT↗