arXiv Science⌕ Search

arXiv subjects

Benno List

Publications and source records attributed to Benno List.

At least 19 recordsLinked to original sources
arXiv2025

ILC250 Cost Update -- 2024

The International Linear Collider was conceived as a global project for an energy-frontier electron-positron collider.It employs superconducting RF and nano-beam technologies with a center-of-mass energy of 500 GeV. Its cost was estimated in 2013, based on the Technical Design Report published in 2013.Japan's high-energy community proposed to host the ILC in Japan as a Higgs boson factory at 250 GeV in its first phase, and a revised cost estimate was conducted in 2017 to host it in Japan. However, due to global price increases and currency fluctuations that emerged afterward, the 2017 estimate is now outdated. A new cost evaluation has therefore been performed, according for global inflation tends, exchange rate shifts, and recent experiences in SRF based accelerators. This report describes the cost update performed in 2024. The cost update is included in the ILC Status Report in May 2025, contributing to the ongoing 2026 update of the European Strategy for Particle Physics.

physics.acc-ph↗
arXiv2025

HALHF: a hybrid, asymmetric, linear Higgs factory using plasma- and RF-based acceleration

HALHF is a hybrid linear collider that uses electron-driven plasma-wakefield acceleration to accelerate electrons to high energy while using radio-frequency cavity technology to accelerate positrons. The most cost-effective solution collides low-energy positrons with high-energy electrons, producing a boost to the final state in the electron direction with $\gamma= 1.67$. The current HALHF baseline design produces a luminosity comparable to that of the baseline ILC but with a greatly reduced construction and carbon footprint and hence much lower cost than the mature linear-collider designs ILC and CLIC. Costs for HALHF are evaluated, together with that for the approximate 15-year R\&D programme necessary to realise HALHF. Time scales and cost for the R\&D are estimated. Upgrade paths for HALHF technology from a 250~GeV Higgs factory, through 380 and 550~GeV, up to 10~TeV are sketched.

physics.acc-ph↗
arXiv2025

Proceedings of the Erice Workshop: A new baseline for the hybrid, asymmetric, linear Higgs factory HALHF

The HALHF collaboration has discussed a new baseline for the project, taking into account comments from the accelerator community on various aspects of the original design. In particular, these concerned the practicality of the dual-purpose linac to accelerate both colliding positron bunches and the drive beams required for the plasma linac. In addition, many other aspects of the project were also considered; the discussion and conclusions are documented in this paper. Finally, a new baseline is outlined that has been optimised and addresses several weaknesses in the original design, has higher luminosity, reduced centre-of-mass energy boost and additional features such as positron polarization as well as electron polarization. Although HALHF has become longer and more expensive, it remains significantly smaller and cheaper than other mature Higgs factory designs currently under discussion.

physics.acc-ph↗
arXiv2024

Physics Performance and Detector Requirements at an Asymmetric Higgs Factory

The Hybrid Asymmetric Linear Higgs Factory (HALHF) proposes a shorter and cheaper design for a future Higgs factory. It reaches a $\sqrt{s} = 250$ GeV using a 500 GeV electron beam accelerated by an electron-driven plasma wake-field, and a conventionally-accelerated 31 GeV positron beam. Assuming plasma acceleration R&D challenges are solved in a timely manner, the asymmetry of the collisions brings additional challenges regarding the detector and the physics analyses, from forward boosted topologies and beam backgrounds. This contribution will detail the impact of beam parameters on beam-induced backgrounds, and provide a first look at what modification compared to e.g. the ILD can improve the physics performance at such a facility. The studies will be benchmarked against some flagship Higgs Factory analyses for comparison.

hep-ex↗
arXiv2022

The International Linear Collider: Report to Snowmass 2021

The International Linear Collider (ILC) is on the table now as a new global energy-frontier accelerator laboratory taking data in the 2030s. The ILC addresses key questions for our current understanding of particle physics. It is based on a proven accelerator technology. Its experiments will challenge the Standard Model of particle physics and will provide a new window to look beyond it. This document brings the story of the ILC up to date, emphasizing its strong physics motivation, its readiness for construction, and the opportunity it presents to the US and the global particle physics community.

physics.acc-ph↗
arXiv2019

The International Linear Collider: A Global Project

The International Linear Collider (ILC) is now under consideration as the next global project in particle physics. In this report, we review of all aspects of the ILC program: the physics motivation, the accelerator design, the run plan, the proposed detectors, the experimental measurements on the Higgs boson, the top quark, the couplings of the W and Z bosons, and searches for new particles. We review the important role that polarized beams play in the ILC program. The first stage of the ILC is planned to be a Higgs factory at 250 GeV in the centre of mass. Energy upgrades can naturally be implemented based on the concept of a linear collider. We discuss in detail the ILC program of Higgs boson measurements and the expected precision in the determination of Higgs couplings. We compare the ILC capabilities to those of the HL-LHC and to those of other proposed e+e- Higgs factories. We emphasize throughout that the readiness of the accelerator and the estimates of ILC performance are based on detailed simulations backed by extensive RandD and, for the accelerator technology, operational experience.

hep-ex↗
arXiv2019

The International Linear Collider. A European Perspective

The International Linear Collider (ILC) being proposed in Japan is an electron-positron linear collider with an initial energy of 250 GeV. The ILC accelerator is based on the technology of superconducting radio-frequency cavities. This technology has reached a mature stage in the European XFEL project and is now widely used. The ILC will start by measuring the Higgs properties, providing high-precision and model-independent determinations of its parameters. The ILC at 250 GeV will also search for direct new physics in exotic Higgs decays and in pair-production of weakly interacting particles. The use of polarised electron and positron beams opens new capabilities and scenarios that add to the physics reach. The ILC can be upgraded to higher energy, enabling precision studies of the top quark and measurement of the top Yukawa coupling and the Higgs self-coupling. The international -- including European -- interest for the project is very strong. Europe has participated in the ILC project since its early conception and plays a major role in its present development covering most of its scientific and technological aspects: physics studies, accelerator and detectors. The potential for a wide participation of European groups and laboratories is thus high, including important opportunities for European industry. Following decades of technical development, R&D, and design optimisation, the project is ready for construction and the European particle physics community, technological centers and industry are prepared to participate in this challenging endeavour.

hep-ex↗
arXiv2019

The International Linear Collider. A Global Project

A large, world-wide community of physicists is working to realise an exceptional physics program of energy-frontier, electron-positron collisions with the International Linear Collider (ILC). This program will begin with a central focus on high-precision and model-independent measurements of the Higgs boson couplings. This method of searching for new physics beyond the Standard Model is orthogonal to and complements the LHC physics program. The ILC at 250 GeV will also search for direct new physics in exotic Higgs decays and in pair-production of weakly interacting particles. Polarised electron and positron beams add unique opportunities to the physics reach. The ILC can be upgraded to higher energy, enabling precision studies of the top quark and measurement of the top Yukawa coupling and the Higgs self-coupling. The key accelerator technology, superconducting radio-frequency cavities, has matured. Optimised collider and detector designs, and associated physics analyses, were presented in the ILC Technical Design Report, signed by 2400 scientists. There is a strong interest in Japan to host this international effort. A detailed review of the many aspects of the project is nearing a conclusion in Japan. Now the Japanese government is preparing for a decision on the next phase of international negotiations, that could lead to a project start within a few years. The potential timeline of the ILC project includes an initial phase of about 4 years to obtain international agreements, complete engineering design and prepare construction, and form the requisite international collaboration, followed by a construction phase of 9 years.

hep-ex↗
arXiv2013

The International Linear Collider Technical Design Report - Volume 3.II: Accelerator Baseline Design

The International Linear Collider Technical Design Report (TDR) describes in four volumes the physics case and the design of a 500 GeV centre-of-mass energy linear electron-positron collider based on superconducting radio-frequency technology using Niobium cavities as the accelerating structures. The accelerator can be extended to 1 TeV and also run as a Higgs factory at around 250 GeV and on the Z0 pole. A comprehensive value estimate of the accelerator is give, together with associated uncertainties. It is shown that no significant technical issues remain to be solved. Once a site is selected and the necessary site-dependent engineering is carried out, construction can begin immediately. The TDR also gives baseline documentation for two high-performance detectors that can share the ILC luminosity by being moved into and out of the beam line in a "push-pull" configuration. These detectors, ILD and SiD, are described in detail. They form the basis for a world-class experimental programme that promises to increase significantly our understanding of the fundamental processes that govern the evolution of the Universe.

physics.acc-ph↗
arXiv2013

The International Linear Collider Technical Design Report - Volume 3.I: Accelerator R&D in the Technical Design Phase

The International Linear Collider Technical Design Report (TDR) describes in four volumes the physics case and the design of a 500 GeV centre-of-mass energy linear electron-positron collider based on superconducting radio-frequency technology using Niobium cavities as the accelerating structures. The accelerator can be extended to 1 TeV and also run as a Higgs factory at around 250 GeV and on the Z0 pole. A comprehensive value estimate of the accelerator is give, together with associated uncertainties. It is shown that no significant technical issues remain to be solved. Once a site is selected and the necessary site-dependent engineering is carried out, construction can begin immediately. The TDR also gives baseline documentation for two high-performance detectors that can share the ILC luminosity by being moved into and out of the beam line in a "push-pull" configuration. These detectors, ILD and SiD, are described in detail. They form the basis for a world-class experimental programme that promises to increase significantly our understanding of the fundamental processes that govern the evolution of the Universe.

physics.acc-ph↗
arXiv2010

Consideration of Photon Radiation in Kinematic Fits for Future e+ e- Colliders

Kinematic fitting is an important tool to improve the resolution in high-energy physics experiments. At future e+e- colliders, photon radiation parallel to the beam carrying away large amounts of energy and momentum will become a challenge for kinematic fitting. A photon with longitudinal momentum pz(η) is introduced, which is parametrized such that η follows a normal distribution. In the fit, η is treated as having a measured value of zero, which corresponds to pz = 0. As a result, fits with constraints on energy and momentum conservation converge well even in the presence of a highly energetic photon, while the resolution of fits without such a photon is retained. A fully simulated and reconstructed e+e- -> qqqq event sample at sqrt(s) = 500 GeV is used to investigate the performance of this method under realistic conditions, as expected at the International Linear Collider.

hep-ex↗
arXiv2010

Treatment of Photon Radiation in Kinematic Fits at Future e+ e- Colliders

Kinematic fitting, where constraints such as energy and momentum conservation are imposed on measured four-vectors of jets and leptons, is an important tool to improve the resolution in high-energy physics experiments. At future e+ e- colliders, photon radiation parallel to the beam carrying away large amounts of energy and momentum will become a challenge for kinematic fitting. A photon with longitudinal momentum p_z^γ(η) is introduced, which is parametrized such that η~follows a normal distribution. In the fit, η~is treated as having a measured value of zero, which corresponds to p_z^γ(η)=0. As a result, fits with constraints on energy and momentum conservation converge well even in the presence of a highly energetic photon, while the resolution of fits without such a photon is retained. A fully simulated and reconstructed e+ e- -> qqqq event sample at \sqrt{s}=500 GeV is used to investigate the performance of this method under realistic conditions, as expected at the International Linear Collider.

hep-ex↗
arXiv2009

A Measurement of Beauty Photoproduction Through Decays to Muons and Jets at HERA-II

The photoproduction of beauty quarks in ep collisions has been measured using a data sample of 170 pb^-1 collected with the H1 detector at HERA-II in the years 2006 and 2007. Events with two jets and a muon in the final state were investigated, and beauty events were identified using the muon's relative transverse momentum to a jet and its impact parameter. Visible cross sections were measured differentially in the transverse momenta of the highest energy jet (p_T^jet1) and the muon (pt_mu), the pseudorapidity of the muon (eta_mu) and of the photon's momentum fraction x_gamma entering the hard interaction. The measurements are found to be well described by QCD calculations at NLO.

hep-ex↗
arXiv2009

Extraction of the Pomeron Trajectory from a Global Fit to Exclusive $\rho^0$ Meson Photoproduction Data

Based on data on elastic $\rho^0$ photoproduction from the H1, Omega and ZEUS collaborations, a fit has been performed to extract the value $\alpha_P (t)$ of the pomeron trajectory at fixed values of t from the W dependence of the differential $\gamma p$ cross section $d \sigma_{\gamma p} (W) / d t$. The data used in the fit cover the range of $8.3 \le W \le 94 GeV$ in $\gamma p$ centre-of-mass energy and $0.01 \le |t| \le 0.95 GeV^2$ in momentum transfer. A linear fit to the resulting values of $\alpha_P (t)$ yields $\alpha_{P,0} =1.0871 \pm 0.0026 (stat.) \pm 0.0030 (syst.)$ for the intercept and $\alpha'_P = 0.126 \pm 0.013 (stat.) \pm 0.012 (syst.) GeV^{-2}$ for the slope of the pomeron trajectory. The data are also compatible with the Donnachie-Landshoff trajectory $\alpha_P (t) = 1.0808 + 0.25 GeV^{-2}\cdot t$ at low values $|t| \lesssim 0.3 GeV^2$ and with a constant value of $\alpha_P (t)$ at larger values of $|t|$.

hep-ex↗
arXiv2009

Kinematic Fitting in the Presence of ISR at the ILC

Kinematic fitting is a well-established tool to improve jet energy and invariant mass resolutions by fitting the measured values under constraints (e.g. energy conservation). However, in the presence of substantial ISR and Beamstrahlung, naive energy and (longitudinal) momentum constraints fail due to the a priori unknown amount of undetected momentum carried away by collinear photons. It is possible to take care of those two effects and thus obtain significantly higher mass resolutions.

hep-ex↗
arXiv2008

Charm and Beauty Photoproduction at HERA

After the completion of data taking at HERA-2, a large data set is at hand to study the photoproduction of charm and beauty quarks in ep collisions. New measurements of charm production based on D^* meson tagging and beauty production based on muon and electron reconstruction test perturbative QCD calculations with improved accuracy. In general, QCD calculations at NLO describe the data well. The scale uncertainties are, however, large and dominate over the experimental uncertainties, calling for more precise calculations.

hep-ex↗
arXiv2007

Summary of the Heavy Flavor Working Group

During the last year many important results have been achieved in heavy flavour physics: New measurements of charm and beauty production have been performed at HERA and the Tevatron. A wealth of new spectroscopy data with several new, unexpected states in the charmonium and the D_s systems has been collected and b to d gamma transitions have been established. The oscillation frequency in the B_s Bbar_s is now measured, and mixing in the D0 D0bar system has been observed. Theoretical progress in the areas of open heavy flavour production, quarkonium production and decays, and multiquark spectroscopy has been presented at this workshop.

hep-ph↗