arXiv subjects

Annika Robens-Radermacher

Publications and source records attributed to Annika Robens-Radermacher.

4 recordsLinked to original sources

arXiv2026

Buildability Assessment of 3D-Printed Concrete Structures Using Smoothed Mohr-Coulomb Plasticity with Isotropic Hardening

Extrusion-based 3D concrete printing builds structural elements layer upon layer without formwork, so freshly deposited material must carry the growing weight of the structure while it is still gaining strength and stiffness. The largest number of layers that can be printed before failure, the buildability, is therefore central to process design. Its prediction rests above all on how accurately the constitutive model represents fresh concrete. Existing finite element frameworks pair gradual pre-failure hardening only with smooth yield surfaces, which leaves the Mohr-Coulomb surface that best describes fresh concrete restricted to perfect plasticity. This work combines a smoothed Mohr-Coulomb yield surface with nonlinear isotropic hardening of the cohesion, formulated in an updated Lagrangian setting with an activation field for layer deposition. Failure is identified from a tangent-stiffness eigenvalue criterion that matches the analytical self-weight buckling load of a slender wall and is insensitive to geometric imperfection. The framework reproduces the measured collapse of a printed straight wall within one layer and predicts the collapse of a hollow cylinder closer to experiment than existing frameworks. A study over six diameters and six hardening rates shows buildability peaking at intermediate diameters and rising with the hardening rate. Recording how much of its strength the material has used at failure, slender cylinders fail with much still in reserve while intermediate ones use nearly all of it. The two failure modes are therefore identified as the limits of one process rather than separate failure mechanisms.

cs.CE↗

arXiv2026

Influence of Extruded Filament Shape on Buildability in 3D Concrete Printing: A Geometry-Informed Deep Learning-FEM Approach

The geometric morphology of deposited filaments can significantly influence the structural performance and stability of 3D concrete-printed (3DCP) structures. However, most finite element (FEM)-based approaches for buildability assessment represent printed layers as simplified rectangles, potentially limiting predictive accuracy. This study proposes a geometry-informed modelling framework that integrates the deep-learning-based filament shape prediction tool ShapeGen3DCP with a layer-activation FEM approach to investigate the effect of realistic filament geometries on buildability. The framework generates geometry-aware numerical models directly from material and process parameters, eliminating the need for experimental filament characterization or computationally intensive fluid-flow simulations. Validation against experimental data and a parametric study of rectilinear walls demonstrate that extrusion parameters and the resulting filament geometry can significantly influence buildability predictions. Realistic filament representations are particularly important for free-flow deposition, whereas layer-pressing strategies are less sensitive to geometric simplifications. Among the investigated representations, an elliptical approximation provides an effective balance between geometric fidelity and modelling simplicity. When rectangular representations are preferred to enable regular computational meshes for faster simulations, defining their dimensions based on volume conservation improves prediction reliability compared with calibrating them using either the maximum filament width or the interlayer contact width. Overall, the proposed methodology demonstrates the importance of incorporating filament geometry into 3DCP simulations and provides practical guidance for selecting efficient and accurate geometric representations for buildability assessment.

cs.CE↗

arXiv2026

Quantifying water-driven geometric uncertainties in powder bed concrete printing using high-resolution 3D modeling

Dimensional accuracy in powder bed 3D printing of concrete is strongly influenced by binder distribution, and the resulting geometric deviations can be direction-dependent. This study examines how voxel-wise water dosage influences geometric fidelity and deviation anisotropy. Experiments show that small changes in water content can cause large, systematic deviations, including edge rounding and swelling. We quantify these effects using high-resolution stereophotogrammetry, aligning as-built scans with CAD models. We then compute deviation metrics such as point-wise distance errors and volumetric differences across multiple water-dosage settings, revealing repeatable, directionally biased deformation patterns that intensify with higher water content. Mechanical testing indicates that stiffness and strength change only marginally, with no clear trend in the tested range. This is explained by excess voxel water diffusing into surrounding powder, leaving the effective water-cement ratio largely unchanged. Finally, we demonstrate a design-compensation concept that pre-adjusts digital geometry to counter predictable deviations, improving accuracy without post-processing.

cs.CE↗

arXiv2022

Multiscale modeling of linear elastic heterogeneous structures via localized model order reduction

In this paper, a methodology for fine scale modeling of large scale structures is proposed, which combines the variational multiscale method, domain decomposition and model order reduction. The influence of the fine scale on the coarse scale is modelled by the use of an additive split of the displacement field, addressing applications without a clear scale separation. Local reduced spaces are constructed by solving an oversampling problem with random boundary conditions. Herein, we inform the boundary conditions by a global reduced problem and compare our approach using physically meaningful correlated samples with existing approaches using uncorrelated samples. The local spaces are designed such that the local contribution of each subdomain can be coupled in a conforming way, which also preserves the sparsity pattern of standard finite element assembly procedures. Several numerical experiments show the accuracy and efficiency of the method, as well as its potential to reduce the size of the local spaces and the number of training samples compared to the uncorrelated sampling.

cs.CE↗