arXiv subjects

Aashish Sahu

Publications and source records attributed to Aashish Sahu.

3 recordsLinked to original sources

arXiv2026

Integrated Guidance and Control of a Mother-Child UAV-UGV System for Cooperative Missions

Autonomous recovery of a small multirotor onto a hovering multirotor carrier differs from recovery onto ground or shipborne platforms because the recovery surface is itself an actively controlled, thrust-limited aerial vehicle. This paper presents a field-validated autonomy framework for a heterogeneous rover-mothership-child system executing rover supervision, mothership transit, child deployment and sortie, autonomous return, aerial recovery, and synchronized descent. The recovery stack combines jerk-bounded reference generation, disturbance-observer-augmented planar tracking, feasibility-aware vertical control, a discrete-time barrier-based safety filter for relative vertical geometry, and communication-aware carrier-state prediction. The contribution is the coordinated system-level integration of these methods for recovery onto a hovering multirotor and its full-scale outdoor validation. The framework is implemented on a PX4-ROS 2 architecture using RTK-enabled GNSS, IMU, and barometric fusion, with mothership-side 1D lidar used only as an auxiliary near-contact cue. RTK-fixed positioning was maintained throughout testing. Across 20 outdoor cooperative missions, 17 successfully completed deployment, sortie, and recovery, giving an observed mission success rate of 85%. For successful recoveries, mean terminal-alignment time was 6.3 s, mean planar alignment error at acceptance was 0.18 m, maximum terminal planar deviation was 0.32 m within a 0.40 m capture radius, and minimum logged relative vertical separation during coupled descent was 0.41 m. Mothership planar station-keeping RMS error was 0.25 m. The three unsuccessful trials occurred at different mission stages and are analyzed separately. Results demonstrate practical autonomous aerial recovery within the tested outdoor operating envelope.

cs.RO↗

arXiv2026

RTK-Vision PPO for Autonomous Micro UAV Recovery on an Airborne Carrier

Autonomous recovery of a micro unmanned aerial vehicle (UAV) onto a moving airborne carrier enables reusable deploy-mission-recover operation, but couples long-range rendezvous, close-range perception, carrier motion, aerodynamic interaction, and a discontinuous contact event. This paper presents an RTK-vision-guided reinforcement-learning framework in which a child UAV is physically transported by a larger carrier, takes off from the carrier while airborne, executes an independent sortie, returns to the carrier's current position, redocks, and subsequently descends with the carrier. Both vehicles carry RTK-GNSS, and the carrier continuously shares its navigation state with the child. Near the recovery deck, RTK remains active while a downward-facing camera with a fiducial marker detector provides marker-relative alignment cues. A proximal policy optimization (PPO) policy governing the terminal recovery phase is trained in a physics-based MuJoCo simulation environment with explicit sensor noise models, an aerodynamic disturbance surrogate, and marker-latency randomization, then transferred to hardware. PX4 retains low-level stabilization, and a deterministic safety gate authorizes descent independently of the learned policy. The PPO checkpoint achieves 99.55% success over 2,000 held-out randomized terminal episodes, compared with 78.4% for a tuned PD baseline under identical conditions, with a median planar terminal error of 6.62 cm. Across 14 outdoor trials, the full mission succeeds in 13 trials (92.9%), spanning both near-region recovery and recovery after the carrier translates away from the release point. The results demonstrate a complete autonomous aerial deployment-and-recovery cycle rather than an isolated landing maneuver, establishing a practical basis for reusable carrier-child operation in inspection, surveillance, and mobile-logistics applications.

cs.RO↗

arXiv2026

Vision-Guided Morphing Quadcopter for Multi-Geometry Payload Transport through Narrow Passages

Aerial payload transport using multirotor unmanned aerial vehicles is challenging because payload geometry, contact interaction, grasp stability, flight control, and narrow-passage traversal are strongly coupled during pickup and transport. Object-specific grippers often cannot adapt their footprint or grasp geometry when the payload shape or passage width changes. This paper presents a vision-guided morphing quadcopter for multi-geometry payload transport through narrow passages. The proposed platform uses four hybrid arm-leg structures that function as both landing supports and grasping members. A centrally placed actuator drives a tendon-based morphing mechanism, enabling all four arms to synchronously retract or expand for object grasping, footprint reduction, and post-transport release. Onboard vision estimates the payload geometry and passage width, while endpoint force feedback is used to confirm grasp contact during payload engagement. A phase-wise mission planner, PID-based flight stabilization, and morphology-adaptive grasp controller are implemented in a MuJoCo simulation environment. The framework is evaluated using box, cylindrical, and spherical payloads, representing flat-faced, rolling-curved, and fully curved contact conditions. Across the three cases, the simulated system completes the pickup-transport-release sequence with a maximum RMS position error of 0.31 m, a final drop-zone error below 0.18 m, a compact grasp footprint of 0.09-0.21 m2, and a footprint reduction of 75.0-89.7 percent. The results demonstrate that a single-actuator morphing quadcopter can adapt its grasp footprint for the transport of payloads with different geometries while reducing its overall footprint for narrow-passage traversal.

cs.RO↗