arXiv subjects

A. Lechner

Publications and source records attributed to A. Lechner.

11 recordsLinked to original sources

arXiv2025

Decommissioning and Post-Irradiation Examination of the LHC Beam Dumps

The LHC beam dumps are responsible for the safe absorption of the Large Hadron Collider (LHC) particle beams. In 2018, the two 6.4-tonne beam dumps that had been in operation since the LHC's startup in 2008 were removed and replaced with upgraded versions. Endoscopic inspections of these beam dumps and experimental high-intensity proton-beam irradiation of material samples raised concerns about the structural integrity of the carbon-based materials in their cores. It was therefore decided to undertake an accelerated project of dismantling and post-irradiation examination of the removed dumps as part of a wider program of work to ensure the safe operation of the LHC beam dumps in the coming years. This paper describes the decommissioning process for the two beam dumps carried out at CERN between 2021 and 2023, covering the preparatory studies, practical challenges encountered, and solutions implemented. It details the establishment of an operational framework, including the preparation of the working environment, the development of a method for cutting the irradiated 12-mm-thick duplex stainless-steel vessel, and the cut sequencing. Additionally, the paper presents the findings derived from the post-irradiation examination of the different carbon-based core materials subjected to deposited energy densities up to 1.5 kJ/g. The extruded graphite plates within the vessel exhibited a cracking pattern, which was likely due to the dynamic response of the device upon beam impact, and their retaining rings were found to be displaced. Despite minor signs of surface deterioration, the expanded graphite sheets were intact, and the isostatic graphite blocks showed no evidence of material degradation.

physics.acc-ph↗

arXiv2023

Power deposition studies for standard and crystal-assisted heavy ion collimation inthe CERN Large Hadron Collider

The LHC heavy-ion program with $^{208}$Pb$^{82+}$ beams will benefit from a significant increase of the beam intensity when entering its High-Luminosity era in Run~3 (2023). The stored energy is expected to surpass 20~MJ per beam. The LHC is equipped with a betatron collimation system, which intercepts the transverse beam halo and protects sensitive equipment such as superconducting magnets against beam losses. However, nuclear fragmentation and electromagnetic dissociation of $^{208}$Pb$^{82+}$ ions in collimators generates a flux of secondary fragments, which are lost in downstream dispersion suppressor and arc cells. These secondary ions may pose a performance limitation in upcoming runs since they can induce magnet quenches. In order to mitigate this risk, an alternative collimation technique, relying on bent crystals as primary collimators, will be used in forthcoming heavy-ion runs. In this paper, we study the power deposition in superconducting magnets by means of tracking and \textsc{FLUKA} shower simulations, comparing the standard collimation system against the crystal-based one. In order to quantify the predictive ability of the simulation model, we present absolute benchmarks against beam loss monitor measurements from the 2018 $^{208}$Pb$^{82+}$ run at 6.37~$Z$TeV. The benchmarks cover several hundred meters of beamline, from the primary collimators to the first arc cells. Based on these studies, we provide a detailed analysis of ion fragmentation and leakage to the cold magnets and quantify the expected quench margin in future $^{208}$Pb$^{82+}$ runs.

physics.acc-ph↗

arXiv2021

Study of dust-induced beam losses in the cryogenic arcs of the CERN Large Hadron Collider

The interaction of dust particles with the LHC proton beams accounts for a major fraction of irregular beam loss events observed in LHC physics operation. The events cease after a few beam revolutions because of the expulsion of dust particles from the beam once they become ionized in the transverse beam tails. Despite the transient nature of these events, the resulting beam losses can trigger beam aborts or provoke quenches of superconducting magnets. In this paper, we study the characteristics of beam-dust particle interactions in the cryogenic arcs by reconstructing key observables like nuclear collision rates, loss durations and integral losses per event. The study is based on events recorded during 6.5 TeV operation with stored beam intensities of up to $\sim 3\times 10{^{14}}$ protons per beam. We show that inelastic collision rates can reach almost $10^{12}$ collisions per second, resulting in a loss of up to $\sim 1.6\times 10^{8}$ protons per event. We demonstrate that the experimental distributions and their dependence on beam parameters can be described quantitatively by a previously developed simulation model if dust particles are assumed to be attracted by the beam. The latter finding is consistent with recent time profile studies and yields further evidence that dust particles carry a negative charge when entering the beam. We also develop different hypotheses regarding the absence of higher-loss events in the measurements, although such events are theoretically not excluded by the simulation model. The results provide grounds for predicting dust-induced beam losses in presence of higher-intensity beams in future runs of the High-Luminosity LHC.

physics.acc-ph↗

arXiv2021

Design and behaviour of the Large Hadron Collider external beam dumps capable of receiving 539 MJ/dump

Two 6-t beam dumps, made of a graphite core encapsulated in a stainless steel vessel, are used to absorb the energy of the two Large Hadron Collider (LHC) intense proton beams during operation of the accelerator. Operational issues started to appear in 2015 during LHC Run 2 (2014-2018) as a consequence of the progressive increase of the LHC beam kinetic energy, necessitating technical interventions in the highly radioactive areas around the dumps. Nitrogen gas leaks appeared after highly energetic beam impacts and instrumentation measurements indicated an initially unforeseen movement of the dumps. A computer modelling analysis campaign was launched to understand the origin of these issues, including both Monte Carlo simulations to model the proton beam interaction as well as advanced thermo-mechanical analyses. The main findings were that the amount of instantaneous energy deposited in the dump vessel leads to a strong dynamic response of the whole dump and high accelerations (above 2000g). Based on these findings, an upgraded design, including a new support system and beam windows, was implemented to ensure the dumps' compatibility with the more intense beams foreseen during LHC Run 3 (2022-2025) of 539 MJ per beam. In this paper an integral overview of the operational behaviour of the dumps and the upgraded configurations are discussed.

physics.acc-ph↗

arXiv2019

Full Scale Proton Beam Impact Testing of new CERN Collimators and Validation of a Numerical Approach for Future Operation

New collimators are being produced at CERN in the framework of a large particle accelerator upgrade project to protect beam lines against stray particles. Their movable jaws hold low density absorbers with tight geometric requirements, while being able to withstand direct proton beam impacts. Such events induce considerable thermo-mechanical loads, leading to complex structural responses, which make the numerical analysis challenging. Hence, an experiment has been developed to validate the jaw design under representative conditions and to acquire online results to enhance the numerical models. Two jaws have been impacted by high-intensity proton beams in a dedicated facility at CERN and have recreated the worst possible scenario in future operation. The analysis of online results coupled to post-irradiation examinations have demonstrated that the jaw response remains in the elastic domain. However, they have also highlighted how sensitive the jaw geometry is to its mounting support inside the collimator. Proton beam impacts, as well as handling activities, may alter the jaw flatness tolerance value by $\pm$ 70 ${\mu}$m, whereas the flatness tolerance requirement is 200 ${\mu}$m. In spite of having validated the jaw design for this application, the study points out numerical limitations caused by the difficulties in describing complex geometries and boundary conditions with such unprecedented requirements.

physics.acc-ph↗

arXiv2017

Collimation System

Chapter 5 in High-Luminosity Large Hadron Collider (HL-LHC) : Preliminary Design Report. The Large Hadron Collider (LHC) is one of the largest scientific instruments ever built. Since opening up a new energy frontier for exploration in 2010, it has gathered a global user community of about 7,000 scientists working in fundamental particle physics and the physics of hadronic matter at extreme temperature and density. To sustain and extend its discovery potential, the LHC will need a major upgrade in the 2020s. This will increase its luminosity (rate of collisions) by a factor of five beyond the original design value and the integrated luminosity (total collisions created) by a factor ten. The LHC is already a highly complex and exquisitely optimised machine so this upgrade must be carefully conceived and will require about ten years to implement. The new configuration, known as High Luminosity LHC (HL-LHC), will rely on a number of key innovations that push accelerator technology beyond its present limits. Among these are cutting-edge 11-12 tesla superconducting magnets, compact superconducting cavities for beam rotation with ultra-precise phase control, new technology and physical processes for beam collimation and 300 metre-long high-power superconducting links with negligible energy dissipation. The present document describes the technologies and components that will be used to realise the project and is intended to serve as the basis for the detailed engineering design of HL-LHC.

physics.acc-ph↗

arXiv2017

Energy Deposition and Radiation to Electronics

Chapter 10 in High-Luminosity Large Hadron Collider (HL-LHC) : Preliminary Design Report. The Large Hadron Collider (LHC) is one of the largest scientific instruments ever built. Since opening up a new energy frontier for exploration in 2010, it has gathered a global user community of about 7,000 scientists working in fundamental particle physics and the physics of hadronic matter at extreme temperature and density. To sustain and extend its discovery potential, the LHC will need a major upgrade in the 2020s. This will increase its luminosity (rate of collisions) by a factor of five beyond the original design value and the integrated luminosity (total collisions created) by a factor ten. The LHC is already a highly complex and exquisitely optimised machine so this upgrade must be carefully conceived and will require about ten years to implement. The new configuration, known as High Luminosity LHC (HL-LHC), will rely on a number of key innovations that push accelerator technology beyond its present limits. Among these are cutting-edge 11-12 tesla superconducting magnets, compact superconducting cavities for beam rotation with ultra-precise phase control, new technology and physical processes for beam collimation and 300 metre-long high-power superconducting links with negligible energy dissipation. The present document describes the technologies and components that will be used to realise the project and is intended to serve as the basis for the detailed engineering design of HL-LHC.

physics.acc-ph↗

arXiv2017

Injection and Dumping Systems

Chapter 14 in High-Luminosity Large Hadron Collider (HL-LHC) : Preliminary Design Report. The Large Hadron Collider (LHC) is one of the largest scientific instruments ever built. Since opening up a new energy frontier for exploration in 2010, it has gathered a global user community of about 7,000 scientists working in fundamental particle physics and the physics of hadronic matter at extreme temperature and density. To sustain and extend its discovery potential, the LHC will need a major upgrade in the 2020s. This will increase its luminosity (rate of collisions) by a factor of five beyond the original design value and the integrated luminosity (total collisions created) by a factor ten. The LHC is already a highly complex and exquisitely optimised machine so this upgrade must be carefully conceived and will require about ten years to implement. The new configuration, known as High Luminosity LHC (HL-LHC), will rely on a number of key innovations that push accelerator technology beyond its present limits. Among these are cutting-edge 11-12 tesla superconducting magnets, compact superconducting cavities for beam rotation with ultra-precise phase control, new technology and physical processes for beam collimation and 300 metre-long high-power superconducting links with negligible energy dissipation. The present document describes the technologies and components that will be used to realise the project and is intended to serve as the basis for the detailed engineering design of HL-LHC.

physics.acc-ph↗

arXiv2015

Energy deposition studies for the High-Luminosity Large Hadron Collider inner triplet magnets

A detailed model of the High Luminosity LHC inner triplet region with new large-aperture Nb3Sn magnets, field maps, corrector packages, and segmented tungsten inner absorbers was built and implemented into the FLUKA and MARS15 codes. In the optimized configuration, the peak power density averaged over the magnet inner cable width is safely below the quench limit. For the integrated luminosity of 3000 fb-1, the peak dose in the innermost magnet insulator ranges from 20 to 35 MGy. Dynamic heat loads to the triplet magnet cold mass are calculated to evaluate the cryogenic capability. In general, FLUKA and MARS results are in a very good agreement.

physics.acc-ph↗

arXiv2015

Testing Beam-Induced Quench Levels of LHC Superconducting Magnets

In the years 2009-2013 the Large Hadron Collider (LHC) has been operated with the top beam energies of 3.5 TeV and 4 TeV per proton (from 2012) instead of the nominal 7 TeV. The currents in the superconducting magnets were reduced accordingly. To date only seventeen beam-induced quenches have occurred; eight of them during specially designed quench tests, the others during injection. There has not been a single beam- induced quench during normal collider operation with stored beam. The conditions, however, are expected to become much more challenging after the long LHC shutdown. The magnets will be operating at near nominal currents, and in the presence of high energy and high intensity beams with a stored energy of up to 362 MJ per beam. In this paper we summarize our efforts to understand the quench levels of LHC superconducting magnets. We describe beam-loss events and dedicated experiments with beam, as well as the simulation methods used to reproduce the observable signals. The simulated energy deposition in the coils is compared to the quench levels predicted by electro-thermal models, thus allowing to validate and improve the models which are used to set beam-dump thresholds on beam-loss monitors for Run 2.

physics.acc-ph↗

arXiv2015

Energy Deposition Studies for the Hi-Lumi LHC Inner Triplet Magnets

A detailed model of the High Luminosity LHC inner triplet region with new large-aperture Nb3Sn magnets, field maps, corrector packages, and segmented tungsten inner absorbers was built and implemented into the FLUKA and MARS15 codes. In the optimized configuration, the peak power density averaged over the magnet inner cable width is safely below the quench limit. For the integrated luminosity of 3000 fb -1, the peak dose in the innermost magnet insulator ranges from 20 to 35 MGy. Dynamic heat loads to the triplet magnet cold mass are calculated to evaluate the cryogenic capability. In general, FLUKA and MARS results are in a very good agreement.

physics.acc-ph↗