arXiv subjects

A. Herrmann

Publications and source records attributed to A. Herrmann.

8 recordsLinked to original sources

arXiv2026

Harnessing Toroidal Neutral Flows to Enhance Divertor Particle Exhaust

In 1991 Reiter et al. (1991 Plasma Phys. Control. Fusion 33 1579) considered the onerous exhaust requirements of ITER, and wrote: "The vacuum pumping problem of a fusion reactor will probably require some novel solution". Here we show that a toroidally oriented pump inlet can passively exploit intrinsic neutral flows to reduce back-flow, raise duct pressure, and ultimately improve particle-exhaust performance. Drawing on previous experimental observations and SOLPS-ITER edge-plasma simulations, we consolidate the evidence for a plasma-imprinted, multi-species toroidal neutral "wind" in detached tokamak divertors. We isolate the underlying mechanism in a prototypical divertor private-flux region using a database of two-dimensional direct simulation Monte Carlo (DSMC) calculations. The ordered neutral motion is recovered with a strong toroidal alignment, kilometre-per-second velocities, and persistence up to several centimetres across slip-to-transitional rarefied regimes (Kn=0.02$-$2). We then assess the consequences of capturing this ordered motion using a second database of idealised proof-of-principle DSMC simulations. Compared to the traditional poloidal arrangement, a toroidally oriented pump inlet reduces back-flow by up to 20% for deuterium and up to 33% for helium at 10% concentration. Partial pressures in the toroidal exhaust path are enhanced across the database, nominally by a factor of 1.78$\pm$0.04 for deuterium and 2.00$\pm$0.05 for helium. For fixed throughput, this implies a reduction in the required effective pumping speed and corresponding hardware. More broadly, these results motivate explicit retention of toroidal neutral momentum in divertor and sub-divertor modelling, and dedicated studies of neutral aerodynamics, including in stellarators, where an analogous directional imprinting is expected to occur.

physics.plasm-ph↗

arXiv2025

Multi-Machine Scaling Laws for Fuel and Impurity Puffing Rates Sufficient for Detachment Access: a Systematic Review of Magnetic Confinement Fusion Devices

An open-source database of 457 experimental and numerical entries representing 32 machines$-$including tokamaks, stellarators, and linear plasma devices$-$is assembled. From this dataset, we derive multi-machine scaling laws that predict the fuel and impurity puffing rates sufficient to edge plasma detachment$-$the leading reactor-relevant solution to the challenge of plasma-wall interaction. Validation against up to 40 L- and H-mode plasmas shows agreement within a factor of 1.5 in about 50\% of cases, and within a factor of 2 on average. Divertor volume alone is found to strongly correlate with the fuelling rate. Inclusion of plasma opaqueness leads to $\Gamma_{\text{D}} \propto [n_{\text{sep}}\, a\, (S_{\text{div}}/V_{\text{div}})^{-1.5}]^{1.05}$, valid across all toroidal devices. Its H-mode simplification, $\Gamma_{\text{D}}^{\text{HDL}} \propto 0.43\, a^{1.58}\, \lambda_q^{-0.89}$, avoids explicit dependence on $n_{\text{sep}}$ and carries intrinsic physical meaning through the H/L density limit and the power fall-off length. The impurity seeding rate is captured by a general non-linear law, from which the Greenwald-Eich-Scarabosio simplification, $\Gamma_{\text{Z}}^{\text{GES}} \propto a^{1.51}\, \lambda_q^{-0.27}$, is obtained. Similar relationships are defined for stellarators, consistent with tokamak trends but still awaiting validation$-$an opportunity for further study. These results have immediate relevance for reactor fuel-cycle design and edge plasma modelling. More broadly, they demonstrate that physics-based 0D laws can reliably link detachment access to engineering actuators, offering practical tools for reactor design. Our laws represent macroscopic patterns across machines rather than microscopic variations within an individual device$-$providing the basis for our forthcoming studies aimed at extending this framework to machine-specific behaviour.

physics.plasm-ph↗

arXiv2022

Experimental validation of the intensity refractometry principle for density measurements at the edge of a tokamak

Experimental validation is presented for a new type of microwave diagnostic, first introduced in the theoretical study in M. Usoltceva et al., Rev. Sci. Instrum. 93, 013502 (2022). A new term is adopted for this technique to highlight its difference from interferometry: intensity refractometry. The diagnostic allows measuring electron density, and in this work, it is applied at the edge of a tokamak. The implementation of this technique at ASDEX Upgrade, called Microwave Intensity refractometer in the Limiter Shadow (MILS), provides the first experimental proof of the diagnostic concept. Densities predicted by MILS are compared to several other diagnostics. The agreement and discrepancy in various radial regions of the density profile are analyzed and possible reasons are discussed. A wide density coverage is shown in the example discharges with densities from 2*10^17 m^-3 to 2*10^19 m^-3 at the limiter position. In these experiments, the radial location of the measurements varied from 5 cm in front of the limiter (up to 1 cm inside the separatrix was measured) to 3 cm in the limiter shadow. Experimental challenges of MILS operation and data processing are presented.

physics.plasm-ph↗

arXiv2022

Design and simulation of an Imaging Neutral Particle Analyzer for the ASDEX Upgrade tokamak

An Imaging Neutral Particle Analyser (INPA) diagnostic has been designed for the ASDEX Upgrade (AUG) tokamak. The AUG INPA diagnostic will measure fast neutrals escaping the plasma after CX reactions. The neutrals will be ionised by a 20 nm carbon foil and deflected towards a scintillator by the local magnetic field. The use of a neutral beam injector (NBI) as active source of neutrals will provide radially resolved measurements while the use of a scintillator as active component will allow us to cover the whole plasma along the NBI line with unprecedented phase-space resolution ($ < $ 12 keV and 8 cm) and fast temporal response (up to 1 kHz with the high resolution acquisition system and above 100 kHz with the low resolution one); making it suitable to study localised fast-ions redistributions in phase-space.

physics.plasm-ph↗

arXiv2016

ExB analyzer for fast ion temperature measurements in scrape-off layer of the ASDEX Upgrade and COMPASS tokamaks

Ion temperature in the scrape-off layer is an important quantity but rarely measured at high temporal resolution. In order to achieve fast measurements during intermittent events such as blobs, a novel ExB analyzer has been designed. The measurement with the E$\times$B analyzer does not require voltage sweeping but records ion current on DC biased collectors, meaning that the temporal resolution is only limited by the sampling frequency of the data acquisition system and electronics of the amplifiers, which exceeds the typical timescale of events of interest (~10 microseconds). The analyzer is equipped with entrance slit of optimized knife-edge shape, which reduces selective ion losses and improves overall ion transmission. The design of the analyzer is presented together with first acquired signals and reconstructed temperatures.

physics.plasm-ph↗

arXiv2000

Force-distance studies with piezoelectric tuning forks below 4.2 K

Piezoelectric quartz tuning forks have been employed as the force sensor in a dynamic mode scanning force microscope operating at temperatures down to 1.7 K at He-gas pressures of typically 5 mbar. An electrochemically etched tungsten tip glued to one of the tuning fork prongs acts as the local force sensor. Its oscillation amplitude can be tuned between a few angstroms and tens of nanometers. Quality factors of up to 120000 allow a very accurate measurement of small frequency shifts. Three calibration procedures are compared which allow the determination of the proportionality constant between frequency shift and local force gradient based on the harmonic oscillator model and on electrostatic forces. The calibrated sensor is then used for a study of the interaction between the tip and a HOPG substrate. Force gradient and dissipated power can be recorded simultane-ously. It is found that during approaching the tip to the sample considerable power starts to be dissipated although the force gradient is still negative, i.e. the tip is still in the attractive regime. This observation concurs with experiments with true atomic resolution which seem to require the same tip-sample separation.

cond-mat↗

arXiv2000

Operation characteristics of piezoelectric quartz tuning forks in high magnetic fields at liquid helium temperatures

Piezoelectric quartz tuning forks are investigated in view of their use as force sensors in dynamic mode scanning probe microscopy at temperatures down to 1.5 K and in magnetic fields up to 8 T. The mechanical properties of the forks are extracted from the frequency dependent admittance and simultaneous interferometric measurements. The performance of the forks in a cryogenic environment is investigated. Force-distance studies performed with these sensors at low temperatures are presented.

cond-mat↗

arXiv1999

A low-temperature dynamic mode scanning force microscope operating in high magnetic fields

A scanning force microscope was implemented operating at temperatures below 4.2K and in magnetic fields up to 8T. Piezoelectric quartz tuning forks were employed for non optical tip-sample distance control in the dynamic operation mode. Fast response was achieved by using a phase-locked loop for driving the mechanical oscillator. Possible applications of this setup for various scanning probe techniques are discussed.

cond-mat↗