Design and Physical Constraints of Synthetic-Frequency Photonic Switching Fabrics

Jorge Parra

Home/Archive/arXiv

arXiv · 2609.01130

Design and Physical Constraints of Synthetic-Frequency Photonic Switching Fabrics

Jorge Parra

View original source ↗Read source document ↗Export metadata ↓

Abstract

Electro-optic frequency conversion and synthetic-frequency coupling are established functions in integrated photonic devices. Their role within a multiport switching fabric, however, depends on how simultaneous optical connections share spatial paths, frequency channels, and device controls. Here, we investigate how coherent coupling among frequency modes can be incorporated into photonic switching fabrics and identify the corresponding architectural and physical constraints. We show that synthetic-frequency coupling does not increase the number of simultaneous orthogonal frequency channels when all channels are freely accessible, but can establish connections that are otherwise blocked by fixed input frequencies, channel-continuity requirements, or unavailable output channels. Under the tested conditions, coupling over the first three frequency spacings in an $8\times8$ fabric with eight frequency channels per port achieves 96.1% of the blocking reduction obtained with unrestricted inter-mode coupling. We further show that a separate frequency-only conversion stage cannot replace missing spatial connectivity. A nominal reduction in spatial switching elements instead requires a joint element whose spatial state can be programmed independently for each frequency channel. Finally, we evaluate a thin-film lithium niobate resonator model using reported electro-optic coupling and photon-decay scales within a multistage Mach-Zehnder interferometer switching fabric. These results clarify the architectural role of synthetic-frequency coupling and the device-level requirements for incorporating it into integrated photonic switching fabrics.

Explore related subjects

physics.optics cs.ET

Keep this discovery

BibTeX RIS

Jorge Parra. 2026-09-01. Design and Physical Constraints of Synthetic-Frequency Photonic Switching Fabrics. https://arxiv.org/abs/2609.01130

Cite the original work for its findings. Save a collection to share your selection of sources.

Discover connections

cs.ET subject physics.optics subject

Connections use source metadata and explicit phrase matches, not verified experimental comparisons.

KEEP EXPLORING

Related papers

arXiv2026

Sensitivity Comparison of Microwave-Frequency and Optical Fibre Interferometry Based on State-of-the-Art Components

We compare the sensitivity of fibre interferometers to vibrations using microwave oscillators and state of the art lasers over distances up to 70 km. High spectral purity lasers outperform only above 10 Hz, highlighting microwave advantages at low frequencies and the potential of hybrid microwave optical interferometry systems

physics.optics↗

arXiv2026

Towards a universal meta-optics solver via large language models

Metasurface design increasingly requires fast models that can operate across structurally distinct device families, rather than retraining a separate surrogate for every geometry class. Conventional neural network surrogates often depend on fixed-dimensional descriptors, family-specific output formats, and repeated architecture tuning, which limits their scalability across heterogeneous meta-atoms. Here, we present a unified large language model (LLM) workflow for multi-family metasurface modeling and inverse-design. Geometries, design parameters, and optical response channels were converted into a shared instruction-following text format and used to fine-tune Gemma-2-9B across 8 metasurface families. Compared with single-family baselines, the joint model simultaneously predicted the optical responses of all metasurface families while reducing the MSE for each family by an average of 56.5%. The same representation was also used for inverse design. These results show that a shared sequence-based LLM interface can provide a practical route to cross-family metasurface design while reducing the need for task-specific surrogate architectures.

physics.optics↗

arXiv2026

Making the Discrete Continuous: Synthetic RAW Augmentations for Fine-Grained Evaluation of Person Detection Performance in Low Light

Real-world deployment of AI vision models is both fueled and limited by the data available for training and testing. Real datasets are sparse and uneven: long-tailed or unbalanced distributions hinder generalization, and the low number of samples in low density regions makes it hard to run evaluations. Synthetic data can fill these gaps, providing us with a way to sample the input space more continuously and improve data coverage for benchmarks. Focusing on the autonomous driving safety-critical case of pedestrian detection in the dark, we show how synthetic low-light samples can be used to better characterize the performance of a state-of-the-art object detection model as a function of the scene illumination. We use a synthetic RAW image augmentation technique to generate low-light samples that match the noise model of the camera sensor. Performance metrics on real and synthetic low-light data are similar, indicating that the AI model finds it hard to distinguish between them.

cs.CV↗