arXiv Science⌕ Search
Home/Archive/arXiv

arXiv · 1804.01515

Crystal plasticity simulation of the effect of grain size on the fatigue behavior of polycrystalline Inconel 718

A. Cruzado·S. Lucarini·J. LLorca·J. Segurado
View original source ↗Read source document ↗Export metadata ↓

Abstract

A microstructure-based model that accounts for the effect of grain size has been developed to study the effect of grain size on the fatigue life of Inconel 718 alloys. The fatigue behavior of two alloys with different grain size was determined by means of uniaxial cyclic deformation tests under fully-reversed deformation ($R_\varepsilon$ = -1) at 400$^\circ$C in the low cycle fatigue regime. The model was based in the determination of the fatigue indicator parameter (based on the local crystallographic strain energy dissipated per cycle) by means of computational homogenization of a representative volume element of the microstructure. The mechanical response of the single crystal within the polycrystal was modelled through a phenomenological crystal plasticity model which was modified to account for the effect of grain size on the monotonic and cyclic hardening/softening mechanisms. The microstructure-based crack initiation model parameters were calibrated from the experimental tests of the material with fine grain size. The results of the fatigue simulations were in good agreement with the experimental results in terms of the cyclic stress-strain curves and of the number of cycles for fatigue crack initiation. The model did not show any grain size effect on the fatigue life for the largest cyclic strain ranges while the predicted fatigue life predicted was considerably longer in the case of the microstructure with fine grain size for the lowest strain ranges, in quantitative agreement with experimental data. These differences were attributed to changes in the deformation modes between homogeneous plastic deformation at large cyclic strain ranges and localized plasticity in a few grains at low cyclic strain ranges.

Explore related subjects

cond-mat.mtrl-sci

Keep this discovery

BibTeXRIS

A. Cruzado, S. Lucarini, J. LLorca, J. Segurado. 2018-04-04. Crystal plasticity simulation of the effect of grain size on the fatigue behavior of polycrystalline Inconel 718. https://doi.org/10.1016/j.ijfatigue.2018.04.018

Cite the original work for its findings. Save a collection to share your selection of sources.

KEEP EXPLORING

Related papers

arXiv2026

Measuring chiral phonons

Chiral phonons are quantized vibrations where the atomic motion in a solid breaks improper rotation symmetries. In many cases, chiral phonons possess angular momenta and are therefore selective to circularly polarized light. Both fundamental and applied research efforts on chiral phonons have been gaining increasing attention owing to their importance in a variety of fields including spintronics, spin-selective chemical reactions, thermal transport, quantum information processing and biosensing, where the bi-directional spin-lattice coupling enabled by chiral phonons can be harnessed in new ways, and potentially lead to new functionalities. Thus far, the studies of chiral phonons across diverse materials platforms have evolved largely independently within these fields, but the experimental techniques are often interrelated. In this perspective, we present a detailed description, as well as advantages and disadvantages of the current approaches for experimentally measuring chiral phonons in chiral and achiral materials. We conclude with a discussion of new methods for measuring chiral phonons. Ultimately, this work seeks to offer an experimental guide for systematically investigating the properties of chiral phonons in various materials systems and applications.

cond-mat.mtrl-sci↗
arXiv2026

A model of grain growth in UN integrating molecular dynamics, phase-field modeling, and uncertainty quantification

Grain growth kinetics and grain-boundary (GB) properties in uranium mononitride (UN) are investigated through an integrated multiscale framework combining molecular dynamics (MD), phase-field modeling, and surrogate-assisted uncertainty quantification. MD simulations yield GB energies for 27 symmetric tilt boundaries from 0--2000~K, which are consistent with available DFT values. The average GB energy is nearly temperature-independent below 1000~K and increases at higher temperatures. A mechanistic pore-drag model applied to the only available grain growth dataset for actinide nitrides yields a mobility reduction factor of $s \approx 0.93$--$0.99$, statistically indistinguishable from unity, confirming that pore drag is negligible under the experimental conditions. The intrinsic GB mobility is therefore extracted directly from the effective mobility, yielding $M_0 = 2.05\times10^{-15}$~m$^4$/(J$\cdot$s) and $Q_M = 0.89$~eV. Phase-field simulations conducted from 1500--2000~K confirm normal curvature-driven grain growth, with grain size distributions converging to the Hillert-like form. A surrogate-assisted global sensitivity analysis---combining principal component analysis, Gaussian process regression, and Sobol decomposition---reveals that the mobility prefactor $M_0$ dominates output variance at all times, followed by the activation energy $Q_M$, while the GB energy $\gamma$ contributes minimally. These results establish the first quantitative grain growth framework for UN and identify the reduction of uncertainty in $M_0$ and $Q_M$ as the highest-priority target for future experimental efforts.

cond-mat.mtrl-sci↗
arXiv2026

Silicon Solar Cell Design for >30% Efficiency via Singlet Fission

Singlet fission (SF) materials convert high-energy photons into multiple charge carriers, providing a route to exceed the efficiency limits of single-junction silicon solar cells without many of the complexities of multi-junction tandem designs. Following the first demonstration of an SF-enhanced silicon solar cell in 2025, there is a need to understand how SF materials can be effectively integrated into high-efficiency industrial silicon devices and translated from proof of concept to a manufacturable technology. Using coupled optical and electrical simulations, we assess the efficiency potential of several industrially relevant silicon cell architectures combined with SF materials. Interdigitated back-contact (IBC) cells offer the greatest potential for improvement due to unrestricted front-surface access and can achieve efficiencies exceeding 33%. However, performance is highly sensitive to front-surface passivation quality. Appropriate silicon design, particularly controlled surface doping and fixed interfacial charge, can mitigate recombination losses and relax passivation requirements for ultra-thin exciton-transfer layers.

cond-mat.mtrl-sci↗